HiBoost Mini F08GI-5S-BTW User manual

1/ 14
User'sManual
F08GI-5S-BTW
MADE IN HUAPTEC

2/ 14
Content
WHAT IS INCLUDED ..................................................................................3
1HOW IT WORKS.................................................................................3
2TOOL REQUIRED................................................................................3
3HOW TO INSTALL YOUR NEW CELLULAR BOOSTER............................4
3.1 Overview...................................................................................4
3.2 Plan the layout of your system ..................................................6
3.3 Check for Signal Strength ..........................................................6
3.4 Run coaxial cable.......................................................................6
3.5 Install the Donor (Outdoor) antenna .........................................6
3.6 Install the Server (Indoor) antenna............................................7
3.7 Install your cellular booster .......................................................7
3.8 Power up your cellular booster .................................................7
4UNDERSTAND THE PORTS and LED STATUS,MGC...............................8
4.1 Repeater ports ........................................................................ 8
4.2 LED Status .................................................................................8
5UNDERSTAND THE ANTENNA ............................................................9
5.1 Donor (Outdoor) antenna .........................................................9
5.2 Server (Indoor) antenna ............................................................9
5.3 Authorized Kitting Options ........................................................9
6TROUBLESHOOTING ........................................................................10
7FREQUENTLY ASKED QUESTIONS.....................................................12
8FCC RF Exposure Statement ............................................................12
9Warning and Statement ..................................................................12

3/ 14
WHAT IS INCLUDED
1. HiBoost Mini
2. Outdoor Antenna & Cable
3. Indoor Antenna &Cable (option)
4. AC/DC Power Adapter
1HOW IT WORKS
The cellular booster provides reliable two-way cellular coverage by improving signal
strength in homes, buildings, offices, and other areas where cellular reception is weak
or unreliable.
The system amplifies the signal from the nearest cellular tower and retransmits at a
higher power level within a local area.
This manual provides simple installation instructions that will have your cellular
booster kit running in record time.
2TOOL REQUIRED
Phillips Screwdriver
Drill
Cellular Phone (to check signal
strength)

4/ 14
3HOW TO INSTALL YOUR NEW CELLULAR BOOSTER
Use the built –in antenna
3.1 Overview
This guide will help you properly install your cellular booster kit. Itis important toread
through all of the installation steps before installing your equipment. Thoroughly read
through the instructions, visualize where all the equipment will need to be
installed and do a soft installation before mounting any equipment.
The installation process shown as below :
Usethe indoor antenna
1.booster 2.outdoor antenna
3.cabel 4. power supply
5.indoor antenna 6. cabel (the same as No.3 cabel )

5/ 14
1
•BOOSTER –select location
•Install the booster in an area that is protected from the weather,
properly ventilated and is away from excessive heat and moisture.
2
•DONOR ANTENNA (OUTDOOR)-select location
•Mount the signal (outdoor) antenna in an elevated outdoor location so
that it points towards the cellular tower and away from where the inside
antenna will be located.
3
•OUTDOOR COAXIAL CABLE -select location
•The outdoor coaxial cable is used to connect the donor (outdoor)
antenna to the booster.
4
•INDOOR COAXIAL CABLE-(if used)
•The indoor coaxial cable is used to connect the server (indoor) antenna
to the booster.you can choose the indoor omni antenna or panel antenna .
5
•SERVER ANTENNA (indoor)
•The ideal location for the distribution antenna will be the area of your
property where you need to improve the signal most.
•NOTE:The signal strength will be strongest closest to the antenna.
6
•IMPORTANT: The signal antenna (outdoor)should always be separated from the
distribution antenna (indoor)by at least 20 vertical feet including the separation
of a thick barrier such as a roof or a wall. Depending on the strength of your
outdoor signal, the weaker the signal the less separation distance is required.
7
•LIGHTNING SURGE PROTECTOR-(SOLD SEPARATELY)
•The lightning surge protector connects in between the signal antenna and the
booster.
•IMPORTANT: Lightning surge protector must be grounded.
8•COMMISSIONING THE SYSTEM
！

6/ 14
3.2Plan the layout of your system
Before you get started you will need to plan the layout of your system. This involves
checking signal strength for signals coming from the cellular tower, as well as antenna,
booster and cable placement.
3.3 Check for Signal Strength
Select a location on the roof of the building to install the signal antenna, by monitoring
your cellular phone’s signal strength (signal bars) to find the strongest signal from your
carrier’s cellular tower.
Mark that area as the installation location for the Donor (outdoor)
IMPORTANT: Confirm that you have at least 20 feet of vertical distance between the
marked antenna location and the location where you will place the Server (indoor)
antenna. To prevent the system from oscillation (feedback) you want to ensure that
there is enough separation between the distribution and signal antenna or that they
are shielded from each other to ensure the distribution antenna does not send a signal
back into the signal antenna. If you cannot achieve these separations, either choose
an alternate location for the donor (outdoor) antenna or determine if there are natural
barriers in the building construction itself that will attenuate signals between the two
antennas so that oscillation can be prevented.
3.4 Run coaxial cable
Loosely run the coaxial cable from your outdoor antenna to your booster. (After you
have tested the system you can permanently secure the coaxial cable).
As you route and pull cabling, follow these general guidelines:
Bend cables and route them smoothly, and protect the outer skin against any
damage.
Keep horizontal cables straight and fasten them with a tie every three to five feet.
Bind and fasten vertical cables every six to eight feet.
Waterproof all outdoor connections with silicone caulking
Be careful when plugging the connector in so as not to damage the center pins on
the connectors.
3.5 Install the Donor (Outdoor) antenna
Connect the supplied coaxial cable to the antenna. We recommend applying silicone
caulking to fully waterproof the connection.
Attach the cable in such a way that a drip loop is formed.
Once mounted, connect one end of the coaxial cable to the donor (outdoor) antenna
and the other end to the cellular booster where it is marked “Outdoor”

7/ 14
3.6 Install the Server (Indoor) antenna
If you usethe built-in antenna ,please ignore this step .
Connect one end of thecoaxial cable to the antenna and the other end to the cellular
booster where it is marked “Indoor”.
Select the installation location ofyour supplied server (indoor) antenna based on the
following:
Omni directional antenna
Place inthe center of the area where the signal needs tobe amplified.
Panel directional antenna
Place in the outer perimeter of the area the signal needs tobeamplified.
3.7 Install your cellular booster
Install the cellular booster in a location that is properly ventilated and not exposed to
excessive heat, moisture and/or direct sunlight. The optimal area would be on a wall
located near a power outlet.
It should be mounted in an easily accessible area so it’s easy to perform general
maintenance with the coaxial cable connections, dip switch settings and power
adaptor.
Make sure all cables and antennas are securely connected before commissioning the
system.
3.8 Power up your cellular booster
Once all the Following precautions have been taken, power on thecellular booster.
1. Verify that you have left at least 1 meter of vertical separation space between the
indoor and outdoor antennas.
2. Never point the front of the yagi donor (outdoor) antenna towards the inside of
the server (outdoor)antenna.
3. Verify that the supplied coaxial cables from both the donor (outdoor) antenna and
the server (outdoor)antenna are properly connected to the cellular booster before
powering it up.
4. Carefully plug in the supplied power adaptor into the back of the cellular booster
where it is marked ‘DC 12V’ and connect the other end to a power outlet.
The LED indicator marked power should light up green.

8/ 14
4UNDERSTAND THE PORTS and LED STATUS,MGC
4.1 Repeater ports
Connector
Description
Indoor
N-female connector,for connection to indoor antenna
Outdoor
N-female connector,for connection to outdoor antenna
DC 12V
Power wire port
USB
For debug connector
4.2 LED Status
LED
Status
Definition
Alarm
green
It is working properly
red
Alarm
off
No power input
Bluetooth
green
Normal
WIFI
green
Normal

9/ 14
5UNDERSTAND THE ANTENNA
5.1 Donor (Outdoor) antenna
5.2 External Server (Indoor) antenna
5.3 Authorized Kitting Options
The following accessories are authorized by the FCC to be used with the Hiboost Mini Signal
Booster. Outdoor antenna & cable kit options
Outdoor
Antenna
Outdoor Antenna Gain
Lower
700MHz Cellular PCS AWS-1
Yagi antenna 5 55 6 6
panel antenna 5 56 7 7
The Yagi Antenna
The yagi is a very precise directional antenna with a powerful reach. This
antenna should be installed in an elevated position and must be pointed
towards your carrier’s cellular tower.
NOTE:This antenna is not meant to capture signal from multiple carriers.
The Panel Antenna
The panel is a directional antenna with a 120 degree reach and is designed
to capture the signal from multiple carrier towers. This antenna should be
installed in an elevated position and must be pointed towards your carrier’s
cellular towers.
The Omni Antenna
The omni antenna is an omni-directional antenna with a 360 degree
reach. It is designed to distribute the signal from the center of the
affected area. Typically it is installed in a false or dropped ceiling.
The Panel Antenna
The panel is a directional antenna with a 120 degree reach and is
designed to distribute the signal from a perimeter wall or ceiling.
Upper
700MHz

10 / 14
Outdoor Cable
Outdoor Cable Outdoor Cable Loss
HiBoost200(50
feet) 1.2 1.2 1.2 1.25 1.25
Indoor Antenna
Indoor Antenna Indoor Antenna Gain
panel antenna 66688
Omni antenna 3 3 3 3 3
Internal antenna 00000
Indoor Cable
Indoor Cable Indoor Cable Loss
HiBoost200 (50
feet)
5.2 5.3 5.3 8.0 7.6
6TROUBLESHOOTING
Eliminate ISO warning problems:
1.Adjust the outdoor antenna direction, keeping it away from indoor antenna. Restart
booster.
2.Increase the vertical or horizontal distance between the outdoor antenna and indoor
antenna. Restart booster.
3.Use barriers such as walls to increase the isolation.
4.Change the indoor antenna type to an antenna with a more directional antenna pattern.
Orient the indoor antenna and outdoor antenna so they point in opposite directions.
5.Reduce the booster’s downlink gain via setting the gain parameter in app. Keep the uplink
gain value and downlink gain value the same then restart the booster.
Note: Uplink gain must be equal to or not less than 5dB below the downlink gain,to avoid
interference with the local carrier's cell site network.
Target: The ISO issues are solved when there is no ISO warning from the app.
Eliminate ALC warning problems:
1.Adjust the antennas’ directions or locations to lower downlink received signal level.
2.Slowly reduce the downlink gain via setting the gain parameter in app.
3.If the above methods don’t work, reduce the booster’s gain with an external attenuator in
line with the outdoor antenna or replace with lower gain antenna.
Target: The overload issues are fixed when there is no ALC warning from the app. Please
note that a low gain may result in smaller coverage area. This can be improved by adjusting
the outdoor antenna to receive a stronger signal.Eliminate poor coverage problems when
Power or ALC is warning:
1.If the signal has not been improved, please check below:
Lower
700MHz Cellular PCS AWS-1
Upper
700MHz
Lower
700MHz Cellular PCS AWS-1
Upper
700MHz
Lower
700MHz Cellular PCS AWS-1
Upper
700MHz

11 / 14
¢The weak downlink signal leads to the low output signal level. Change thedirection or
position of the outdoor antenna. You may also try replacing the outdoor antenna with a
higher gain antenna to increase the incoming signal.
*Check to see if it is necessary to add more indoor antennas. Barriers such as walls can block
the signal indoors. You should also check the booster to make sure the power is maximized.
Try installing more indoor antennas or replace the booster with a higher powered one.
2.If the signal in a small section of the building hasn't been improved, try the following:
*Check to see if the indoor antenna is installed correctly. Try moving the antenna to improve
coverage.
¢Try adjusting the direction the indoor antenna is pointing.
Check whether it is necessary to add one or more antennas to enhance the coverage of special
areas.
IMPORTANT NOTES
The 2 most important things to look for when setting up your system is:
By capturing the best input signal you will be able to enjoy the maximum coverage and
best quality signal inside where your Indoor antennas are located. The better the input
signal, the better the output signal. In order to find the best input signal, you want to
place your outdoor antenna as high as possible with the least amount of obstruction
between the antenna and the cellular base tower. A clear line of site is ideal.
Isolating the signal from the antennas is done by ensuring that the antennas are not
pointing to each other and by having enough distance or barrier shielding in between
them. The signals travel like rays of sunlight, a directional antenna will send the signal
in the direction that it is pointing. An omni directional antenna will send the signal in
every direction around it. So depending on your equipment it’s important to be sure
that your Indoor antenna is not sending the signal back into the outdoor antenna.
THINGS TO CHECK WHEN EXPERIENCING WEAK CELLULAR SIGNAL
1. Ensure the outdoor antenna is pointing in the correct direction and is capturing
adequate signal for the booster.
2. Check all connections on the cable, antennas, and booster.
3. Check cable for bends and or cuts.
4. All LED lights on the booster should be green or there are not “ALC” and “ISO”
indication on LCD.
5. Outdoor antenna and the indoor antennas have adequate separation and are not
causing feedback.
A good input signal (the best you can find)
Isolating the outdoor (donor) antenna from the indoor
(server) antennas so they do not feedback into each other.

12 / 14
7FREQUENTLY ASKED QUESTIONS
WHY ARE THE LED LIGHTS TURNING FLASHING GREEN, FLASHING
RED OR SHUTTING OFF?
There are certain cases where your system could be experiencing
oscillation. This can be attributed to either the quality of your input signal
or having your outdoor antenna and indoor antenna too close together. Please review
the following guidelines to help resolve this issue:
1. Adjust the direction of the outdoor antenna. If the system is receiving a very high
input signal, you can point your outdoor antenna away from the cellular tower to
reduce the strength of the input signal and therefore, reduce the oscillation.
Alternatively if your system is receiving a very poor quality signal (weak and
unusable signal), you can point your outdoor antenna more directly towards the
cellular tower to increase the strength of the input signal. Sometimes this may
require completely repositioning the antenna to a location where you can achieve
a line of site to the tower.
2. Increase the separation between the outdoor antenna and the indoor antenna.
This can be achieved by increasing the distance between the two antennas or by
placing barriers between them, such as moving the indoor antenna to an adjacent
room where there would be an additional wall separating them from the outdoor
antenna.
3. Manual Gain Control. Adjust the gain with the manual gain control function using
the dip switches on the side of the booster.
8FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating instruction for
satisfying RF exposure compliance. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
9Warning and Statement

13 / 14
Note:This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Huaptec could void the user's
authority to operate the equipment.
Note: For a complete list of antennas and cables approved for use with these boosters
see 5.3 Authorized Kitting Options pages 13&14&15&16.
FCC 27.50(d)(4)Statement:Fixed, mobile, and portable (hand-held) stations operating
in the 1710-1755 MHz band are limited to 1 watt EIRP. Fixed stations operating in the
1710-1755 MHz band are limited to a maximum antenna height of 10 meters above
ground.
FURTHER INFORMATION ON SIGNAL BOOSTER END-USE REGISTRATION
The following is currently active contact of US wireless provider for booster register.
https://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
https://www.sprint.com/legal/fcc_boosters.html
https://www.verizonwireless.com/solutions-and-services/accessories/register-signal-
booster/
https://support.t-mobile.com/docs/DOC-9827
https://securec45.securewebsession.com/attsignalbooster.com/

14 / 14
SHENZHEN HUAPTEC CO., LTD
5th FL, E BLDG, Sogood Science Park, Hangkong Road, Xixiang, Bao'an,
Shenzhen, China 518102
Phone/Fax: [phone]
Website: www.huaptec.com
Huaptec US Inc.
6210 N Belt Line Rd., Ste. 110, Irving, TX 75063
Phone/Fax: [phone]
E-mail: [e-mail]
Website: www.huaptecus.com
IC RF EXPOSURE STATEMENT
The device is compliance with RF exposure limits. The minimum distance from
body to use the device is 20 CM.
Le present appareil est conforme c山x conformite ou aux Ii mites d'intensite de
champ RF. La distance minima le du corps a utiliser le dispositif est de 20 CM.