HiBoost Mini Series User manual

MiniSeries
InstallationGuide
Sidekick

Package Contents
Signal Booster 1X32.8ft SMAM-NM Outdoor Cable
1X16.4ft SMAF-SMAM Outdoor Cable
Outside Antenna Indoor Whip Antenna
Through-Window-Cable
Power Supply waterproof tape
Wi light
Bluetooth lightPower light
Accessories for main parts
Sidekick
01
are all provided to protect connections SMA-Male to SMA-Female
Notes for LCD Display
Outdoor Gain:60dB Indoor
2100
MHZ
The number of bars
indicates the performance
of the device. If it shows
zero bar, you can change
the installation position
and direction of the
outdoor antenna to gain
better signal.
It shows the
boosted signal
strength. The
number of bars
indicates the
performance of the
device.
It shows the
frequency
bands’
real-time
working
performance.
When it flashes, it
indicates that the
device is not working
correctly due to
loopback or overload.
You can refer to "4
regualr problems and 1
normal status" in the
latter part of this
guide to solve
corresponding problems.
No drilled hole
Alarm

02
Booster Light Patterns
Bands contained in the Gauges
LED Type LED condition Remark
Gauge Band Uplink Downlink
LTE700
CELL800
PCS1900
AWS2100 4 1710-1755MHz 2110-2155MHz
12/17 698-716MHz 728-746MHz
13 776-787MHz 746-757MHz
5 824-849MHz 869-894MHz
25/2 1850-1915MHz 1930-1995MHz
On Successfully connected to Bluetooth
OFF
OFF
OFF
OFF
Flashing
Bluetooth is not connected
On
Solid Red
Solid Green
Successfully connected to Wi-Fi
Wi-Fi is not connected
Normal operating condition
Booster is working abnormally
Booster is not receving power from DC power supply
Booster is working normally
Booster is working abnormally
Bluetooth
Wi-Fi
Power
Alarm
Please focus on the gauge that contains the band you are using.
Step 1
Connect the Power Supply to the Booster
Signal BoosterPower Supply
Step 2
Connect the Booster with the App
Getting Started
Register an ID rst and log in.
Add the booster to the device list

Download NetWork Cell Info Lite in the Google store and open it.
It can be seen from the example picture that the frequency band is band 13.
(According to the form before, you need to pay attention to Gauge LTE700)
Then click MAP. You can see your phone connecting to a tower, and you can try aiming your outdoor
antenna at it. But sometimes this is not accurate. You could also move to Step 3.2 to nd the tower
Note: Please take screenshots at this stage.
03
Step 3
Find the cell tower & Determine the outdoor antenna’s position
3.1 Find the band you are using
For Android

04
(1)Dial *3001#12345#*
(2)Follow the instructions, take the screenshots as required.
(1) Enter cellmapper.net
(2) Choose your own carrier and band here.
3.2 Find the cell tower
For ios

05
(3) Then enter the coordinate of where you are trying to install the signal booster, and press Enter key.
(In fact when you open Cellmapper, the map on the right will automatically locate your area if you've given
the site permission to access your location. If you found tower sites not even displayed on the map, it might
because the app intercepts the locations for security reasons.)
(4) After the map jumps to the location, you can scroll the mouse pulley and zoom it out, then you will see the
tower near the location. It would be better to take a screenshot of this page to guide the following installing
steps. Should you have any questions, please contact our tech support.
Note: If you need help nding the tower, please contact our tech support and provide your carrier, band
and screenshots taken in the last steps.

06
Step 4
Connect the outdoor antenna with the booster
3.3 Determine the outdoor antenna’ s position
The outdoor antenna is usually placed at one of the 4 ends of the roof.
Please choose the position according to the tower’ s location. Make sure there are no barriers between the
antenna and the tower.
Note：At this stage, don’ t connect the indoor antenna to the booster.
Outdoor Antenna Outdoor Cable Through-Window Cable
32.8ft NM-SMAM SMA-Male to SMA-Fmale
(No drilled hole)
16.4ft SMAF-SMAM
Outdoor cable to Booster Booster

07
Step 5
Adjust and x the Outdoor Antenna
Step 6
Connect the indoor antenna with the booster
Step 7
Adjust the indoor antenna
Have your outdoor antenna pointed to the cell tower you
found before and observe the reading on the app. Adjust the
outdoor antenna accordingly.
Notes:
(1) The output power should be the higher the better.
(2) The full output power for Sidekick is 10dBm. And the full
gain is 62dB.
Indoor port
Indoor Whip Antenna
(omnidirectional)
Place the signal booster on a table and make sure the booster
is within the coverage area.
Make sure that the gain reaches about 60dB. If not, please
increase the vertical and horizontal distance between the
two antennas or add some barriers.

08
OVERLOAD
DL GAIN OUTPUT POWER REASON SOLUTIONLED LIGHT PATTERN
<60dB >=8dBm
Outdoor signal is too strong
<60dB
<60dB
<60dB
>=8dBm
>=8dBm
>=8dBm
LTE700
CELL800
PCS1900
AWS2100
4 Regular Problems and 1 normal status
Iftheboosterisworkingnormally,nofurtheradjustmentisrequired
Step 8
Signal quality test
You could do the following:
(1)First make sure the signal gauge value is unchanged from that during the outdoor
antenna installation.
(2)Do speed tests with the booster on and o, and make a comparison.
(3)Check if the number of signal bars increases.
(4)Make a phone call or send messages and check if the voice and streaming are better.
Have your outdoor antenna
pointed slightly away from the cell
tower
Alarm light ashing and
Power light solid red
LOOP BACK
DL GAIN OUTPUT POWER REASON SOLUTIONLED LIGHT PATTERN
<60dB <8dBm
<8dBm
<8dBm
<8dBm
<60dB
<60dB
<60dB
LTE700
CELL800
PCS1900
AWS2100
1、Increase vertical and horizontal
distance.
2、Add barriers(e.g. walls)
Please try these solutions until the
gain reaches or is over 60dB.
Alarm light ashing and
Power light solid
red(strong loop back) or
green(slight loop back)
Inadequate separation of
the indoor and outdoor
antennas
POOR SIGNAL
DL GAIN OUTPUT POWER REASON SOLUTIONLED LIGHT PATTERN
>=60dB
>=60dB
>=60dB
>=60dB
--/NEGATIVE
--/NEGATIVE
--/NEGATIVE
--/NEGATIVE
LTE700
CELL800
PCS1900
AWS2100
1、Try adjusting the outdoor
antenna to the best direction
2、Try adjusting the outdoor
antenna to another cell tower
3、Try increasing the height of the
outdoor antenna and make sure
there are no barriers between the
tower and the outdoor antenna
Please try these solutions until the
output power reaches or is over
-5dBm.
Alarm light OFF and
power light solid green Input signal is too weak


Note:
Some customers have some misunderstandings about boosters, and we would like to clarify it here：
If you can't even get a stable 1 bar outside the house or on the roof, then we suggest you return it as it won't
work in areas with very weak signal, the same is true of all boosters on the market.

Technical Specications
NORMAL
DL GAIN OUTPUT POWER REASON SOLUTIONLED LIGHT PATTERN
>=60dB
>=60dB
>=60dB
>=60dB
>=-5dBm
>=-5dBm
>=-5dBm
>=-5dBm
LTE700
CELL800
PCS1900
AWS2100
Alarm light OFF and
power light solid green
Normal but No Boosted Signal
DL GAIN OUTPUT POWER REASON SOLUTIONLED LIGHT PATTERN
>=60dB
>=60dB
>=60dB
>=60dB
>=-5dBm
>=-5dBm
>=-5dBm
>=-5dBm
LTE700
CELL800
PCS1900
AWS2100
Check the band you are using again.
If it stays at band66, get into the
'detail'/ 'Setting' of gagues on Signal
Supervisor and switch o RF switch
of AWS2100, then adjust the
outdoor antenna again. It would be
better if there are two persons and
one can stay near the indoor
antenna to check if the signal is
boosted.
Alarm light OFF and
power light solid green
1、The band is not
supported
2、The Signal is from
other Carriers
09
Working Band
UL F requency R ange(MHz)
DL F requency R ange(MHz)
Supported Standar ds
Max. Gain
Max. output power
MGC (Step Attenuation )
I/O P ort
Impedance
Environment Conditions
Dimensions
Weight
Power Supply
698-716 / 776 – 787 / 824-849 / 1850-1915 / 1710-1755
728-746 / 746 – 757 / 869-894 / 1930-1995 / 2110-2155
Band 12-17 / Band 13 / Band 5 / Band 25-2 / Band 4
62 dB
DL 10 dBm
≥ 25 dB / 1 dB step
50 ohm
IP40
7.6*5*1.3 in / 192*126*33mm
≤ 1.68 lbs / 0.76 kg
Input A C100~240 V , 50/60 Hz, Output DC 12 V / 3 A
65 dB
DL 12 dBm
CDMA , WCDMA , GSM, EDGE, HSPA+, EVDO, L , TE
and all cellular standards
Sidekick
Model No. Hero
5G
SMA-Female

Download Signal Supervisor or enter our website.
a. You can download the specic user manual.
b. You can reach our technical support for help.
For more information
www.hiboost.com.
10

3150 Premier Drive,Suite 130,
Irving, TX 75063
[phone]
[email protected]
www.hiboost.com