Hisense AMD-09UX4SJD User manual

Thank you very much for purchasing this Air Conditioner. Please
read this carefully before installing
and using this appliance and keep this manual for future reference.
use and installation instructions

Welcome to use our product!
Thanks for trusting us.
Please read this manual carefully before installation!
Keep it properly for future use after installation!
Features of This Air-Conditioner
The indoor unit is only as thick as 190mm,
which can be installed inside the ceiling
conveniently.
10 and 30 Pa static Pressure was supplied
The standard static pressure outside the
indoor unit is 10 Pa. Then It can also supply
30 Pa.
High Efficiency and Environment Friendly
New Refrigerant-R410A
R410A can protect the environment and do
not harm to the ozone layer.
24-hour Timer ON and OFF
This Timer can be set to automatically turn the
unit on or off at half-hour within a 24-hour
period.
Save Installation Space Mute Operation
The excellent fan design enable the airflow
to be quiet and smooth with minimum noise.
Meeting Various Installation Requirements
The back-air-inlet type is usually be adopted.
According to the actual installation space.
The unit is also installed with down-air-inlet
type and the noise will increase about 5-6 dB.
Self Recovery of Power Break
When the power supply is recovered after
break, all preset are still effective and the air-
conditioner can run according to the original
setting.
Fault Self-diagnose Function
When there is something wrong with the air-
conditioner, the micro computer could
diagnose the faults, which can be read from
the display and is convenient for maintenance.
A - UX4SMD 09 JD
A - UX4SMD 12 JD
A - UX4SMD 18 JD
APPLICATION MODEL

Contents
Alert Symbols
Caution Statements
Composition of the Air-Conditioner
remote controller o Manual
Wire Remote Controller introduce
. Operation with wire remote controller
2.1 Mode function
2.2 sleep function
2.3 Timer function
Remote controller installation
Wireless Remote Controller introduce
4 1
4 2
4 3
. Special Remarks 30
6. Trouble shooting 30
---
----------------------------------------------------------------------2
-----------------------------------------------------------3
1. -------------------------------------------------------- 4
2------------------------------------------------------6
----------------------------------------------------------------6
-----------------------------------------------------------------7
----------------------------------------------------------------7
3.wire ---------------------------------------------------------8
4.------------------------------------------------------9
. . Remote controller-H1 ---------------------------------------------------------------9
4.1.1 -------------------------------------------------------------
4.1.2 -------------------------------------------------------
4.1.3 ----------------------------------------------------------------
4.1.4 ----------------------------------------------------------------
4.1.5 timer mode -----------------------------------------------------------------
4.1.6 sleep mode ----------------------------------------------------------------
4.1.7 super mode ----------------------------------------------------------------
. . Remote controller-J1 --------------------------------------------------------------16
4.2.1 -------------------------------------------------------------
4.2.2 -------------------------------------------------------
4.2.3 ----------------------------------------------------------------
4.2.4 ----------------------------------------------------------------
4.2.5 timer mode -----------------------------------------------------------------
4.2.6 sleep mode ----------------------------------------------------------------
4.2.7 super mode ----------------------------------------------------------------
.. Remote controller-E4-07------------------------------------------------------------23
4.3.1 -------------------------------------------------------------
4.3.2 -------------------------------------------------------
4.3.3 ----------------------------------------------------------------
4.3.4 ----------------------------------------------------------------
4.3.5 timer mode -----------------------------------------------------------------
4.3.6 sleep mode ----------------------------------------------------------------
4.3.7 super mode ----------------------------------------------------------------
---------------------------------------------------------------------
---------------------------------------------------------------------
--- --------------------------------------------------------------------1
peration
operation mode 11
airflow direction control 12
14
operation mode 18
airflow direction control 19
21
operation mode 25
airflow direction controll 26
28
smart mode 13
clock button 13
smart mode 20
clock button 20
smart mode 27
clock button 27
15
15
22
22
29
29
5

: The symbol refers to a hazard which can result in severe personal injury or death.
: The symbol refers to a hazard or an unsafe practice which may result in severe personal injury
or death.
: The symbol refers to a hazard or an unsafe practice which may result in personal injury,
product or property damage.
: It refers to the remarks and instruction to the operation, maintenance, and service.
DANGER
WARNING
CAUTION
NOTE
Alert Symbols：
1
Contents
-----------------------------------------------------------------------
------------------------------------------------
-----------------------------------------------------
-----------------------------------------------------------------
------------------------------------------------------------
-----------------------------------------------------------------
------------------------------------------------------------------
--------------------------------------------------------------
-- -----------------------------------------------------
------------------------------------------------------------------------36
---------------------------------------------------------------------37
--------------------------------------------------------------
-----------------------------------------------------
change of Static pressure ------------------------------------------------------
Installation and Maintenance
1. Safety Notice 31
2. The Tools and Instrument for Installation 32
3. The Installation of the Indoor Unit 32
3.1 Accessories 32
3.2 The Initial Check 32
3.3 Installation 33
4. Refrigerant Pipe 35
4.1 The Pipe Material 35
4.2 The Connection of the Pip 35
5. Drain Piping
6. Electrical wiring
General check
Electrical wiring connection
6.1 37
6.2 37
6.3 38

We recommend that this air-conditioner be installed properly by qualified installation technicians in
accordance with the installation instructions provided with the unit.
Before installation, check if the voltage of the power supply in your home or office is the same as the voltage
shown on the nameplate.
You must not carry on any transformation to this product, otherwise, it may possibly
cause such consequences as the water leakage, the breakdown, the short-circuit, an
electric shock, fire, etc.
The work such as tube line welding, etc. should be carried out far away from the
flammable explosive material vessels, including the air-conditioner refrigerant, to
guarantee the security of the site.
To protect the air-conditioner from heavy corrosion, avoid installing the outdoor unit
where salty seawater can splash directly onto it or in sulphurous air near a spa. Do
not install the air-conditioner where excessively high heat-generating objects are
placed.
Never use gasoline or other inflammable gas near the air-conditioner, which is very
dangerous.
If the supply cord is damaged, it must be replaced by the factory or its service
department in case of danger
The place where this product is installed must have the reliable electrical earth facility
and the equipment. Please do not connect the grounding of this product to various kinds
of air-feeding tube lines, the drain lines, the lightning protection facility as well as other
tube lines to avoid receiving an electric shock and damages caused by other factors.
Wiring must be done by a qualified electrician. All the wiring must comply with the local
electrical codes.
Consider the capacity of the electric current of your electrical kilowatt-hour meter wires
and socket before installation.
The power line where this product is installed is supposed to have the independent
leakage protective device and the electric current over-load protection device which are
provided for this product.
Do not turn the air-conditioner on and off from the power main switch. Use the
ON/OFF operation button.
Do not stick anything into the air inlet and air outlet of both the indoor and
outdoor units. This is dangerous because the fan is rotating at a high speed.
Do not cool or heat the room too much if babies or invalids are present.
CAUTION Statements
2
DANGER
WARNING
Read this manual carefully before using this air-conditioner. If you still have any
difficulties or problems, consult your dealer for help.
The air-conditioner is designed to provide you with comfortable room conditions. Use
this unit only for its intended purpose as described in this instruction manual.
WARNING
CAUTION

3
Composition of the Air-conditioner
Indoor unit
Air inlet
Air outlet
The conditioned air is blown out of the
air-conditioner through it.
Power cord
Drainage
pipe
Refrigerant Pipes
The indoor and outdoor
units are connected by
copper pipes through
which the refrigerant flows.
Outdoor unit
Your air-conditioner may consists of one or two or three or four indoor unit、 an outdoor unit
and its relative accessories.
You can control the air-conditioner with the wire remote controller and wireless remote
controller.
It is used for controlling power ON/OFF,
setting the running mode, temperature,
fan speed and other functions.
Wire remote controller
Wireless remote controller
SET TEMP
ROOM
TEMP
C
AUTO
NO .
ERROR
TIMER ON
TIMER OFF
SET CLOCK
SET TIMER
A
It is used for controlling wire remote controller,
setting the running mode, temperature,
fan speed and air other functions.
Note : The standard duct air-conditioner don’t
consist of wireless remote controller, If you need
you may purchase it
FAN
MODE
TIMER ON
CLOCK
I FEEL
TIMER OFF
SLEEP
SWING
SMART
SUPER
ON
OFF
ON/ OFF
MODE FA N
SLEEP SUPER
SMAR T IFEE L DIMM ER
TIME R ON TIME R OFF CLOC K
ON
OFF
ON
OFF
SWIN G
SWIN G

4
Remote controller operation manual
1.Wire remote controller introuce:
LCD screen
ROOM TEMP
TEMP. setting button
FAN speed/FLAP button
Room temperature sensor
ON/OFF button
MODE select button
TIMER/SLEEP button
Wireless remoter receiver
1 . Room temperature sensor:
A temperature sensor inside the remote control switch is set to sense room temperature, and the temperature
will be sent to indoor unit. When do not connect the remote control switch, indoor unit will switch to the
temperature sensor which is built into indoor unit.
2 . Wireless remoter receiver:
by this receiver, you can use a additional wireless remoter switch to control indoor unit.
3 . ON/OFF button:
press this button to turn on or turn off the unit.
4 . MODE select button:
Press this button to select COOLING, DEHUMIDIFICATION, FAN or HEATING mode.
COOLING mode, the air conditioner makes the room cool.
DEHUMIDIFICATION mode, the air conditioner reduces the humidity in the room.
FAN mode, the air conditioner makes the room's temperature suitable, providing the soft air flow.
HEATING mode, The air conditioner makes the room warm.
5 . TIMER/SLEEP button:
“ ” Press this button to active sleep mode, and will appear in LCD. Press again to cancel sleep function.
Press this button for 3 seconds to active timer function, Press for 3 seconds again to cancel timer function.
To timer function Pls. refer to 2.3
AUTO
C
“ ” “ ”
“ ” “ ”
“ ”
“ ” “ ”
6 . FAN speed button:
Press this button to change current fan speed. You can select (auto fan speed), (low fan
speed), (medium fan speed), and (high fan speed) by each press.
7 . TEMP Setting button:
Press the couple of button to set room temperature you want, when you press SET TEMPERATURE sign
will appear in LCD, press button to reduce setting temperature, and press button to increase
setting temperature.

5
remote controller operation manual
SET TEMP
ROOM
TEMP
C
AUTO
NO .
ERROR
TIMER ON
TIMER OFF
SET TIMER
Display room temperature
and setting temperature
Running state sign area Which
indicate the running state
Fan speed display
8 .LCD screen
Flap direction display (For duct
type unit, this function is invalid)
Mode indication area Which indicate
the current running mode
Display timer setting
Operation mode
cooling mode
dehumidification mode
fan mode
heating mode
auto mode
Fan speed setting
auto fan
high fan speed
meddle fan speed
low fan speed
Temperature display
Room temperature:
Setting temperature:
ROOM
TEMP
C
SET TEMP
C
AUTO
A
TIMER ON
TIMER OFF
timer on
set timer
timer off
Outdoor is defrosting
Compressor is running
Soft running mode is active
Sleep mode is active
A
A

6
remote controller operation manual
2. Operation with wire remote controller
2.1.1 Press MODE button to select operation mode:“ ”
A
cooling mode
dehumidification mode
fan mode
heating mode
auto-run mode(invalid for this model)
2.1.2 Press ON/OFF button to turn on or turn off the unit
2.1.3 Press TEMP. SETTING button to set room temperature. The temperature
range can be set from 18℃ to 32℃。
2.1.4 Press FAN button to set fan speed you want. Of course you can set auto fan and indoor
unit will automatic select fan speed according to the difference between room temperature and
setting temperature
“ ”
“ ”“ ”
“ ”
2.1.5 You may turn off the unit by press ON/OFF button again
Note:
1 .If your air conditioner is multi-type unit, the setting mode may interfere with outdoor mode. This is
because that all indoor units use one outdoor unit, outdoor unit can only run with same mode(cooling
or heating),so, when the mode you set is different from the mode that outdoor is running with, mode
interfere occurs. Following shows the mode interfere scene.
“ ”
cooling dry heating fan
cooling
dry
heating
fan
√× √ √ √ normal
√× √ √ ×mode interfere
× × ×
√
√× √ √
following indoor unit is interfered with it, Three trickle would be heard, The wire remote controll
display 55 error, And the indoor unit interfered with the normal running units would turn off
automatically. It's normal and when you set right mode, the unit may work normally.
2 .For multi-type air-conditioner, the auto mode is invalid.
3 .In fan mode, temperature setting is invalid.
outdoor unit always run with the mode of first indoor unit that turned on. when the setting mode of
2. 1 Mode function

2. 2 sleep function
ROOM TEMP
C
Press timer/sleep button once to active sleep function. And sleep
sign“ ”will appear on LCD.
Press timer/sleep button again to cancel sleep function, and sleep
sign on LCD will disappear.
Note:
During fan mode, the sleep function is invalid.
2.3 Timer function
ROOM TEMP
C
TIMER OFF
2.3.1TIMER OFF mode
1 you can set timer off when indoor unit is running. By press
TIMER/SLEEP button for 3 seconds, timer clock appear on
LCD, and “TIMER OFF”flag will twinkle.,
2 you can adjust the time after which the indoor unit would turn
off automatically by press “ ”“ ” button. The time can
be set from 0.5 to 24(or 12) hour in 30 minutes steps.
3 when you have set the time, press TIMER/SLEEP button for
3 seconds again to active the timer, “TIMER OFF”flag will
stop twinkle, and timer begin to work..
4 IF you need cancel “TIMER OFF”,press TIMER/SLEEP
button for 3 seconds to active the timer, Press “ ”“ ”
button set time 00:00,Cancel “TIMER OFF”after five
seconds automatically.
ROOM TEMP
C
TIMER ON
2.3.2 TIMER ON mode
1 you can set timer on when indoor unit is shut off, By press
TIMER/SLEEP button for 3 seconds, timer clock appear on
LCD, and “TIMER ON” flag will twinkle.,
2 you can adjust the time after which the indoor unit would turn
on automatically by press “ ”“ ” button. The time
can be set from 0.5 to 24(or 12) hour in 30 minutes steps.
3 when you have set the time, press TIMER/SLEEP button
for 3 seconds again to active the timer, “TIMER ON”
flag will stop twinkle, and timer begin to work..
4 IF you need cancel “TIMER ON”, press TIMER/SLEEP
button for 3 seconds to active the timer, Press “ ”“ ”
button set time 00:00,Cancel “TIMER On”after five
seconds automatically.
7
remote controller operation manual