Hisense AW-05CR1RUGU10 Technical manual

AW-05CR1RUGU10
AW-06CR1RUFU20
AW-06CR1RVFUE20
AW-08CW1RVFUE20
AW-10CW1RVFUE20
AW-08DR1RVFU20
AW-12CW1RWFUE20
AW-14CW1RWFUE20
INSTRUCCIONES DE INSTALACIÓN Y USO
Modelo:
Model/
Para consultas sobre las características, funcionamiento/ rendimiento,
piezas o servicio, llame al: 1-877-465-3566
AW-08DR1RVFU21
AW-08CW1RVFUE21
AW-12CW1RWFUE21

TABLE OF CONTENTS
4
3
5
6
4
6
6
8
8
12
Annual Maintenance
10
11
11
AIR CONDITIONER SAFETY 2
INSTALLATION REQUIREMENTS 3
Tools and Parts
Electrical Requirements
Location Requirements
INSTALLATION INSTRUCTIONS
Unpack the Air Conditioner
Prepare Air Conditioner for Installation
Window Air Conditioner Installation
Complete Installation
Starting Your Air Conditioner
AIR CONDITIONER USE
Using the Remote Control
Changing Air Direction
Exhaust Air Vent
Normal Sounds
AIR CONDITIONER CARE 12
12
Cleaning the Front Panel 12
Repairing Paint Damage 12
TROUBLESHOOTING
9
Cleaning the Air Filter 12
13
REMOVING AC FROM WINDOW
12
1

2
AIR CONDITIONER SAFETY
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol .
This symbol alerts you to potential hazards that can kill or hurt you and others .
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING " " " ."
These words mean :
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire electrical shock or injury when using your air conditioner follow these basic precautions , , :
SAVE THESE INSTRUCTIONS
Unplug air conditioner before servicing .
Use two or more people to move and install air conditioner.
Plug into a grounded prong outlet 3 .
Do not remove ground prong .
Do not use an adapter.
Do not use an extension cord .
You safety and the safety of others are very important.
Do not use means to accelerate the defrosting process
or to clean, other than those recommended by the
manufacturer.
The appliance shall be stored in a room without
continuously operating ignition sources(for example:
open flames, an operating gas appliance or an
operating electric heater.
Do not pierce or bum refrigerant tubing. Be aware that
refrigerants may not contain an odor.
nameplate on the air conditioner.
The maximum refrigerant charge amount is shown at
damage from occurring.
The appliance shall be stored so as to prevent mechanical
Keep ventilation openings clear of obstruction.
Do not drill holes in the unit.
When handling, installing, and operating the appliance,
care should be taken to avoid damage to the
refrigerant tubing.
Maintenance, cleaning, and service should only be
performed by technicians properly trained and qualified
in the use of flammable refrigerants.
Dispose of air conditioner in accordance with Federal
and Local Regulations. Flammable refrigerants require
special disposal procedures. Contact your local authorities
for the environmentally safe disposal of your air conditioner.
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
Before throwing the device, it is necessary to pull back the battery cells and get rid of them safety for recycling reasons.
When you need to disposal of the unit consult our dealer. If pipes are removed incorrectly, refrigerant may blow out and
please recycle or dispose of the packaging material for product in an environmentally responsible manner.
Never store or ship the air conditioner upside down or sideways to avoid damage to the compressor .
The wiring diagram is shown at nameplate on the air conditioner.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
DISPOSING OF THE UNIT
come into contact with your skin, causing injury. Releasing refrigerant into the atmosphere also damages the environments.

3
Wiring requirement
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
WARNING
fire, or electrical shock.
Recommended Grounding Method
To contact a qualified .electrical installer
It is the customer’s responsibility:
To assure that the electrical installation is
adequate and conforms to the Nation Electrical
Code,ANSI/NFPA 70-last edition,and all local
codes and ordinances.
Copies of the standards listed may be obtained from:
Nation Fire Protection Association
1 Batterymarch Park
Quincy,Ma 02169-7471
www.nfpa.org
This
conditioner is equipped with a power supply cord with a
three-prong grounding plug. The cord must be plugged
into a mating, grounded three-prong outlet, grounded in
accordance with all local codes and ordinances. If a
mating outlet is not available, it is the customer's
responsibility to have a properly grounded three-prong
outlet installed by a qualified electrical installer.
air conditioner must be grounded. This air
NOTE:
Your air conditioner’s device may differ from the one shown.
To test your power supply cord:
1. Plug power supply cord into a grounded 3 prong outlet.
2. Press RESET (on some devices, a green light will turn on).
3. Press TEST (listen for click; Reset button will trip, and on
some devices, a green light will turn off).
4. Press and release RESET (listen for click; Reset button will
latch, and on some devices, a green light will turn on). The
power supply cord is ready for operation.
NOTE:
■The Reset button must be pushed in for proper operation.
■The power supply cord must be replaced if it fails to trip when
the test button is pressed or fails to reset.
■Do not use the power supply cord as an off/on switch. The
power supply cord is designed as a protective device.
■A damaged power supply cord must be replaced with a new
power supply cord obtained from the product manufacturer
and must not be repaired.
■The power supply cord contains no user serviceable parts.
Opening the tamper-resistant case voids all warranty and
performance claims.
A.Test button
B.Reset button
TEST
RESET
A
B
This room air conditioner is equipped with a power supply cord
required by UL. This power supply cord contains state-of-the-art
electronics that sense leakage current. If the cord is crushed, the
electronics detect leakage current and power will be
disconnected in a fraction of a second.
Power Supply Cord
Electrical Requirements
INSTALLATION REQUIREMENTS
Power supply
Model
Time-delay fuse
(or circuit breaker)
115V
103.5V min.
126.5 V max.
5K BTU DOE
6K BTU DOE
10A
13A
12K BTU cooling only
14K BTU cooling only
8K BTU cooling&heating
15A
6K BTU E-star
8K BTU cooling only
10K BTU cooling only

4
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Parts supplied
Check that all parts are included in parts package.
■Phillips screwdriver
■Scissors
■Level
■Tape measure
■Cordless drill and bit
■Pencil
A Adhesive seal (2) .
B Foam seal.
C. lock frame
(for Wooden windows)(2)
I. sash lock
J. EVA foam(2)
D. lock frame
(for Vinyl-Clad windows)(2)
G Side curtains (2).
A
B
CI
J
D
KL
H Top rail.
H
E F
G
1 /8"
E. 3 screws(4) /8"
F. screws(7) 3/4"
Packaging
Remove packaging materials
■ Remove and dispose of/recycle packaging materials.
Remove tape and glue residue from surfaces before turning
on the air conditioner. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
Unpack the Air Conditioner
■Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your air conditioner.
■
■
Handle the air conditioner gently.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
air conditioner .
Failure to do so can result in back or other injury .
Remove top rail from the packaging material.
M
Top Rail
(6K BTU E-star & 8K/10K BTU models)
Top Rail
(5K/6K BTU DOE models)
K. Air conditioner
L. Remote control
M.Sealing sponge
NOTE:
The
H.Top rail、
E. 3/8" screws(4) is not provided for
12K\14K BTU cooling only models.
The J. EVA foam(2) is provided only for E-star models,with
E-star LOGO on the control panel.
The M.Sealing sponge is provided only for 5K\6K BTU DOE
models.

5
Location Requirements
■
■
■
■
■
■
■
■
■
■
Window Installation
If AC is Blocked by Storm Window
Before You Begin
Window opening measurements:
A Cabinet louvers.
A
conditioner is installed.
Add wood as shown, or remove storm window before air.
or slots are not caulked or painted shut. Accumulated rain
water or condensation must be allowed to drain out.
If storm window frame must remain, be sure the drain holes
IMPORTANT:
IMPORTANT:
A
( )With side curtain panels
B
A B
12 2 (315mm) min/5"
15 1 min /5" (386mm)
13 3 (345mm) min /5"
22 (559mm) - 37 4 (960mm)" /5"
24 9 /10" (632mm) - 39 (991mm)"
24 1 - 39 /2" " (622mm) (991mm)
Read these instructions completely and carefully.
Save these instructions for local inspector’s use.
Observe all governing codes and ordinances.
Board
thickness
as required,
for proper
pitch to rear,
along entire
sill. Fasten
with nails or
screws.
Storm window
frame or other
obstruction.
sash
1-1/2"min
(38 mm)
Models
5K BTU DOE
6K BTU DOE
6K BTU E-star
8K BTU
10K BTU
12K BTU
14K BTU
Cooling and Heating models
without Cabinet louvers on top
IMPORTANT: Observe all governing codes and ordinances.
Check the location where air conditioner will be installed. Proper
installation is your responsibility. Make sure you have everything
necessary for correct installation.
The location should provide:
■
Do not use an extension cord.
The appliance shall be installed in accordance with
national wiring regulations.
■ Free movement of air in room to be cooled.
■ A large enough opening for the air conditioner.
NOTE: Cabinet louvers must not be obstructed. Air must be able
to pass through the cabinet louvers freely.
These instructions are for a standard double h- ung
window. You will need to modify them for other
types of windows.
The air conditioner can be installed without the
side curtain panels if needed to fit in a narrow
window. See the window opening dimensions.All
supporting parts must be secured to firm wood,
masonry or metal.
The electrical outlet must be within reach of the
power cord.
Follow the dimensions in the table and
illustration for your model.
Note to Installer:
Be sure to leave these
instructions with the
consumer.
Note to Consumer: Keep these instructions for future
reference.
Skill level: Installation of this appliance requires basic
mechanical skills.
Completion time:
Approximately 1 hour.
We recommend that two people install this product.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty.
You MUST use all supplied parts and use proper
installation procedures as described in these
instructions when installing this air conditioner.

6
INSTALLATION INSTRUCTIONS
Prepare Air Conditioner for Installation
Install Side Curtains
2. Insert top and then bottom of right-hand curtain housing in
top and bottom curtain rails on air conditioner.
Back View
Bottom View
AB
A.Curtain housing
C.Curtain bottom rail on air conditioner
A
C
Attach Top Rail
A Curtain housing.
A Side curtain .
B.Curtain top rail
B. Air conditioner cabinet
A
B
A.
B.Top rail
3 screws /8"
Window Air Conditioner Installation
WARNING
Excessive Weight Hazard
Use two or more people to move and install
air conditioner .
Failure to do so can result in back or other injury .
NOTES:
■Handle air conditioner gently.
■Be sure your air conditioner does not fall out of the opening
during installation or removal.
■Do not block the louvers in the front panel.
■Do not block the louvers on the outside of the air conditioner.
Attach Adhesive Seal
1. Cut the adhesive seal to the width of the lower window sash.
2. Remove the backing from the seal and attach the seal to the
bottom of the lower window sash.
A. Lower window sash
B Adhesive seal.
A
B
1. Locate the bag of screws provided.
2. Place the top rail on the top of the air conditioner cabinet,
lining up the 4 holes in the top rail with the 4 holes on the
top
of the air conditioner cabinet.
3. Using four
3/8"
(10mm) screws, attach the top rail to the
air conditioner cabinet.
NOTE: The top rail had been attached by manufacturer.
(Models: 12K\14K BTU cooling only) 3.
Slide the curtain housing into the channels as far as it could go.
4. Repeat steps above for the left-hand curtain.
NOTE: Attach curtains to the air conditioner before placing the
air conditioner in window.
1.
Slide the Side curtain directly into the cabinet. Slide
the Side curtain down.

7
About 3
Seal
NOTE: Your model may differ from the one shown.
Window Air Conditioner Installation
2. Use a drill bit to drill a starter hole through the (3mm)
hole in the top rail.
1 /8"
Attach Side Curtains to Window
1. Pull the left-hand curtain out until it fits into the window
channel.
3.Insert one of the 3 4 9mm/ " (1 ) screws through the left-hand
curtain and into the window sash.
A
B
C
Measure the inner width
of the side curtain
2. Place the frame lock between the frame
extensions and the window sill with 3/4" (19mm)
screw as shown.
3. To secure lower sash in place, attach right angle
sash lock with 3/4" screw as shown.(19mm)
1. Center air conditioner in window. Lower the window sash
behind the top rail to hold cabinet in place.
Keep a firm grip on the air conditioner, place the unit into
the window opening carefully so the bottom of the air
conditioner frame is against the window sill and make sure
the unit is staying center of the window. Close the window
behind the top rail of the unit carefully.
A. Window sash
B. Hole in side curtain
C.
3/4" screw
NOTE:
The following step 4 and step 5 are only
applicable for E-star models,with E-star LOGO on
the control panel.
4. Put one EVA Foam on the Curtain housing.
In order to minimize air leaks and ensure optimal
insulation, it is necessary to install the EVA Foam on
the Curtain housing.
After the unit is installed to the window, measure
the inner width of the side curtain as shown.

8
Complete Installation
1. Insert foam seal behind the top of the lower window sash and
against the glass of the upper window.
2. Use a drill bit to drill a starter hole through the (3mm)
hole in the top rail.
3. Attach top channel to window sash with one (19mm)
3/4"
1 /8"
screw to secure window in place.
5.Plug into a grounded 3 prong outlet.
6.Press RESET on the power supply cord. See "Electrical
Requirements".
A.Top of lower window sash
B Foam seal.
A
B
Electrical Shock Hazard
Plug into a grounded prong outlet 3 .
Do not remove ground prong .
Do not use an adapter .
Do not use an extension cord .
Failure to follow these instructions can result in death ,
fire or electrical shock, .
WARNING
AIR CONDITIONER USE
best possible results.
This section explains proper air conditioner operation.
IMPORTANT:
■If you turn off the air conditioner, wait at least minutes 3
before turning it back on. This prevents the air conditioner
from blowing a fuse or tripping a circuit breaker.NOTE: In the event of a power failure, your air conditioner will
operate at the previous settings when the power is restored.
Remark a line on the according to less 1/8
(3mm) than the measured width in, then cut the EVA
Foam along the line.
EVA Foam , the side
with should facing the .
Remove the backing from the EVA Foam.
Attach one EVA Foam on the Curtain housing
adhesive Curtain housing
5.Repeat for the right-hand curtain.
B
A
A.Curtain housing
B. EVA Foam
B
A
4.Check the gap around the unit and seal it with the adhesive
seal attached.
M
check the gap
The M.Sealing sponge is provided only for5K/6K BTU DOE model
Operating your air conditioner properly helps you to obtain the
■ Air conditioner in the Cool mode operation the better limits:
Outdoor side 64.4~109.4°F (18~43 °C), ≤80%RH;
indoor side 62.6~89.6°F (17~32°C), ≤80%RH.
■
Air conditioner in the Heat mode operation the better limits:
Outdoor side 19.4~75.2°F (-7~24 °C), ≤80%RH;
indoor side 32~80.6°F (0~27°C), ≤80%RH.