Hi Sharp HS-DVR045 User manual

1
Thank you for purchasing our product.
Please read this User’s Manual before
using the product. Change without Notice
4 Channel Digital Video Recorder
User’s Manual

2
CAUTION
RISK OF ELECTRICAL
SHOCK. DO NOT OPEN !
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER (OR BACK), NO USER
SERVICEABLE PARTS REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space limitations.
Safety Precautions
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of insulated
dangerous Voltage within the product’s enclosure that may be
sufficient magnitude to constitute risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operation and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR
A
ttention: installation should be performed by qualified service
Personnel only in accordance with the National Electrical Code or
applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have
power supplied to the unit whenever the power cord is inserted into
the power source; however, the unit is operational only when the
ON-OFF switch is the ON position. The power cord is the main power
disconnect for all unites.
“CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer‘s instruction.”
During the warranty period (one year for Hard Disk), we will repair or
replace the hard disk free of charge.
Be sure to have the model number, serial number and vendor stick on
hard disk for service representative.
Warranty
and Service

3
Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in this Users
Manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow manual
instruction for appropriate installation.
1. This document is intended for both the administrator and users of stand alone DVR Model.
2. This manual contains information for configuring, managing and using stand alone DVR Model.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture
4. Be sure to read this manual before using stand alone DVR Model.
5. For questions and technical assistance of this product, contact your local dealer.
►Strong recommendation on installation of the DVR unit
1. Check electricity at the place you want to install the DVR unit is stable and meets our electricity
requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
2. Several chips on the main board of the DVR unit and hard disk drive inside the unit generate heat, and it
must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the left side of the unit and do not close up an
opening (fresh air in-take) on the right side of the unit..
3. Put the DVR unit at well-ventilated place and do not put heat-generating objects on the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built-in
ventilation fan of the rack is properly running.
About this document
Before reading this document

4
Safety Precautions………………………………………………….……………………………………….. 2
Content Table……….………………………………………………………………………………………… 4
1. Hardware……………………………………………………………………………………………………… 4
2. Unit Description of Front Panel…………………………………………………………………………….. 5
3. Unit Description of Rear Panel……………………………………………………………………………… 6
4. Installation……………………..……………………………………………………………………………… 7
1. Procedure………………………..……………………………………………………………….… 7
2. Picture……………………………………………….……………………………………………… 9
3. Playback………..………..……………………………………………….………………………… 11
5. Function Setup…………………..………………………………………………………….………………… 13
1. Log-in………..…………………………….……….……………………………………………….. 13
2. Basic Operation…………………………………………….……………………………………… 14
6. Specifications……………………..……..………………………………………………………………….… 36
7. PTZ Control……………………………………………..………………………………………………..…… 38
1 X DVR Machine
1 X Power Core (Power core type depends on your order)
1 X Adaptor 12V / 5A
1 X User Manual
1 X Remote controller
1X CD
8 X Screw (Without Hard Disk)
4 X Screw (Within one Hard Disk)
Content Table
Hardware

5
1 ~ 4 camera channel full screen choose button / 0 ~ 9 password input
Unit Description of Front Panel
Picture 2x2 zoom in
Picture Freeze
4 quad split screen display button
Channel auto sequence button
Picture in picture button
Function menu button
Time search button
Key lock button
Function exit button
Value change button
Direction button Up and Down /
Record or playback stop /
playback pause or step button.
Direction button left and right,
Fast / Slow Reverse,
Fast / Slow forward playback.
Shuttle
Remote controller IR
USB port
PIP
ZOOM
FREEZE
POP Picture on picture button
AUTO
MENU
ESC
LOCK
BACKUP Image backup button
T-SRH
PLAY Image playback button
REC Image record button

6
Unit Description of Rear Panel
Power code in 12V/5A, power switcher
Camera 1 ~ 4 in and out
Audio channel input x 4 and
output x 2
Monitor out
Network connector. (Not available currently)
VGA
VGA output. PC monitor connector.
(OPTIONAL)
RS 485 A + / B –
Alarm In: 1 / 2 / 3 / 4
Relay: NO / NC / COM

7
1) Camera Connection
Connect the camera to the CAMERA INPUT
on the Rear Panel of the 4 CH DVR.
2) Monitor Connection (Composite Connection
Method)
Connect the monitor to the MONITOR OUT on
the Rear Panel of the 4 CH DVR.
3) Sensor Connection
Connect the Sensor to the SENSOR INPUT/
OUTPUT on the Rear Panel of the system
◆Relay output : COM+NC, COM+NO
◆Alarm input : Short-circuit between Alarm1, Alarm2, Alarm3 or Alarm4 and GND is recognized
as alarm. Alarm 1~4 = Camera1~4.
NOTICE: Sensor input is RECOGNIZED as LOW when alarm signal is on a level with GND, and it is
recognized as HIGH when alarm signal is FLOATING or 5V. Following is internal circuit.
Thus, there is a danger of damage, when the sensor input goes to a Negative level or voltage higher
than 5V.
Installation
Procedure
CH1 CH2 CH3 CH4
CH1 CH2 CH3 CH4
MONIT OR
VIDEO
LENS
VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear part of CAMERA
Internal Circuit D1
5
V
CH1 CH2 CH3 CH4
CH1 CH2 CH3 CH4
MONITOR
VIDEO
LENS
VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear part of CAMERA

8
4) HDD internal connection
Notice:
-The 4 CH DVR provides 2 removable rack hard drives.
-Hard Disk Master and Slave jumper pin must right, otherwise it makes DVR work fault.
5) Power Connection
Connect the power to the POWER
CONNECTION on the Rear Panel of the
system, and turn on the switch.
6) Turn on the POWER.
Make sure the adaptor is 12V/5A.
7) Detail setup in SYSTEM SETUP
For detail setup, refer to the instruction of SYSTEM SETUP.
1. Make sure the HDD is MASTER.
2. Make sure the cable connector is
correct.
3. MASTER set up, please check the
HDD panel.
1. Make sure the HDD is MASTER and
SLAVE.
2. Make sure the cable connector is
correct.
3. MASTER and SLAVE set up, please
check the HDD panel.
HDD
MASTER
MAIN BOARD
I/O BOARD
Set the drive jumpers as specified by hard disk drive manufacturer.
1
2
3
1
3
2
tie
HDD1
HDD2
MASTER
SLAVE
MAIN BOARD
I/O BOARD
Set the drive jumpers as specified by hard disk drive manufacturer.
21
3
1How to connect single HDD 2How to connect 2 HDD

9
Full screen or quarterly split screen display
Press quad button to display 4 quarterly split screen.
Press numeric 1 / 2 / 3 / 4 buttons to display the desired camera image in full screen.
1.) FREEZE Mode
1. In live and the quad mode press (FREEZE) button to freeze image.
Press again to cancel freeze mode.
2. On the full screen display, press (FREEZE) button to
freeze full screen image.
2.) Zoom Mode(Display Enlargement.)
Go to full screen mode with numeric buttons of live mode, then press ZOOM button to display screen
Enlargement.
Use button to move position.
3.) Auto Mode
Press (AUTO) button begins to screen auto sequence.
4.) PIP (PICTURE IN PICTURE)
1.) Press (PIP) button. Press (AUTO) button begins to sub-screen auto sequence.
2) With button, select the main channel screen, press button to select desired camera
channel in small screen.
Main picture
Sub picture
Picture

10
4.1) POP (PICTURE ON PICTURE)
1.) Press POP button to display pictures on screen. Press (AUTO) button begins to sub-screen auto
sequence.
5.) Alarm Sensor Recording
See the alarm recording setup page
6.) Scheduled Recording
See the scheduled recording setup page
7.) Motion detection Recording
See the motion detection recording setup page
8.) Key Lock function
On the Live mode, press (lock),
Only, numeric, freeze, auto, pip, and zoom buttons could work. Press lock key again to enter the login-in
window. Enter admin or user password to unlock.
9.) Audio function
4 audio channel record, 1 audio output at once time.
See the advanced setupÆRecord setup
10.) BACKUP
Notice
1> Recording is not possible if no camera is connected.
2> PES. All channels are record in quad. Use Video Viewer to play back. Screen can display on full
channel or quad. AVI, each camera play back.
CAMERA1
CAMERA 2
CAMERA 3
CAMERA 4
BACKUP SETUP PAGE
1. BACKUP DEVICE USB
2. DETECT
3. FORMAT USB
4. BACKUP FORMAT PES
5. BACKUP CHANNEL 1 2 3 4
START: xxxx/xx/xx xx:xx:xx
END:
BACKUP SIZE: x / MB
START BACKUP
1.Device USB.
2.Detect: Detect device.
3.USB data format.
4. Image format: AVI or PES.
PES. Need the AP software from factory.
5. Choose channel. v means this camera is chosen.
Size: Current / Total

11
1. Playback Mode
1) Press button to begin playback.
(System will playback the previous time recording.)
2. T-SRH button
T-SRH: Playback by time search.
Press T-SRH button to active playback function.
1) EVENT LIST (Alarm List): Event source- Video loss / Alarm trigger / Motion / Pwreset (DVR
reboot)
12 items display each page. Total 1024 items.
Playback
PLAY
PLAY SETUP PAGE
EVENT LIST
TIME LIST
FIRST: xxxx/xx/xx xx:xx:xx
LAST: xxxx/xx/xx xx:xx:xx
GOTO: xxxx/xx/xx xx:xx:xx
PLAY GOTO TIME
OCCURRED TIME CH TYPE
Press direction button
UP/DOWN to choose
items.

12
2) TIME LIST (Playback image by Time-Search): Recorded images list (by hours)
FIRST: xxxx/xx/xx xx:xx:xx (The FIRST date and time recording display).
LAST: xxxx/xx/xx xx:xx:xx (The final date and time recording display).
GOTO: xxxx/xx/xx xx:xx:xx (year / month / day, Hour / Minute / Second)
Press values change button to change date and time values.
PLAY GOTO TIME
After date and time input, direction move to PLAY GOTO TIME, press ENTER to start playback.
TIME SEARCH LIST PAGE
Press direction button Left/Right to change date and time values position.

13
1) Press MENU button to enter into menu. You could do the system function setup in MENU.
2) Password enter window pop-up:
3) Press numeric (0 ~ 9)button to choose password.
4) Remote controller function buttons are same as DVR panel function buttons.
Notice:
1. ADMIN level can setup all DVR menu functions.
2. USER level cannot setup ADVANCED page of DVR main menu function.
3. GUEST level cannot setup anything.
LOGIN
Default password (Account-Admin): 00000
Default password (Account-User): 11111
Default password (Account-GUEST): 22222
FUNCTION SETUP
LOGIN DVR SYSTEM
PASSWORD xxxxx

14
Press MENU button to enter MAIN SETUP PAGE.
1) Use direction button up/down button to select setup item.
2) Press button to enter into sub-menu function setup.
3) Press sub-menu item with direction button up/down
or left/right button.
And change the value with values change button or turn inner-shuttle.
4) Press ESC to go back to main / sub menu or exit menu.
Basic Operation
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4.CAMERA SETUP
5. BUZZER&RELAY SETUP
6. SYSTEM SETUP
7.PTZ SETUP
8.ADVANCED SETUP

15
1. HDD INFORMATION
Use direction button up/down button to select HDD INFORMATION item position.
Press ESC to go back to main menu or exit menu.
>NO: Hard disk amount
>Size: Hard disk capacity display. xx GB.
>USED: Hard disk %. If sets overwrite, after hard disk full then starts to overwrite, it displays OW.
Harddiskfullis99%.
>Brand: DVR system auto detect hard disk brand after power on.
-Status: IDLE / RECORDING
START: xxxx(Y)/xx(M)/xx(D) xx:xx:xx(H:M:S)
The first recording date and time display.
END: xxxx(Y)/xx(M)/xx(D) xx:xx:xx(H:M:S)
The last recording date and time display.
NO. SIZE USED BRAND
01 080GB OW SEGATE
STATUS: USE
START: xxxx(Y)/xx(M)/xx(D) xx:xx:xx(H:M:S)
END: xxxx(Y)/xx(M)/xx(D) xx:xx:xx(H:M:S)
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3. DISPLAY SETUP
4.CAMERA SETUP
5. BUZZER&RELAY SETUP
6. SYSTEM SETUP
7.PTZ SETUP
8.ADVANCED SETUP

16
2. DATE-TIME SETUP
1. Hour Type: 12H/24H:MM:SS. 12 Hour Format / 24 Hour Format.
2. Date Type: YY/MM/DD, MM/DD/YY, DD/MM/YY, YY/ENG/DD, ENG/DD/YY, DD/ENG/YY,
YYYY/MM/DD, MM/DD/YYYY, DD/MM/YYYY, YYYY/ENG/DD, ENG/DD/YYYY, DD/ENG/YYYY.
Y=Year. M=Month. D=Day. ENG=Month display in English.
01=January; 02=February; 03=March; 04=April; 05=May; 06=June;
07=July; 08= August; 09=September; 10=October; 11=November; 12=December.
3. Date: 2003/01/01
4. Time: 12/30/49 > Use direction button up/down choose position, values change button to change
date and time values.
-Please stop REC function first if you want to change the time.
5. Date and Time position setup:
>User can see the date-time position moving when pressing direction buttons.
Press direction button up/down/left/right to choose items or move date-time position.
**** DATE-TIME POSITION****
UP
DOWN
LEFT RIGHT
ENTER for Default
ESC to QUIT
DATE-TIME SETUP PAGE
1. HOUR TYPE:
2. DATE TYPE
3. DATE 2000 / 00 / 00
4. TIME
5. DATE-TIME POSITION SETUP
MENU, ESC:EXIT, :MODIFY
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3.DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER&RELAY SETUP
6. SYSTEM SETUP
7.PTZ SETUP
8. ADVANCED SETUP

17
3. DISPLAY SETUP
1. DATE-TIME: Date and Time caption display mode on or off setup.
>ON / OFF
2. CAMERA TITLE: Camera Title caption display mode on or off setup.
>ON / OFF
3. PB DATE-TIME: Play back date and time caption display mode on or off setup.
>ON / OFF
4. PB CAMERA TITLE: Play back camera title caption display mode on or off setup.
>ON / OFF
5. DVR STATUS: DVR system, record, playback, audio caption display mode on or off setup.
>ON / OFF
6. BORDER SET: Border color WHITE / BLACK / DARK / GRAY / OFF
7. VLOSS DISPLAY
>ON / OFF
Press direction button up/down to choose the desired item.
Press values change button to change values.
DISPLAY SETUP PAGE
1.DATE-TIME ON
2. CAMERA TITLE ON
3. PB DATE-TIME ON
4. PB CAMERA TITLE ON
5.DVRSTATUS ON
6. BORDER SET WHITE
7. VLOSS DISPLAY ON
MENU, ESC:EXIT, :MODIFY
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3.DISPLAY SETUP
4.CAMERA SETUP
5. BUZZER&RELAY SETUP
6. SYSTEM SETUP
7.PTZ SETUP
8.ADVANCED SETUP

18
4. CAMERA SETUP
(1.) COLOR SETUP
CAMERA-COLOR SETUP : Adjust Camera Image
CH NUMBER : Select camera
BRIGHTNESS : Adjust screen brightness (-31~ +32)
CONTRAST : Adjust color contrast (-31~ +32)
SATURATION : Adjust color saturation (-31~ +32)
HUE :Adjustcolorhue (-31~+32)
>DEFAULT RESET<: Press ENTER button to reset DVR values.
>Right adjustment of each element in COLOR setup will increase picture quarterly displayed.
We recommend you to adjust each element of COLOR SETUP for cameras and monitor to
be connected to the DVR unit.
Press direction button up/down to choose items.
Press values change button to change values.
CAMERA SETUP PAGE
1. COLOR SETUP
2. TITLE SETUP
3. MARK&MIRROR SETUP
MENU, ESC: EXIT, ENTER: RUN
CAMERA SETUP
1. COLOR SETUP
2. TITLE SETUP
3. MARK&MIRROR SETUP
CAMERA COLOR SETUP PAGE
** CH NUMBER 01
1. BRIGHTNESS +0
2. CONTRAST +0
3. SATURATION -2
4.HUE +1
>DEFAULT RESET<
MENU,ESC:EXIT, :MODIFY
MAIN SETUP PAGE
1. HDD INFORMATION
2. DATE-TIME SETUP
3.DISPLAY SETUP
4. CAMERA SETUP
5. BUZZER&RELAY SETUP
6. SYSTEM SETUP
7.PTZ SETUP
8.ADVANCED SETUP

19
(2.) TITLE SETUP: Input TITLE of each camera. 14 characters can be input.
Characters choose:
Numeric: 0 / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
Capital letter: A / B / C / D / E / F / G / H / I / J / K / L / M / N / O / P / Q / R / S / T / U / V / W / X / Y / Z
SPACE
Press direction button up/down/left/right to choose items and position.
Press values change button to change values.
CAMERA SETUP
1. COLOR SETUP
2. TITLE SETUP
3. MARK&MIRROR SETUP
CAMERA TITLE SETUP PAGE
CH1(CAM01 )
CH2(CAM02 )
CH3(CAM03 )
CH4(CAM04 )
MENU, ESC: EXIT: : MODIFY

20
3.)MASK&MIRROR SETUP
MASK&MIRROR SETUP PAGE
**MASK FUNCTION OFF / ON
1. CH 1: OFF / ON
2. CH 2: OFF / ON
3. CH 3:OFF / ON
4. CH 4:OFF / ON
**MIRROR FUNCTION OFF / ON
1. CH 1: OFF / ON
2. CH 2: OFF / ON
3. CH 3: OFF / ON
4. CH 4: OFF / ON
CAMERA SETUP
1. COLOR SETUP
2. TITLE SETUP
3. MARK&MIRROR SETUP
MASK&MIRROR SETUP PAGE
**MASK FUNCTION OFF
1. CH 1: OFF
2. CH 2: OFF
3. CH 3: OFF
4. CH 4: OFF
**MIRROR FUNCTION OFF
1. CH 1: OFF
2. CH 2: OFF
3. CH 3: OFF
4. CH 4: OFF
Press direction button up/down/left/right to choose items and position.
Press values change button to change values.