Hirschmann RS20 series User manual

RM GUI L2E
Release 8.0 05/2013
Technical Support
https://hirschmann-support.belden.eu.com
Reference Manual
GUI Graphical User Interface
Industrial ETHERNET (Gigabit-)Switch
RS20/RS30/RS40, MS20/MS30

The naming of copyrighted trademarks in this manual, even when not specially indicated, should
not be taken to mean that these names may be considered as free in the sense of the trademark
and tradename protection law and hence that they may be freely used by anyone.
© 2013 Hirschmann Automation and Control GmbH
Manuals and software are protected by copyright. All rights reserved. The copying, reproduction,
translation, conversion into any electronic medium or machine scannable form is not permitted,
either in whole or in part. An exception is the preparation of a backup copy of the software for
your own use. For devices with embedded software, the end-user license agreement on the
enclosed CD/DVD applies.
The performance features described here are binding only if they have been expressly agreed
when the contract was made. This document was produced by Hirschmann Automation and
Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right
to change the contents of this document without prior notice. Hirschmann can give no guarantee
in respect of the correctness or accuracy of the information in this document.
Hirschmann can accept no responsibility for damages, resulting from the use of the network
components or the associated operating software. In addition, we refer to the conditions of use
specified in the license contract.
You can get the latest version of this manual on the Internet at the Hirschmann product site
(www.hirschmann.com).
Printed in Germany
Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany
Tel.: [phone]
Rel. 8.0 - 05/2013 – 30.04.2013

Contents
RM GUI L2E
Release 8.0 05/2013 3
Contents
About this Manual 7
Key 9
Opening the Graphical User Interface 11
1 Basic Settings 17
1.1 System 18
1.2 Modules (MS, PowerMICE, MACH102 and MACH4000) 22
1.3 Network 25
1.4 Software 28
1.4.1 View the software versions presenton the device 29
1.4.2 Restoring the Backup Version 29
1.4.3 TFTP Software Update 29
1.4.4 TFTP Bootcode Update 30
1.4.5 HTTP Software Update 31
1.4.6 Automatic software update by ACA 31
1.5 Port Configuration 32
1.6 Power over ETHERNET 35
1.7 Load/Save 38
1.7.1 Loading a Configuration 39
1.7.2 Saving the Configuration 46
1.7.3 URL 48
1.7.4 Deleting a configuration 49
1.7.5 Using the AutoConfiguration Adapter (ACA) 49
1.7.6 Cancelling a configuration change 51
1.8 Restart 53
2 Security 55
2.1 Password / SNMPv3 access 56
2.2 SNMPv1/v2 Access Settings 59
2.3 Telnet/Web Access 62
2.3.1 Description of Telnet Access 63
2.3.2 Description of Web Access (http) 63

Contents
4RM GUI L2E
Release 8.0 05/2013
2.4 Port Security 65
2.5 Login Banner 71
3 Time 73
3.1 Basic Settings 74
3.2 SNTP configuration 77
3.3 PTP (IEEE 1588) 81
3.3.1 PTP Global (MS20/MS30, PowerMICE, MACH 104,
MACH 1040) 84
3.3.2 PTP Version 1 (MS20/MS30, PowerMICE,
MACH 104, MACH 1040) 88
3.3.3 PTP Version 2 (BC) (MS20/MS30, PowerMICE,
MACH 104, MACH 1040) 90
3.3.4 PTP Version 2 (TC) (MS20/MS30, PowerMICE,
MACH 104, MACH 1040) 97
4 Switching 103
4.1 Switching Global 104
4.2 Filter for MAC addresses 108
4.3 Rate Limiter 111
4.3.1 Rate limiter settings 112
4.4 Multicasts 114
4.4.1 IGMP (Internet Group Management Protocol) 114
4.5 VLAN 121
4.5.1 VLAN Global 121
4.5.2 Current VLAN 125
4.5.3 VLAN Static 127
4.5.4 Port 130
5 QoS/Priority 133
5.1 Global 134
5.2 Port Configuration 138
5.2.1 Entering the port priority 139
5.3 802.1D/p mapping 140
5.4 IP DSCP mapping 142

Contents
RM GUI L2E
Release 8.0 05/2013 5
6 Redundancy 145
6.1 Ring Redundancy 146
6.1.1 Configuring the HIPER-Ring 148
6.1.2 Configuring the MRP-Ring 152
6.2 Ring/Network Coupling 156
6.2.1 Preparing a Ring/Network Coupling 156
6.3 Spanning Tree 162
6.3.1 Global 164
6.3.2 Port 170
7 Diagnostics 179
7.1 Syslog 180
7.2 Trap log 184
7.3 Ports 186
7.3.1 Statistics table 186
7.3.2 Network load (Utilization) 188
7.3.3 SFP Transceiver 190
7.4 Topology Discovery 192
7.4.1 LLDP Information from Neighbor Devices 192
7.5 Port Mirroring 194
7.6 Device Status 197
7.7 Signal contact 200
7.7.1 Manual Setting 200
7.7.2 Function monitoring 201
7.7.3 Device status 202
7.7.4 Configuring Traps 203
7.8 Alarms (Traps) 205
7.9 Report 208
7.9.1 System Information 210
7.9.2 Event Log 211
7.10 IP address conflict detection 212
7.11 MAC Notification 214
7.11.1 Operation 214
7.11.2 Configuration 215
7.11.3 Table 215

Contents
6RM GUI L2E
Release 8.0 05/2013
7.12 Self Test 217
7.13 Service Mode 219
7.13.1 Activating the service mode 220
7.13.2 Deactivating the service mode 222
8 Advanced 223
8.1 DHCP Relay Agent 224
8.2 Industrial Protocols 227
8.2.1 PROFINET 227
8.2.2 EtherNet/IP 230
8.2.3 IEC61850 MMS Protocol (RSR, MACH 1000) 231
8.3 Software DIP Switch overwrite (MICE, PowerMICE and RS) 233
8.4 Command Line 235
A Appendix 237
A.1 Technical Data 238
A.2 List of RFCs 239
A.3 Underlying IEEE Standards 241
A.4 Underlying IEC Norms 242
A.5 Literature references 243
A.6 Copyright of Integrated Software 244
A.6.1 Bouncy Castle Crypto APIs (Java) 244
A.6.2 Broadcom Corporation 245
B Index 247
C Readers’ Comments 249
D Further Support 251

About this Manual
RM GUI L2E
Release 8.0 05/2013 7
About this Manual
The “GUI” reference manual contains detailed information on using the
graphical interface to operate the individual functions of the device.
In the following, the GUI (Graphical User Interface) will be referred as Web-
based Interface.
The “Command Line Interface” reference manual contains detailed
information on using the Command Line Interface to operate the individual
functions of the device.
The “Installation” user manual contains a device description, safety
instructions, a description of the display, and the other information that you
need to install the device.
The “Basic Configuration” user manual contains the information you need to
start operating the device. It takes you step by step from the first startup
operation through to the basic settings for operation in your environment.
The “Redundancy Configuration” user manual document contains the
information you require to select the suitable redundancy procedure and
configure it.
The “Industry Protocols” user manual describes how the device is connected
by means of a communication protocol commonly used in the industry, such
as EtherNet/IP or PROFINET IO.

About this Manual
8RM GUI L2E
Release 8.0 05/2013
The Industrial HiVision Network Management Software provides you with
additional options for smooth configuration and monitoring:
Simultaneous configuration of multiple devices
Graphical user interface with network layout
Auto-topology discovery
Event log
Event handling
Client/server structure
Browser interface
ActiveX control for SCADA integration
SNMP/OPC gateway.
Maintenance
Hirschmann is continually working to improve and develop our software.
You should regularly check whether there is a new version of the software
that provides you with additional benefits. You will find software
information and downloads on the product pages of the Hirschmann
website.

Key
RM GUI L2E
Release 8.0 05/2013 9
Key
The designations used in this manual have the following meanings:
Symbols used:
List
Work step
Subheading
Link Cross-reference with link
Note: A note emphasizes an important fact or draws your attention to a dependency.
Courier ASCII representation in user interface
WLAN access point
Router with firewall
Switch with firewall
Router
Switch
Bridge

Key
10 RM GUI L2E
Release 8.0 05/2013
Hub
A random computer
Configuration Computer
Server
PLC -
Programmable logic
controller
I/O -
Robot

Opening the Graphical User Interface
RM GUI L2E
Release 8.0 05/2013 11
Opening the Graphical User
Interface
To open the graphical user interface, you need a Web browser, for example
Mozilla Firefox version 3.5 or later, or Microsoft Internet Explorer version 6 or
later.
Note: The graphical user interface uses Java 6 or Java 7.
Install the software from the enclosed CD-ROM. To do this, you go to
“Additional Software”, select Java Runtime Environment and click on
“Installation”.

Opening the Graphical User Interface
12 RM GUI L2E
Release 8.0 05/2013
Figure 1: Installing Java
Start your Web browser.
Activate Java in the security settings of your Web browser.
Establish the connection by entering the IP address of the device which
you want to administer via the Web-based management in the address
field of the Web browser. Enter the address in the following form:
http://xxx.xxx.xxx.xxx
The login window appears on the screen.

Opening the Graphical User Interface
RM GUI L2E
Release 8.0 05/2013 13
Figure 2: Login window
Click on OK.
The user interface (Web-based Interface) of the device appears on the
screen.
Note: The changes you make in the dialogs will be copied to the volatile
memory of the device (RAM) when you click “Set”. Click “Reload” to update
the display.
To save any changes made so that they will be retained after a power cycle
or reboot of the device use the save option on the "Load/Save" dialog (see
on page 38 “Load/Save”).

Opening the Graphical User Interface
14 RM GUI L2E
Release 8.0 05/2013
Note: If you enter an incorrect configuration, you may block access to your
device.
Activating the function “Cancel configuration change” in the “Load/Save”
dialog enables you to return automatically to the last configuration after a set
time period has elapsed. This gives you back your access to the device.
Figure 3: User interface (Web-based Interface) of the device with speech-bubble
help

Opening the Graphical User Interface
RM GUI L2E
Release 8.0 05/2013 15
The menu section displays the menu items. By placing the mouse pointer in
the menu section and clicking the alternate mouse button you can use “Back”
to return to a menu item you have already selected, or “Forward” to jump to
a menu item you have already selected.

Opening the Graphical User Interface
16 RM GUI L2E
Release 8.0 05/2013

Basic Settings
RM GUI L2E
Release 8.0 05/2013 17
1 Basic Settings
The Basic Settings menu contains the dialogs, displays and tables for the
basic configuration:
System
Modules
Network
Software
Port configuration
Power over Ethernet
Load/Save
Restart
Note: The graphical user interface uses Java 6 or Java 7.
Install the Software from www.java.com.

Basic Settings
18
1.1 System
RM GUI L2E
Release 8.0 05/2013
1.1 System
The “System“ submenu in the basic settings menu is structured as follows:
Device Status
System data
Device view
Reloading data
Figure 4: "System" Submenu
Device Status
This section of the graphical user interface provides information on the
device status and the alarm states the device has detected.

Basic Settings
RM GUI L2E
Release 8.0 05/2013
1.1 System
19
Figure 5: Device status and alarm display
1 - The symbol displays the device state
2 - Cause of the oldest existing alarm
3 - Start of the oldest existing alarm
System Data
The fields in this frame show operating data and information on the
location of the device.
– the system name,
– the location description,
– the name of the contact person for this device,
– the temperature threshold values.
Name Meaning
Name System name of this device
Location Location of this device
Contact The contact for this device
Basic module Hardware version of the device
Media module 1 Hardware version of media module 1
Media module 2 Hardware version of media module 2
Media module 3 Hardware version of media module 3
Media module 4 Hardware version of media module 4
Media module 5 Hardware version of media module 5
Media module 6 Hardware version of media module 6
Media module 7 Hardware version of media module 7
Power supply (P1/P2) Status of power units (P1/P2)
Uptime Shows the time that has elapsed since this device was last
restarted.
Temperature (°C) Temperature of the device. Lower/upper temperature
threshold values. If the temperature goes outside this range,
the device generates an alarm.
Table 1: System Data
132

Basic Settings
20
1.1 System
RM GUI L2E
Release 8.0 05/2013
Device View
The device view shows the device with the current configuration. The
status of the individual ports is indicated by one of the symbols listed
below. You will get a full description of the port's status by positioning the
mouse pointer over the port's symbol.
Figure 6: Device View
Meaning of the symbols:
The port (10, 100 Mbit/s, 1, 10 Gbit/s) is enabled
and the connection is OK.
The port is disabled by the management
and it has a connection.
The port is disabled by the management
and it has no connection.
The port is in autonegotiation mode.
The port is in HDX mode.
The port (100 MBit/s) is in the discarding mode of a redundancy
protocol such as Spanning Tree or HIPER-Ring.
The port is in routing mode (100 Mbit/s).