HiBoost Home 4K User manual

‘
‘.-\\
”FBDDST Boost Your Bars
C]
User
Manual
—
Home
4K
Mobile
Signal
Booster

‘2“
111130051"
CO N T E N T
WHAT'S INCLUDED .................................................................................................... 3
HOW IT WORKS ........................................................................................................ 4
HOW TO INSTALL YOUR SIGNAL BOOSTER ........................................................... 4
1.1 Overview ........................................................................................................ 4
12 Installation preparation .................................................................................. 5
1.5 How to find the location with the strongest received signal ----------------------- 5
1.4 Install Outdoor Antenna ................................................................................ 7
1.5 Install Indoor Antenna ................................................................................... 7
1.6 Install Signal Booster ..................................................................................... 8
1.7 Run coaxial cable ......................................................................................... 8
18 Power Up your the Signal Booster ................................................................. 9
SIGNAL BOOSTER STATUS ........................................................................................ 9
LCD FtUreS ........................................................................................................ 10
LED StCItUS ............................................................................................................ 11
Control Buttons Operation .................................................................................. 11
Manual Gain Control (mgc) ............................................................................... 12
TROUBLESHOOTING ............................................................................................... 13
AUTHORIZED KITTING OPTIONS ............................................................................. 14
FCC RF EXPOSURE STATEMENT ............................................................................... 15
WARNING AND STATEMENT .................................................................................... 15
SPECIFICATIONS ...................................................................................................... 17
PRODUCT WARRANTY .............................................................................................. 18
2/18

WHAT IS INCLUDED
Home
4K
Outdoor
Wide
Band
Indoor
Wide
Band
PanelAntenna PanelAntenna
j;
1’”
12V/3A
Pole
and
Wall
AC/DC
Power
Supply
MountBracket
Wall
MountBracket
2
30
feet
H'BOOStZOO
Booster
Mount
Hardware
Low—loss
Cable
We provide
all accessories
needed
for the
signal
booster.
For more
information
please
visit
www.hiboostusa.com.
Warning:
Unauthorized
antennas,
cables,
and/or
coupling
devices
are prohibited
by new
FCC
rules.
Please
contact
FCC
for details:
1-888—CALL-FCC.
3/18

‘2“
111130051"
HOW IT WORKS
The HiBoost Home 4K signdl booster is designed to help mobile users improve
signal in homes, offices, and other areas where cellulqr signal is weak or
unreliable. The outdoor ontennq receives the signal from the nearest cellulor
tower, omplifies it, and transmits to the signal booster. Then the indoor ontenno
will receive the signal and retrdnsmit it to your mobile device. The signals
produced by your phone are also amplified by the indoor ontennd via the
booster and outdoor ontenno.
This manual provides simple installation instructions that will have your signol
booster kit running in record time.
HOW TO INSTALL YOUR SIGNAL BOOSTER
1.1 Overview
This manual will help you properly install your signal booster kit. It is important to
read through all of the installation steps before installing your equipment.
Thoroughly read through the instructions, visuolize where all the equipment will
need to be installed and do 0 soft installation by placing the devices where they
need to be before mounting any equipment.
0 Home 4K Signol Booster 9 Outdoor Wide Bond Ponel Antenna
9 Indoor Wide Bond Pdnel Antenna 0 30ft HiBoostZOO Low-loss Cdble
612V/ 3A, AC/DC Power Supply
4/18

1.2 Installation Preparation
Before you install
- Make sure you have sufficient cable length between the proposed
outdoor/indoor antenna location and booster connector.
- Make sure the position you install the booster is near to an existing electrical
outlet, well ventilated, and away from excessive heat, moisture, and direct
sunlight.
Tools Required
Hillips Screwdriver Drill Mobile Phone
Before you get started, you will need to plan the layout of your system. This
involves finding the location with the strongest received signal from the cellular
tower, as well as antenna, booster, and cable placement.
General installation steps:
1. Find the strongest received signal for the location of the outdoor antenna.
2. Install the outdoor antenna on the roof to obtain the strongest downlink
signal from the local cellular towers.
5. Install the indoor antennas where you want to improve the signal level.
4. Mount the amplifier, connect the cables from the outdoor antenna and indoor
antenna at the designated ports, and connect the booster to the AC supply
(make sure all the cables are connected before applying power).
1.3 How to find the location with the strongest received signal
The outdoor signal strength the booster receives directly affects the efficiency of
the indoor coverage. That is why it is crucially important to install the antenna at
a good location and point it properly towards a tower where signal reception is
the strongest.
There are many methods that can be used to find the strongest signal from the
cellular towers. One is to use the LCD display on the booster that shows the
downlink power output of the booster in each band, the other is to use a mobile
phone or mobile phone app to test signal strength, and the third is to use a
commercially available signal strength meter.
5/18

‘2“
111130051"
We highly recommend that you use the LCD display on the booster US this
method is generally more convenient. However, in situations where the desired
corrier’s signal is much weaker than the other local signals, using 0 mobile
phone, opp or signal level meter can be 0 more accurate method of homing in
on the best signal for installation.
. LCD Display Method
Connect the outdoor antenna to the booster’s outdoor port. Fix the outdoor
antenna on the roof of the building and point it to the nearest cell tower. Then
have 0 look at the gain and output power value displayed on the dmplifier’s
LCD.
The outdoor ontenno receives the strongest signal when the booster's downlink
output power reaches its highest level in each bond. If the LCD shows moximum
gain and power, and there are not any oldrms (no ISO, ALC, OFF legend
flashing and no quick floshing green or red in LEDs), it means the present
location is the best for ensuring that the booster hos moximized performance.
The maximum downlink power for Home 4K is 10dBm, and the maximum
downlink gain is 60dB.
Note: These showed values may vary dynomicolly at times between 1-3 dB
which is normal due to outdoor signol conditions.
. Mobile Phone Method
You can use Cl telephone to test signal strength on the top of the building. The
number of bars on the network indicotor will define opproximdte strength of the
received signal. Normally the roof of the building is the best place to receive the
strongest signol. As shown on the drawing below, you need to test the signal in
the points from A to E, and select the location with the best signal strength for
outdoor installation. It is recommended to use 0 mobile opp that can display in 0
6/18

test mode the signal level in dBm units. It is more accurate than checking the
signal bars. For more details refer to http://blog.hiboostusa.com/signal-strength-
measure-instructions/.
Note: Please try to receive a signal from cell towers that are not overloaded with
multiple users. This can be estimated by the population density in the area
served by the tower. For example, it is recommended to avoid cell towers near
supermarkets, shopping malls, stadiums or any other public places visited by
many people regularly. This will help maintain reliable phone call connections
and higher speed data services.
Mark the strongest received signal as the installation location and direction for
the outdoor antenna.
1.4 Install Outdoor Antenna
Install the outdoor antenna at the the location with the strongest received signal.
IMPORTANT: Testing the signal 5 times in the desired location for installing the
outdoor antenna will help ensure the most smooth and stable phone calls and
data transmission.
1 to 2 inch
diameter pole
9
bracket U-bolt
Note: Be sure the cradle is at the desired height and rotated toward the
strongest cellular signal before tightening the nuts. Do not over tighten.
1.5 Install Indoor Antenna
Select a place on a wall in the area where you need better reception.
Mount the indoor antenna with the included screws as shown in the figure
below.
7/18

‘2“
111130051"
W
>\ slide into mount
tapping
screw
hanging
folder>\<
plastic expansion
bolt
1.6 Install your signal booster
The signal booster should be mounted in an easily accessible area so it's easy to
perform general maintenance. The optimal area would be on a wall located
near a power outlet. Please use a surge protector rated at a minimum of 1000
Joules between the amplifier's power adaptor and the AC power outlet on the
wall.
Mount the booster with the included screws as shown in the figure below.
I slide into mount
l
plastic expansion bolt
\l
hanging folder
apping screw
(-0-
1.7 Run coaxial cable
Loosely run the supplied coaxial cable from your outdoor antenna to your
booster connector marked ”Outdoor”. We recommend applying silicone
caulking to fully waterproof the connection.
Connect the indoor antenna cables from your indoor antenna to the booster
connector marked ”Indoor”. Tighten the connection by hand.
(After you have tested the system you can permanently secure the coaxial
cable).
8/18

As you route and pull cabling, follow these general guidelines:
. Bend cables and route them smoothly, and protect the outer skin against any
damage.
- Keep horizontol cobles straight and fosten them with or tie every three to five
feet.
. Bind ond fosten verticol cobles every six to eight feet.
- Woterproof oll connectors between outdoor antenna and coaxial cables with
Wrop woterproof tape to ovoid woter or other kinds of damage.
. Be careful when plugging the connector in so as not to damage the center pins
on the connectors.
1.8 Power up your signal booster
Once all the following precoutions have been token, power on the signal
booster.
1. Verify that you have left at least 20 feet of vertical sepdrdtion spoce between
the indoor and outdoor ontennds.
2. Never point the front of outdoor ontenno towards the inside of the indoor
antenna.
5. Verify that the supplied coaxial cables from both the outdoor antenna and the
indoor antenna are properly connected to the signal booster before
powering it up.
4. Carefully plug in the supplied power adaptor into the signal booster where it
is marked 'DC 12V' and connect the other end to 0 power outlet.
The LED indicator morked power should light up green.
SIGNAL BOOSTER STATUS
Overview: The booster has 0 very smart stortup system. When you finished the
booster system installation and power on the booster. The booster will start its
initiolizotion process to check the received downlink signal from the cell site and
the isolation status, on automatic process designed to ensure its best
performance. This will take approximately 3 - 5 seconds.
After the booster starts up, please check if the coverage is good. If it is good, the
booster system installation is complete. If the coverage is not adequate, pleose
fully rereod and understand the LCD, LED indicotions, control buttons and MGC
function on your booster, as they will help you identify and solve any potential
Issues.
9/18

J
HFBOUST
- LCD Features
Working Uplink Downlink Downlink
Frequency Gain Gain Output
Power
Relative signal
power from tower Alarm
status Indicator 0
.
Powe
Indicates
DC
0
power status
ISO
Antenna Isolation
Status
Indicator
Band
Shut
Off
Indicator
Automatic Level Control
(ALC)Activity Indicator
(0 o
o)
G)
SET
F
DEC-
|NC+
Band: Shows the working
frequency bands
where the amplifier
is operating.
UL/DL: Shows real-time
uplink and downlink
gain(dB). These values
will change
slightly as the ALC
or ISO makes changes
to the gain to optimize
coverage.
Power: Shows real-time
downlink power(dBm)
that the amplifier
is delivering to
the indoor antenna
port. When the amplifier
DL output power is
lower than -
IOdBm, the value
will display "---”.
ISO: When the system
does not have enough
isolation between
the outdoor and
indoor antennas,
the ”ISO" indicator
will be flashing showing
that the ISO has
lowered the gain
in some bands to
keep the system from
oscillating. Press the
"SET” key and the
LCD screen will display
”ISO" value showing
the current band
or bands affected.
ALC flash
L
ALC: When the booster
is receiving too much
DL power from the
tower and the
DL amplifier output
is close to saturating,
the ”ALC" indicators
will flash showing
that the ALC has
lowered the gain
to prevent this overload
condition. Press the
"SET" button and
the screen will show
the band or bands
affected.
I80 flash
Band
LTE7BB
CellBEB
P081900
AHSZlDB

OFF: In some rare situations the ALC or ISO will not be able to compensate for an
oscillation condition or a downlink overload. When this happens the booster will
shut off in the affected band and the LCD ”OFF” indicator will flash. Pressing the
”SET" button will display which band or bands are affected.
. LED Status
LED
Power LED
Alarm LED
ISO LED
Status
Green
Off
Green
Slow Flashing
Green
Quick Flashing
Green
Quick Flashing
Red
Green
Slow Flashing
Green
Quick Flashing
Green
Quick Flashing
Red
Definition
Normal
DC power problem
Output power is
not maximum.
Full output power.
Output power is too high.
The booster automatically
shuts off for protection from
excessive downlink signal
from tower.
Check coverage, leave
as is if it's good; if the
coverage is poor,
please check the
Troubleshooting section
to get solutions.
Not working properly.
Please check the
Troubleshooting section
to get solutions.
No loopback or no self-oscillation. Working properly.
Slight loop back or self-oscillation.
Deep loop back or
self-oscillation.
The booster automatically
shuts off for protection due
to very severe self-oscillation.
Control
Buttons
Operation
Not working properly.
Please check the
Troubleshooting section
to get solutions.
When the LCD is in the fixed display mode, Press the ”SET" key for 3 seconds and
it will start up in the Gain Setting Mode. Press the ”SET" key for 3 seconds, and
11/18

‘2“
111130051"
the LCD will return to the fixed display mode. (For more details refer to Manual
Gain Control (MGC) below.
When the LCD is in the alarm display mode, press the ”SET" key and the LCD
screen will display the alarm indication showing the affected band. Pressing the
”|NC+” (or ”DEC-”) key and the LCD will switch to help tips. If none of keys are
depressed within 50 seconds, the display will return to the fixed display mode.
If none of the control keys are depressed within 5 minutes, the LCD screen will
turn off. Pressing any key will return the display to the fixed mode.
Manual Gain Control (MGC)
Since the booster has a self-adaptive smart automatic level control (ALC) and
isolation gain processing (ISO), most of the time manual adjustments are not
required to achieve good coverage. However, in some cases where the ALC or
ISO is working at a very high rate to adjust the gain and the Alarm or ISO LED is
flashing more than once a second a manual adjustment might be desired.
When the LCD is in the fixed display mode, press the ”SET" key for more than 3
seconds. It will go into the ”Gain Setting Mode" and make one of the gain
values start to blink.
. Press ”SET” key shortly, and the LCD will switch to the next gain value and it will
start to blink. (Uplink or downlink gain for a different band).
- Press ”|NC+” key once shortly and the gain will increase by 1dB, Press ”DEC-”
once shortly and the gain value will be reduced by 1dB.
- Press the ”SET" key for 3 seconds, and the LCD will return to the fixed display
mode.
Actual Gain display MGC Setting Gain
._.
oxoxoxoxcLo
3
03
Ill
3 D.
SSSSwl—
Actual Power
display
NI-‘ODN
I—‘KOSGJ
(98539
(38
axoxOxonlc
m
sssswl—
m
oxoxoxoxmr:
w
sssswl—
rn
000101110
""
(Sis-0000m—
HHmt
88
no:
3
23
Note:
When
adjusting
the gain
manually,
please
ensure
that the
uplink
gain is
equal
to or
not 5
dB less
than the
downlink
gain setting.
This avoids
interference
with the
local
cell site
tower
network.
12/18

TROUBLESHOOTING
Eliminate Flashing ISO legend and Quick Flashing Green, Quick Flashing Red ISO
LED problems:
1. Adjust the outdoor antenna direction, keeping it away from indoor antenna.
Restart booster.
2. Increase the vertical or horizontal distance between the outdoor antenna and
indoor antenna. Restart booster.
3. Use barriers such as walls to increase the isolation.
4. Change the indoor antenna type to an antenna with a more directional
antenna pattern. Orient the indoor antenna and outdoor antenna so they
point in opposite directions.
5. Reduce the booster’s downlink gain using the manual gain controls. Keep
the uplink gain value and downlink gain value the same then restart the
booster.
Note: Uplink gain must be equal to or not less than 5dB below the downlink gain,
to avoid interference with the local carrier’s cell site network.
Target: The ISO issues are solved when the ISO LED is "Green" or "Slow Flashing
Green" or no flashing ISO legend.
Eliminate Flashing ALC legend and Quick Flashing Green, Quick Flashing Red Alarm
LED problems:
1. Adjust the antennas’ directions or locations to lower downlink received signal
level.
2. Slowly reduce the downlink gain using the Manual Gain Controls.
3. If the above methods don't work, reduce the booster's gain with an external
attenuator in line with the outdoor antenna or replace with lower gain
antenna.
Target: The overload issues are fixed when the Alarm LED is "Green" or "Slow
Flashing Green" or no flashing ALC legend. Please note that a "Green" LED
indication may result in smaller coverage area. This can be improved by
adjusting the outdoor antenna to receive a stronger signal.
Eliminate Power legend on LCD and poor coverage problems when Alarm LED
is Green:
1. If the signal has not been improved, please check below:
- The weak downlink signal leads to the low output signal level. Change the
direction or position of the outdoor antenna. You may also try replacing the
outdoor antenna with a higher gain antenna to increase the incoming signal.
- Check to see if it is necessary to add more indoor antennas. Barriers such as
walls can block the signal indoors. You should also check the booster to make
sure the power is maximized. Try installing more indoor antennas or replace
the amplifier with a higher powered one.
2. If the signal in a small section of the building hasn't been improved, try the
13/18

J)
[3005
T
following:
- Check to see if the indoor antenna is installed correctly. Try moving the
antenna to improve coveroge.
- Try adjusting the direction the indoor antenna is pointing.
AUTHORIZED KITTING OPTIONS
The following accessories are authorized by the FCC to be used with the Home
4K Signol Booster.
Outdoor Antenna & Cable Kit Options
Kit 9-5050
Yagi 9dbi Antenna & 50’ 5D Cable
Kit 11-100400
Yagi 11dbi Antenna & 100' 400 Cable
Kit 11-7550
Yagi 11dbi Antenna & 75' 5D Cable
Kit 11-100500
Yagi 11dbi Antenna & 100' 5D Cable
Kit 10-3050
Panel 10dbi Antenna & 30' 5D Cable
Kit 10-50400
Panel 10dbi Antenna & 50' 400 Cable
Kit 10-5050
Panel 10dbi Antenna & 50' 5D Cable
Kit 10-75400
Panel 10dbi Antenna & 75' 400 Cable
Kit 10-100400
Panel 10dbi Antenna & 100' 400 Cable
Kit 10-7550
Panel 10dbi Antenna & 75' 5D Cable
Kit 10-10050
Panel 10dbi Antenna & 100' 5D Cable
Kit 9—50400
Yagi 9dbi Antenna & 50' 400 Cable
Kit 9—75400
Yagi 9dbi Antenna & 75' 400 Cable
Kit 9-100400
Yagi 9dbi Antenna & 100' 400 Cable
Kit 9-7550
Yagi 9dbi Antenna & 75' 5D Cable
Kit 9-10050
Yagi 9dbi Antenna & 100' 5D Cable
Kit 7-3050
Panel 7dbi Antenna & 30' 5D Cable
Kit 7-50400
Panel 7dbi Antenna & 50' 400 Cable
Kit 7-5050
Panel 7dbi Antenna & 50' 5D Cable
Kit 7-75400
Panel 7dbi Antenna & 75' 400 Cable
Kit 7-100400
Panel 7dbi Antenna & 100' 400 Cable
Indoor Antenna & Cable Kit Options
Kit 72-5050-50
2 Panel 7dbi Antenna with50' 5D N male
& 2-Way Splitter
Kit 52-5050-50
2 Whip 5dbi Antenna &50' 5D Cable
& 2-Way Splitter
Kit 102-5050-50
2 Panel 10dbi Antenna with50' 5D N male
& 2-Way Splitter
Kit 103-7550-50
3 Panel 10dbi Antenna & 75' 5D Cable
& 3-Way Splitter
kit 104-7550-50
4 Panel 10dbi Antenna & 75' 5D Cable
& 3 2-Way Splitter
Kit 73-7550-50
3 Panel 7dbi Antenna & 75' 5D Cable
& 3-Way Splitter
kit 74-7550-50
4 Panel 7dbi Antenna & 75' 5D Cable
& 3 2-Way Splitter
Kit 3-30400
Omni 3dBi Antenna with 30' 400 Cable
Kit 3-5050
Omni 3dBi Antenna & 50' 5D Cable
Kit 3-7550
Omni 3dBi Antenna & 75' 5D Cable
Kit 3-10050
Omni 3dBi Antenna & 100' 5D Cable
14/18
Kit 7-7550
Panel 7dbi Antenna & 75' 5D Cable
Kit 7-10050
Panel 7dbi Antenna & 100' 5D Cable
Kit 5-30400
Omni 5dbi Antenna & 30' 400 Cable
Kit 5-3050
Omni 5dbi Antenna & 30' 5D Cable
Kit 5-50400
Omni 5dbi Antenna & 50' 400 Cable
Kit 5-5050
Omni 5dbi Antenna & 50' 5D Cable
Kit 5-75400
Omni 5dbi Antenna & 75' 400 Cable
Kit 5-10400
Omni 5dbi Antenna & 100' 400 Cable
Kit 5-7550
Omni 5dbi Antenna & 75' 5D Cable
Kit 5-10050
Omni 5dbi Antenna & 100' 5D Cable
Kit 3-30400
Omni 3dBi Antenna with 30' 400 Cable
Kit 3-50400
Omni 3dBi Antenna & 50' 400 Cable
Kit 32-50400-50
2 Omni 3dBi Antenna & 50' 400 Cable
& 2-Way Splitter
Kit 33-50400-50
3 Omni 3dBi Antenna & 50' 400 Cable
& 3-Way Splitter
Kit 34-50400-50
4 Omni 3dBi Antenna &50' 400 Cable
& 3 2-Way Splitter

FCC RF EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instruction for satisfying RF exposure compliance. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter.
WARNING AND STATEMENT
This is a CONSUMER device.
BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless
provider and have your provider's consent. Most wireless providers
consent to the use of signal boosters. Some providers may not consent
to the use of this device on their network. If you are unsure, contact your
provider.
You MUST operate this device with approved antennas and cables as
specified by the manufacturer. Antennas MUST be installed least 20 cm
(8 inches) from any person.
You MUST cease operating this device immediately if requested by the
FCC or a licensed wireless service provider.
WARNING. E911 location information may not be provided or may be
inaccurate for calls served by using this device.
This device may be operated ONLY in a fixed location for in-building
use.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
15/18

J
HFBOUST
- Reorient or relocate the receiving antenna.
. Increase the separation between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
. Consult the dealer or an experienced radio/W technician for help.
Changes or modifications not expressly approved by Huaptec could void the
user's authority to operate the equipment.
Note: For a complete list of antennas and cables approved for use with these
boosters see Authorized Kitting Options page 14.
FCC 27.50(d)(4)Statement: Fixed, mobile, and portable (handheld) stations
operating in the 1710-1755 MHZ band are limited to 1 watt EIRP. Fixed stations
operating in the 1710-1755 MHZ band are limited to a maximum antenna height
of 10 meters above ground.
FURTHER INFORMATION ON SIGNAL BOOSTER END-USE REGISTRATION
The following is currently active contact of US wireless provider for booster
register.
https://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp
https://www.sprint.com/IegaI/fcc_boosters.html
https://www.verizonwireless.com/solutions-and-services/accessories/register-
signal-booster/
https://support.t-mobiIe.com/docs/DOC-9827
https://securec45.securewebsession.com/attsignalbooster.com/
16/18

SPECIFICATION
RF Parameter Uplink Downlink
700MHz Band12/17 698~716MH2 728~746MHZ
700MHz
Band13
776~787MHZ 746~757MHZ
Frequency Range 800MHz Band 824~849MHZ 869~894MHZ
PCSI900
1850~1915MH2
1930~1995MHZ
AWSZ100
1710~1755MHz
2110~2155MH2
700MHz
Band12/17
18MHz
700MHz
Band13
11MHz
Band width Cell800 25MHz
PCSI900
65MHz
AWSZ100 45MHz
Max. Gain 60dB
Max. output power 17~24dBm 10dBm
MGC (Step Attenuation ) > 25dB/1step
Electrical
Parameter
Standard
Power
Supply
Input
AC100~240V.50~60HZ,
Output
DC12V/3A
Input
&
Output
Impedance
50
ohm
Mechanical
Parameter
Standard
I
/0
Port
N-Female
Dimensions
120*198*34mm
Weight
<
1.5Kg
17/18

J
#330051"
PRODUCT WARRANTY
30-Day Money-Back: All HiBoost products are protected by a 30-day money-
back guarantee. If for any reason the performance of any product is not
acceptable, the product may be returned to the reseller with a dated proof of
purchase.
6-Year Warranty HiBoost Signal Boosters and kits are warranted for 6 years.
Customers can choose to return the Signal Boosters and kits directly to the
manufacturer at the purchaser’s expense with a dated proof of purchase and a
Returned Material Authorization (RMA) number supplied by HiBoost.
HiBoost will supply two options: repair or replace. HiBoost will cover the cost of
delivery for the consumers located within the continental US.
This warranty does not apply to any Signal Boosters or kits determined by
HiBoost to have been subjected to misuse, abuse, neglect, or mishandling that
alters or damages physical or electronic properties. Failure to use a surge
protected AC Power Strip with at least a 1000 Joule rating will void your
warranty. Damage caused by lightning is not covered by this warranty.
All HiBoost products that are packaged with other HiBoost accessory products
are intended for resale and used as a single integrated system. Such product
kits are required to be sold to the end users or subsequent reseller as packaged.
RMA numbers may be obtained by contacting Technical Support at 972-870-
5666.
18/18

HiBoost USA
6210 N Belt Line Rd., Ste. 110, Irving, TX 75063
Phone/Fax: [phone]
E-mail: [email protected]
Website: www.hiboostusa.com