HiBoost Smartlink Series User manual

Smartlink Series
Installation Guide

Step 2
Download the Signal Supervisor App, register ID and
booster.
Package Contents
Signal Booster Outdoor Cable Indoor Antenna
Outdoor Cable
Connect the Power Supply and the whip antenna to the Booster
Step 1
Outside Antenna
Power Supply 3M waterproof tape Accessories for main parts
Getting Started
Register an ID first and log in.
Add the booster to the device list.
10k Smartlink
01
are all provided to protect connections SMA-Male to SMA-Female
Bluetooth and
Wi-Fi antenna
Through-Window Cable
(No drilled hole)
32.8ft NM-SMAM 16.4ft SMAF-NM 30ft NM-NM
Indoor Cable

Download NetWork Cell Info Lite in the Google store and open it.
It can be seen that the frequency band is band 13 from the example picture.
Then click MAP. You can see your phone connecting to a tower, and you can try aiming your outdoor
antenna at it. But sometimes this is not accurate.You could also follow Step 3.2 to find the tower.
Note: Please take screenshots at this stage.
Step 3
Find the cell tower & Determine the outdoor antenna’s position
3.1 Find the b and you are using
(1)Dial *3001#12345#*
(2)Follow the instructions, take the screenshots as requested
02
For Android
For ios

(1)Enter cellmapper.net
(2)Choose your own carrier and band here.
(3) Then enter the coordinate of where you are trying to
install the signal booster, and press Enter key.
(In fact when you open Cellmapper, the map on the right will automatically locate your area if you've given the site
permission to access your location. If you found tower sites that were not even showing up on the map, it may because
the app offsets the locations for security reasons.)
(4) The map on your right will jump to the location, then you can scroll the
mouse pulley, zoom it out, you will see the tower near the location. And
better to take a screenshot of this page for guiding the following installing
steps. If you have any questions, please contact our tech support.
Note: If you need help finding the tower, please contact our tech support
and provide your carrier, band and screenshots taken in the last steps.
The outdoor antenna is usually placed at one of the 4 ends of the roof.
Please choose the position according to the tower’s location. Make sure
there are no barriers between the antenna and the tower.
3.2 Find the cell tower
3.3 Determine the outdoor antenna’s position
03

Have your outdoor antenna pointed to the cell tower you found before
and watch the readings on the app. Adjust the outdoor antenna.
Notes:
(1) The output power should be the higher the better.
(2) The full output power for 10k Smartlink is 12dBm. And the full gain is 65dB.
04
Note：At this stage, don’t connect the indoor antenna to the booster.
Step 4
Connect the outdoor antenna with the booster
Step 5
Adjust and fix the Outdoor Antenna
Step 6
Connect the indoor antenna with the booster
32.8
Indoor Antennna NF
Indoor Cable
30ft NM-NM

05
Step 7
Adjust the indoor antenna
Step 8
Signal quality test
Have your indoor antenna pointed to the area you
would like to cover with signal.
Notes:
(1)It would be best if you could make the two antennas
face opposite directions.
(2)Make sure that the gain reaches 65dB. If not, please
adjust the direction of the indoor antenna/increase the
vertical and horizontal distance between the two
antennas/add some barriers.
You could do the following:
(1)Do speed tests with the booster on and off, and make a comparison.
(2)Check if the number of signal bars increases.
(3)Make a phone call or send messages and check if the voice and streaming are better.
65dB

06
Step 9
Fix the Inside Antenna and the Booster
Fix the booster with the provided expansion bolt and hook.
(UL)Gain (DL)Gain (DL)Output
Power
LED Light
Indicator Reason Method
<65dB <65dB >=12dBm
<65dB <65dB <12dBm
=65dB =65dB
--
=65dB =65dB Positive
Overload
Loop Back
Poor Input
Signal
Normal but
No Boosted
Signal
Normal =65dB =65dB Positive
Have your outdoor antenna
pointed slightly off the cell tower
Try adjusting the outdoor antenna or using
another cell tower
Try adjusting the outdoor antenna again. It
would be better if there are two persons
and one can stay near the indoor antenna
to check if the signal is boosted.
Alarm
and ISO
lights both
solid green
The Signal is
from Other
Bands or
Carriers
Outdoor
Signal Too
Weak
Separation
of the Two
Antennas
Not Good
Enough
ISO light
blinking
green or
red
Alarm light
blinking
green or
red
Outdoor
Signal Too
Strong
Alarm
and ISO
lights both
solid
green
1、Increase vertical and horizontal distance.
2、Make them face in different directions.
3、Add barriers
4 Regular Problems and 1 normal status
Fix the indoor antenna with the provided expansion bolt and hook.

07
Gauge Band Uplink Downlink
12/17 698-716MHz 728-746MHz
13 776-787MHz 746-757MHz
CELL800 5 824-849MHz 869-894MHz
PCS1900 25/2 1850-1915MHz 1930-1995MHz
AWS2100 4 1710-1755MHz 2110-2155MHz
LTE700
Note:

Some customers have some misunderstandings about boosters, and we would like to clarify it here.
If you can't even get a stable 1 bar outside the house or on the roof, then we suggest you return it as it won't work in areas
with very weak signal, the same is true of all boosters on the market.
Bands contained in the Gauges
Booster Light Patterns

08
Download Signal Supervisor or enter our website.
a. You can download the specific user manual.
b. You can reach our technical support for help.
For more information
www.hiboost.com.
Working Bands
UL Frequency Range
DL Frequency Range
Maximum Gain
Maximum Output Power
I/O Port
Weight
Dimensions
MGC(Step Attenuation) >25 dB /1 dB Step
> 4.0 lb / 1.8 kg
4.7in x 7.8in x1.4in /
120mm x 198mm x 34mm
8.6in x 6.5in x 2in /
218mm x 165mm x 50mm
> 5.0 lb / 2.2 kg
Impedance
Environment Condition
Power Supply Input AC 100~240V, 50/60Hz, Output DC 12 V/3 A
50 ohm
IP40
728-746 / 746-757 / 869-894 / 1930-1995 / 2110-2155
Band 12/17/Band 13/Band 5/Band 25/2/Band 4
698-716 / 776-787 / 824-849 / 1850-1915 / 1710-1755
60 dB
UL 24 dBm, DL 10 dBm
N-Female & SMA-Female
65 dB 72 dB
UL 24 dBm, DL 12 dBm
4K Smart Link
Model No. 10K Smart Link 15K Smart Link
Technical Specifications

3150 Premier Drive,Suite 130,
Irving, TX 75063
[phone]
ser[email protected]
www.hiboost.com
www.hiboost.com.