HIK VISION DS-K2M0016A User manual

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
1 of 10
Elevator control wiring and simple configuration
（Button mode）
Preparation：
Prepare the following equipment for the test, complete the test and then install
Ds-k2210 Ds-k2m0016 ds-k1106
Step 1: DIP Switch
The DIP switch of the card reader should be decimal 1 or 2.
The DIP switch of Ds-2100 should be decimal 1or 2.
The DIP switch of distributed elevator controller (DS-K2M0016A) is decimal 3-10
The device USES binary dialing codes
If you want to get dialing 3, Dial 1 and 2,if you want to get 4, Dial 3

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
2 of 10
Step2:Wring
Step 3:Installation
Installation of elevator controller and Elevator button connection
controller installation diagram

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
3 of 10
Principle:
Button（The DIP switch of distributed elevator controller (DS-K2M0016A) is decimal 3-
10）： We control the buttons in the elevator, just put the NC and COM into the button
circuit, if the permission is verifiable，the relay will action and you can press the
corresponding button. This part we need use NC and COM, because the NC and COM
is disconnected when the controller with power supply，and it will be the opposite
without power supply in button mode. The advantage of this mechanism is the
controller will release control without power supply ，which can avoid hidden
dangers.
Connect the relay string to the corresponding button

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
4 of 10
Step 3:Configuration
4200 2.6.2.7
1.4200 ConfigurationClick the access control
2.Activate

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
5 of 10
3.Modify net info
4.Add to client
User name：admin
To activate the password, you must check “Export to Group”

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
6 of 10
5.Determine the controller to display online
6.Configuring the correspondence between floor and relay
Drag the right relay to the corresponding floor
Click on the upper right corner after the configuration is completed.
The first number of the right relay is based on the Numerical Value of the dip switch

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
7 of 10
7.Set the delay time for each floor by default to 120s, which can be set to 15s
8.add the staff permission
9.Add a person's card

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
8 of 10
10.Add permissions, check permissions and click on the right direction to click ok
11.When you click ok, you will be prompted to send it, and you can click directly.

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
9 of 10
12.Can also be selected permissions set after clicking all issued (delete permission
first, then issued all permissions, generally after adding new equipment use) or move
issued (group permission to use when there is new change).
Step4 :Validate
I give this card the permission of the first three floors，after swiping card，We can
see the corresponding relay acted by these pictures。

Title:
Elevator control wiring and Simple
configuration（Button mode）
Version:
V2.0
Date:
12/5/2017
Product:
Access Control Device
Page:
10 of 10
First Choice for Security Professionals
HIKVISION Technical Support