Hisense HK560 User manual

HK560
User’s Manual
Document version 1.0
QingDao Hisense Intelligent Commercial System Co.,Ltd.
1

Safety Notices Before Installation or Use
☆ It is required grounded well and the supply voltage shall be stable, and you must confirm that
the voltage of the outlet provides shall be in line with the voltage marked on the label of the
unit.
☆ Be sure not to sprinkle any liquid or fall any object into the unit.
☆ Be sure not to keep heavy, strenuous movement, shake & heavy strike away from the POS.
☆ Do not switch on or off the host frequently, because it is easy to result in damage on the
machine.
☆ Be sure not to unplug or plug in any live part or external device when they are in energized
state, and the connecting cables of the POS between parts shall be connected securely.
☆ Be sure neither to lengthen cable nor to replace parts at your will, if you have any demand,
please contact with the reseller.
☆ The unit shall be used under dry, ventilated & clean environment away from sunlight. Avoid to
making the air vent of the host machine blocked or covered
☆ If any liquid sprinkles or any sundry falls into the unit, please shut it down immediately & switch
off power supply, take batteries down, dry the liquid or remove the sundry. If you take the
batteries down, you shall reset CMOS.
☆ In case of safety fault, such as peculiar smell, abnormal sound, leakage and other faults, you
must switch off the power supply at once and then contact with reseller.
☆ When inserting USB flash or disk, you shall kill virus to prevent the host machine from virus.
☆ The RJ11 port at the back of the host is connected with the cash drawer, as it is not a
communication port, users shall not use the port for dial-up networking.
☆ The product is a Level A one, it may cause radio interference in living environment. In such case,
users may need to take practical & feasible measures against the interference.
☆ When the POS is not in use, you shall switch off power supply.
The manufacturer has the right to modify the contents of the manual without prior notice!
Product standard NO：Q/0202 RSR527
Product standard Name: POS device
Warning:
1. Absolute Ratings of Environment：
Operating Temperature：0～40℃
Operating Humidity：10%～85%RH
Storage Temperature：-10～50℃
Storage Humidity：10%～90%RH
2. Main plug on the power supply was used as disconnected device. The socket
-outlet shall be installed near the equipment and shall be easily accessible
3. If any damage to the power supply or the equipment, please contact local
service person for help.
4. Static may damage to the integrated circuit in the host machine.
5. If a replaced battery is not right, this may cause explosion or serious
damage. Must replace the same type of batteries or similar ones recommended
by the manufacturer
6. Used only with attached AC/DC power supply.
2

1. Applied range
The HK560 terminal adopt open operating system, flexible component structure and standard peripherals. The
products are suitable for the commercial enterprises, such as restaurants, supermarkets, and convenience stores to
Internet –connected use or stand-alone use. The main components are standard parts, so the quality of the
products is reliable, the system is easy to upgrade and the components are conveniently and easily maintained.
Reasonable price ratio makes it more competitive than similar products.
Specification ：
Item Description
Model HK560
System
CPU Intel Celeron J1900, Quad core CPU, clock speed 2.0GHz
Memory DDR3L 1333Mhz ,2G, up to 8GB
Storage Flash Memory 3D NAND SSD,64GB up to 256GB
LCD Touch Panel
LCD Size 15.6 inch
Resolution 1920×1080
Touch Screen capacitive true flat touch
I/O Ports
Serial Ports 3* RJ48 COM(COM1-3); COM2 COM3 voltage is adjustable
USB 4* USB 2.0(3* on IO panel, 1*under side cover )
1*USB3.0 (on IO panel)
Powered USB 1* USB 2.0 ,24V, on IO panel
LAN 1 * RJ-45 (100M/1000Mbps Gigabit LAN)
Audio 1 * Line-out
Cash Drawer 1 * RJ-11 for cash drawer
Power Power Adapter Adapter (DC 24V, 2.5A)(Standard)
Adapter(DC 24V, 5A)(optional)
Peripheral
VFD 2*20 characters
Second Display 15.6 inch (touch/non-touch)
10.1inch(touch/non-touch)
Printer Separate 80MM thermal printer
MSR card reader 3 Tracks
RFID card reader RFID (Supports MIFARE one and MIFARE CPU card)
Operating system Windows7/posready7/windows8.1/windows10/linux
3

2. I/O port view
1、24V Power in 2、cash drawer(24V)
3、Powered USB(24V) 4、USB*2
5、USB*2 6、COM1
7、COM2 8、COM3
9、LAN 10、audio
3. Mainboard
Mainboard front layout:
4

Jumpers / Headers and Connectors
1
SYS_FAN1
System Fan Connector
2
CLR_CMOS1
CMOS Clear Jumpe
3
J_VGA1
VGA Pin Heade
4
J_COM4, J_COM5, J_COM6
COM4-6 Pin Headers
5
F_USB1
Front USB2.0 Pin Header1
6
J_PWRCOM4
COM4 VCC Select Jumpe
7
F_USB2
Front USB2.0 Pin Header2
8
F_USB3
Front USB2.0 Pin Header3
9
F_USB4
Front USB2.0 Pin Header4
10
F_PANEL1
Front Panel FPC Connector
11
J_RST1
System Reset Button Pin Header
12
J_MIC1
MIC Pin Header
13
J_SPK1
Amplifier Pin Header
14
R_USB4
USB2.0 TYPE-A Connector
15
S_ATA1
SATA2.0 Port (7+15P)
16
EDP1
EDP1 Signal Connector
17
EDP2
EDP2 Signal Connector
18
MINI_PCIE1
Mini PCI-E1 Slot
19
DIMM1
SO-DIMM DDR3L Slot
20
NGFF1
M.2 (NGFF) Key-B Slot (SSD, 2280)
21
DC_IN1
DC24V Power Input Connector (4Pin Jack)
22
RJ11_1
Cash Draw RJ11 Connector
5

23
R_USB1(R_USB5)
POWER USB 24V Key-2 Connector (USB2.0
TYPE-A Connector)
24
R_USB2
USB2.0 Dual TYPE-A Connector
25
R_USB3
USB3.0+USB2.0 TYPE-A Connector
26
COM1
COM1 RJ50 Connector
27
COM2
COM1 RJ50 Connector
28
COM3
COM1 RJ50 Connector
29
RJ45_1
LAN RJ45 Connector
30
PJ1
Line-out 3.5mm Jack
EDP1 (EDP1 Signal Connector 40*1 Pin 0.50mm)
EDP2 (EDP2 Signal Connector 40*1 Pin 0.50mm)
6

J_VGA1 (VGA Pin Header 12*2 Pin 2.00mm)
7

J_PWRCOM4 (COM4 VCC Select Jumper 3*2 Pin 2.54mm)
CLR_CMOS1 (CMOS Clear Jumper 3*1 Pin 2.54mm)
8

4. Device Assembly and disassembly
1). Unscrew the two screw shown to remove the back shell of the base.
2).After removing the screw, pull at the back shell of the base according to the picture shows, and remove the back
shell of the base.
3).Remove the two connectors shown in the picture and protect them with the tape according to the picture shows
(to prevent the connector from being pulled out in the process of dismantling and threading);
9

4).Rotate the main screen and the secondary screen : to the vertical angle, remove the three screws of the main
screen hinge and the second screen hinge respectively, and carefully pass the screen line through the line hole.
Separate the main and auxiliary screen from the base respectively.
5).Remove the hinges of the host: Remove four screws according to the picture shows. Remove the hinges of the
host and the hinges cover of the host separately.
6).Remove the extended interface cover: pull the expanded interface cover outward at the notch according to the
picture shows, and remove it.
10

7. remove the hard drive, unscrew the hard drive fixing screw, then remove the hard drive as arrow
direction show in the picture below.
8.remove the host back cover, remove the screws of hinge cover(4 pcs, show as ①) and screws of
back cover(4 pcs, show as ②), then remove the back cover ,and then you may replace or
maintenance the mainboard.
5. Environmental requirements
Type
State
11

Environmental
Voltage
AC 100V-240V 50-60Hz Bipolar
Temperature 5
℃
- 40
℃
Optimal
40% - 90%
6. Size specification
Single screen，Length×Width×Height：405*210*330；Flip Angle 0-45°
Double Screen，Length×Width×Height：405*250*370；
Main Flip Angle 0-45°，Second screen Flip Angle 0-30°
High position +printer，Length×Width×Height：405*250*420
12

Self-service，Length×Width×Height：230*250*450
7. Open the box and check.
1) Before opening the box, check whether the box is in good condition, and whether there is any obvious
damage.
2) The equipment must be installed by technical service person or distributors.
Operation
1) Switching Instructions：
Start-up: When the adapter is connected, hold down the switch button on the right back side of the
bottom of the machine for about 3 seconds. When the screen is on and the button indicator light is on, the
startup can be realized.
Shutdown: Press the switch button on the right back side of the bottom of the machine for about 3
seconds, and operate according to the screen prompt, which can realize shutdown and restart functions.
3) Swipe magnetic cards：
When swiping the card, the machine should be placed on a hard horizontal plane.
Please swipe the magnetic strip of the magnetic strip card inward from the swipe slot.
The process of card swiping should be smooth and uniform.
13

4) Contactless card operation：
Contactless card induction zone is located behind the right side of the host (with the contactless mark
printed).
When need read contactless card, please place the card above the induction zone.
8. Printer operations
1) Printer Structure
14

2) Load and change paper introduction
a. Press the open button to open the paper bin cover, as shown below. If there are paper tubes in the paper
warehouse, please take them out.
b. Put the paper roll into the paper bin, pay attention to the correct direction of the paper roll.
c. Please take out a small amount of paper from the front of the roll and close the cover of the printer's
paper bin
15

d. Remove excess paper toward the side of the paper cut.
Paper rolling
1) Requirements of the thermal paper：
Type：Thermal paper
Width of paper：57.5±0.5mm / 79.5±0.5mm
Outside Diameter of paper roll：Max 83mm
Thickness of Thermal Paper：0.056 ~ 0.13mm
2) Recommendation of thermal Paper Model：
Type
Manufacture
FD210,PD150R,PD160R
OJI Paper CO.,
Notes：
16

A. Please use the recommended paper roll or the same quality paper roll. The use of other types of paper roll
may affect the printing effect and the life of the printing head.
B. If the paper roll is contaminated by chemicals or oil, the contaminated part of the paper roll may fade or the
printing effect is not clear.
C. Do not scratch the thermal sensitive layer of the paper roll with sharp objects, which may make the printing
effect unclear.
D. When the temperature exceeds 70 degree C, the thermal sensitive layer of the paper roll will fade. Therefore,
the use or storage of paper rolls should avoid high temperature, high humidity, strong light, etc.
E. Thermal paper that has been stored for too long should not be used.
Printer Maintenance
(1) Printer head and Printer rubber roller
When one of the following situations occurs in the printing unit, the print head should be cleaned:
A. Printing is not clear;
B. The vertical column of the printed page is not clear.
C. Noise of feeding and returning paper is high.
The cleaning steps of the printing head and Printer rubber roller are as follows:
A. Turn off the power supply of the printing unit, open the printer cover, and expose the printer head and Printer
rubber roller;
B. If you have just finished printing, you should wait for the print head to cool completely.
C. Use alcohol cotton balls (should be screwed dry) to erase the dust, stains and paper scraps on the surface of the
printed hair heater.
D. Close the top cover of the printer after the alcohol evaporates completely.
(2) Daily maintenance matters needing attention
A. The power supply must be turned off during the daily maintenance of the printing unit.
B. Do not touch the surface of the printing head with your hands or metal objects. Do not scratch the surface of the
printing head, Printer rubber roller and sensors with tweezers or other tools.
C. Organic solvents such as gasoline and acetone should not be used.
D. Wait for the cleaning solution to evaporate completely, then turn on the power supply to continue printing.
E. Maintenance cycle: It is recommended to clean it up once a month.
9. accessories
No. Item Unit Quantity
Note
1 POS terminal 1
2 Power adaptor 1
3 Power cable 1
17

FCC Statement：
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference,and (2) this device must accept
any interference received, including interference that may cause undesired operation.
18
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.