Henny Penny LOV LVG-100 Series Guide

Maintenance Filter Daily FR 06 D01
FM07-577-C ©McDonald’s Corporation · Planned Maintenance Manual · Revised October 2010 Page 1 of 3
Henny Penny Corp Low Oil Volume Fryer-Gas LVG-102; LVG-103; LVG-104 Daily FR 06 D01
Why Cleans the vat of crumbs and filters the oil thoroughly to prolong the life of the oil
Time required 5 minutes to prepare 10 minutes per vat to complete
Time of day During low volume hours.
Hazard icons
Tools and supplies
Gloves, filtering Face shield Apron, heat-resistant Scouring tool McFiltering Kit for
built-in filtering
system, sample
Procedure
1 Put on protective gear
Use all McDonald’s approved
safety equipment, including
apron, face shield and gloves.
Hot oil can cause severe
burns
2 Check filter pan
Make sure filter drain pan and
pan cover are properly in
place with filter lock (right)
engaged and the filter pipe is
tightly connected (left).
If the filter drain pan or pan
cover are not properly in
place, “CHK PAN” shows in
display.
3 Press and hold FILTER button
Make sure oil is hot to get the
best results from filtering and
then press and hold the
FILTER button until 1.AUTO
FILTER shows in display
4 Press DOWN button
Press DOWN button and
display shows 2.MAINT
FILTER?
5 Press button
Press button and display
shows MAN FILTER along
with YES NO. Press button
for YES to drop oil and
display shows DRAINING.
Press Xfor NO and controls
return to normal operation.

Maintenance Filter (continued)
FM07-577-C ©McDonald’s Corporation · Planned Maintenance Manual · Revised October 2010 Page 2 of 3
Henny Penny Corp.Low Oil Volume Fryer-Gas LVG-102; LVG-103; LVG-104 Daily FR 06 D01
6 Scrub inside vat
Use the scouring tool, a nylon
scouring pad, and a small
amount of McD’s Fryer
Cleaner to scrub inside the
vat.
Be careful not to damage the
sensing probes or high limit.
7 Scrub complete
Once the vat is clean and
display shows SCRUB VAT
COMPLETE? press button
for YES. Display shows
WASH VAT? along with
YES NO.
8 Washing
Press button for YES and
display shows WASHING.
Oil is circulated through the
vat.
9 Wash again
Once wash cycle is complete,
display shows WASH
AGAIN? along with YES
NO. If vat is not yet clean,
press for YES and step 9 is
repeated.
10 Rinsing
If vat is clean, press Xfor NO
and RINSING shows in
display. The oil is pumped
into the vat and rinses it.
11 Rinse again
Once completed, the display
shows RINSE AGAIN?,
along with YES NO. If vat is
not yet clean, press for YES
and step 11 is repeated.
12 Polish
If vat is clean, press Xfor NO
and POLISH show in display,
along with YES. Press 
button for YES and the oil is
circulated through the filter
system for 5 minutes.
A polish cycle can be stopped
anytime by pressing the 
button under the words STOP
POLISH.
13 Fill vat
Once the polish cycle is
complete, FILL VAT shows
in display, along with YES.
Press button for YES and
display shows FILLING and
the vat fills with oil.
14 Back to normal operation
Once vat is full, display
shows IS POT FILLED?
along with YES NO. Press 
button for YES and fryer
returns to normal operation.
15 Power switch on
Make sure the main power
switch is in the ON position.
If the filter pad has not been
changed, a reminder
“CHANGE PAD” shows on
the display. Press #1 button
to cancel the message, but it
reappears every 4 minutes
until the filter pad has been
changed.

Maintenance Filter (continued)
FM07-577-C ©McDonald’s Corporation · Planned Maintenance Manual · Revised October 2010 Page 3 of 3
Henny Penny Corp.Low Oil Volume Fryer-Gas LVG-102; LVG-103; LVG-104 Daily FR 06 D01
16 Pull-out filter drain pan
Open the door, lift-up on the
drain pan stop and pull-out
the filter drain pan assembly,
using the handle on the drain
pan
This pan could be hot! Use
protective cloth or glove, or
severe burns could result.
17 Remove filter drain pan cover
Lift the pan cover from the
drain pan.
18 Remove crumb basket
Lift the crumb basket from
the drain pan. Wipe the oil
and crumbs from the crumb
basket. Clean the crumb
basket with soap and water,
then thoroughly rinse with hot
water.
19 Remove filter pad retaining
ring
Remove the filter pad
retaining ring and clean
thoroughly with soap and
water. Rinse thoroughly with
hot water.
20 Remove filter pad from pan
Pull the filter pad from the
pan and discard pad
21 Remove bottom screen
Pull the bottom screen from
pan and clean thoroughly with
soap and water. Rinse
thoroughly with hot water.
22 Clean filter drain pan
Wipe the oil and crumbs from
the drain pan.
23 Reassemble
Reassemble in reverse order,
placing the bottom screen into
the filter pan first, followed
by the filter pad, retaining
ring and the crumb catcher.
Be sure that the drain pan,
bottom screen, crumb catcher,
and the retaining ring are
thoroughly dry before placing
filter pad into pan as water
will dissolve the filter pad.