Hitachi UX Twin Nozzle User manual

Instruction Manual for LAN Communication Modbus
Ethernet Communication
HITACHI Printer
Model UX Twin-Nozzle
Thank you for purchasing the Hitachi IJ Printer Model UX Twin Nozzle.
This instruction manual describes the Ethernet communication (LAN Communication Modbus)
function. For other features of the printer, please refer to Instruction manual or Technical
manual.
If the printer is improperly handled or maintained, it may not operate smoothly and may become
defective or cause an accident. It is therefore essential that you read this manual to gain a
complete understanding of the printer and use it correctly.
After thoroughly reading the manual, properly store it for future reference.
First Edition

Table of Contents
1. Ethernet communication (LAN communication Modbus) function························· 1
2. Preparations ·································································································· 2
2.1 Network connection preparations ·································································· 2
2.2 IJ Printer preparations ·················································································· 2
2.3 LAN cable connection ·················································································· 3
2.4 Setting the communication environment ························································ 4
2.4 Usage precautions ······················································································· 4
3. Connection test ····························································································· 6
3.1 Procedure for connection test ······································································· 6
4. Modbus communication ················································································· 9
4.1 Overview ····································································································· 9
4.2 Transmission procedure ··············································································· 9
4.3 Message format ··························································································· 9
4.4 Data configuration ·······················································································15
4.5 Detail of Data configuration ··········································································37
4.6 Modbus communication rule for IJ Printer ·····················································39
4.7 Examples of Transmission procedure ···························································40
5. Troubleshooting guide ···················································································45
"Ethernet" is a registered trademark of Xerox Corporation, USA.
"Windows" is registered trademarks of Microsoft Corporation, USA, in the USAand other countries.

1
1. Ethernet communication (LAN communication Modbus) function
(1) Overview
●Function for Ethernet communication between the IJ Printer and external unit employing a
LAN environment.
●Type of Ethernet communication can be selected from Modbus communication.
●Modbus communication require development of a communication program on the external
unit side.
For the development purpose of communication program, IJP control library will be provided
as a development kit.
List of functions
No. Function name Description
1 Modbus
communication
Supports Modbus protocol. Because Modbus protocol is one type of
protocol commonly used by industrial equipment, if Modbus
communication is employed for other unit, you can create a
communications program for the external unit using this asset.
When the communication program is newly developed, its
development schedule will be shortened with use of IJP control
library.
(2) Configuration diagram
Standard specifications
Item Specifications
Ethernet standards IEEE802.3 compatible, 10BASE-T, 100BASE-T
Protocol TCP/IP
Connection cable Category 5 UTP or STP cable
(3) Notice
●The time from when the signal is transmitted from an external unit to when the IJ Printer
receives the signal cannot be strictly defined in the same way as with serial communications.
Ethernet
External unit
IJ Printer

2
2. Preparations
●If connecting the IJ Printer with external unit, use a LAN connection cable.
2.1 Network connection preparations
(1) Connect to Intranet LAN
No. Work Remarks
1 You should obtain the IP address from the Information
Systems Department of your company.
2 You should consult with the Information Systems Department
of your company concerning network settings such as
gateway.
(2) Connect from outside the company
No. Work Remarks
1 After concluding a contract with a provider, you should obtain
a fixed IP address from the provider.
2 If using a telephone line, a contract for service such as ADSL
is required. If not using a telephone line, a mobile
environment is required. You also need a router that supports
a mobile card.
3 Set the network settings as instructed by the provider's
manual.
2.2 IJ Printer preparations
No. Work Remarks
1 Connect the IJ Printer to the Ethernet (computer or
hub, etc.) with a LAN cable.
Refer to 2.3 LAN cable
connection.
2 Set the communication environment on the IJ
Printer's screen.
Refer to
2.4 Setting the communication
environment.
3 Conduct a connection test if necessary. Refer to
3.Connection test.

3
2.3 LAN cable connection
[I/O section (with cover removed)]
Connect the LAN cable.

4
2.4 Setting the communication environment
●Set the LAN function on communication environment setup screen to "Modbus
communication".
Setting item of communication environment setup screen
Setting item Description
LAN function
●No use: Modbus communication function cannot be used.
●Modbus Communication: Modbus communication function
canbeused.
IP address Sets IJ Printer’s IP address.
Subnet mask Sets IJ Printer’s Subnet mask.
Default gateway Sets IJ Printer’s Default gateway.
PORT No. Sets IJ Printer’s PORT No.
MAC address Displays IJ Printer’s MAC address.
Example communication environment setup screen
2.5 Usage precautions
(1) Functions listed below are not operational during the use of this function.
List of functions which are not operational during the use of this function
(2) Functions listed below are not supported by this function.
List of functions which are not supported by this function
No Screen Item Note
1 Comm. env. setup Buffer function [Disable] Fixed
2 Data exchange [Reflect at once] Fixed
No Function
1 More than one of Calendar/Count blocks can not be set in one item.
2 Barcode can not be set in Calendar/Count block.
3 “Overall setup” of “Format setup” can Not be used.
4 Kanji characters can not be used.

5
Glossary
Term Explanation
IP address
(Internet protocol address)
The IP address is a 32-bit ID number allotted to equipment
connected to the Internet. The 32-bit number of the IP address is
usually divided into four 8-bit segments for display. The IP
address consists of a "network address" that identifies the
network and a "host address" that identifies the individual pieces
of equipment connected in the network.
Subnet mask The subnet mask is a 32-bit number that defines what bits of the
IP address are used for the network address. The network
address segment of the IP address is determined by calculating
the logical AND of the IP address and subnet mask.
Default gateway The default gateway is equipment such as a router that functions
as the "gateway" to the network. When there is communication
between different networks and there is no unique path for the
equipment to be accessed, the default gateway is used to
connect them.
Port number The port No. is the sub-address that specifies one of several
programs running on equipment specified by the IP address.
Port numbers 502 or 1024-65535 are used as the sub-address.
MAC address
(Media Access Control
address)
MAC address is the one to identify the device on a network.
MAC address consists of 12 digits such as 01-23-45-67-89-AB.

6
3. Connection test
Directly connect the IJ Printer to a PC and check the connection.
3.1 Procedure for connection test
1 Directly connect the IJ Printer to the PC with a LAN cable.
2 Set the network settings of external unit by steps 2 to 5.
Click the Start menu, and double-click [Control Panel] > [View network status and tasks] > [Change
adapter settings] > [Local Area Connection].
The following window is then displayed.
3 Click [Properties].
(Example using Windows 7 OS)

7
4 Click [Internet Protocol Version 4 (TCP/IPv4)].
5 Select [Use the following IP address], and enter an IP address other than 192.168.0.1 and
192.168.0.255 (the example shown in the figure uses 192.168.0.15) and then enter 255.255.255.0
in the Subnet mask field. Click [OK].

8
6 Follow the steps below to confirm that the network connection is properly established. The following
steps describe procedures for Windows 7.
Select [Start Menu] > [All
Programs] > [Accessories] >
[Command prompt] to open the
Command Prompt window.
Type the following command:
Ping 192.168.0.1
Note:
This command is not case
sensitive.
Byte=32 time=24ms ..in four
consecutive lines*1 then external
unit settings are completed.
*1:
In default, the ping command
returns the response for four
times. For details of the ping
command, type the following
command: ping/help
If "Destination host unreachable."
response is returned for the ping
command, it means
communication has not been
established between the IJ Printer
and external unit. Re-check the
following:
[Check points]
* Have the communication
settings of the IJ Printer
been changed?
* Are the network settings of
the external unit correct?

9
4. Modbus communication
4.1 Overview
●Function that supports Modbus protocol. Modbus protocol specifications have been globally
disclosed; Modbus protocol is one of the most common types of communication protocol.
●Modbus protocol does not support messages autonomously output by the IJ Printer such as
status or printing contents.
4.2 Transmission procedure
No. Name Size
Setting
range Description
1 Transaction
identifier
2 bytes 0x0000 to
0xFFFF
The IJ Printer returns the transaction
identifier received from external unit as it is.
You should use the identifier to manage
messages for external unit.
2 Protocol identifier 2 bytes 0x0000 Sets protocol identifier. Set protocol identifier
to 0x0000. The IJ Printer returns the protocol
identifier received from external unit as it is.
3 Data length
2 bytes 0x0000 to
0x00FF
Sets number of bytes for request data and
response data.
4 Data 3 to 255
bytes
- Because message format differs according
to the function code specified, data size is
variable refer to 4.3 Message format for
details.
4.3 Message format
(1) Function code
The IJ Printer supports the function code given in the following table.
Function code
No. Function
code Function
1 0x10 Write Multiple Registers
2 0x06 Write Single Register
3 0x03 Read Holding Registers
4 0x04 Read Input Registers
Transaction
identifier
External unit
IJ Printer
Protocol
identifier Data length Data
Transaction
identifier
Protocol
identifier Data length Data
Request message
configuration
Response message
configuration

10
(2) Device address
Addresses are color-coded as shown in 4.4 Data configuration.
IJ Printer operates as described below with the device address which is specified.
Operation when a data is written
№Color of address Device address Description
1 0x01 Write into device.
0x02 Write into device.
0x03 Write into device.
2 0x01 Write into Nozzle 1.
0x02 Write into Nozzle 2.
0x03 Error response.
3 0x01 Write into Nozzle 1.
0x02 Write into Nozzle 2.
0x03 Write into both Nozzle 1 and Nozzle 2.
Operation when a data is read
№Color of address Device address Description
1 0x01 Read from device.
0x02 Read from device.
0x03 Read from device.
2 0x01 Read from Nozzle 1.
0x02 Read from Nozzle 2.
0x03 Error response.
3 0x01 Read from Nozzle 1.
0x02 Read from Nozzle 2.
0x03 Read from Nozzle 1.
: Unique data of IJ Printer as a device.
: Data existing for each Nozzle of IJ Printer.

11
(3) Message format for Write Multiple Registers (Function code: 0x10)
●Writes contents in the Holding Register to reflect it in the IJ Printer.
●The maximum number of bytes that can be written in the Holding Register per time is 246
bytes; if this number is exceeded, you must divide the data into smaller segments while
updating the starting address each time.
●When the writing operation onto Holding Registers is made more than once, 0x0001 (Start)
shall be written first on the control flag which is placed in the first address 0x0000 of Holding
Registers. Then conduct writing more than once and finally write 0x0002 (Stop) onto the
control flag. When 0x0002 (Stop) is written on the control flag, the data being written on
Holding Registers will be reflected to IJ printer.
Request message configuration
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address.
2 Function code 1 byte 0x10 Sets function code (Write Multiple
Registers).
3 Start address 2 bytes 0x0000 to
0xFFFF
Sets writing start address. Address is
set in word units.
4 No. of words to be
written 2 bytes 1 to 123 Sets number of words to be written.
5 No. of bytes to be
written 1 byte 1 to 246 Sets number of bytes to be written.
6 Data to be written 2 to 246
bytes
0x0000 to
0xFFFF
Sets data to be written (variable
length of 2 to 246 bytes). 0x00 is
added to the end when data of
uneven byte length is set.
Response message data configuration (normal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x10 Sets function code received as it is.
3 Start address 2 bytes 0x0000 to
0xFFFF Sets start address received as it is.
4 No. of words to be
written 2 bytes 1 to 123 Sets No. of words to be written
received as it is.
Response message data configuration (abnormal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x90 Adds 0x80 to function code received.
3 Error code 1 byte 0x01 to 0x03 Sets error code. Error code differs
according to cause.

12
(4) Message format for Write Single Register (Function code: 0x06)
●Write a content in the Holding Register to reflect it in the IJ Printer.
●The number of bytes that can be written in the Holding Register per time is fixed to 2 bytes.
Request message configuration
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address.
2 Function code 1 byte 0x06 Sets function code (Write Single
Register).
3 Writing address 2 bytes 0x0000 to
0xFFFF
Sets writing address. Address is set
in word units.
4 Data to be written 2 bytes 0x0000 to
0xFFFF Sets data to be written.
Response message data configuration (normal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x06 Sets function code received as it is.
3 Writing address 2 bytes 0x0000 to
0xFFFF Sets writing address received as it is.
4 Data to be written 2 bytes 0x0000 to
0xFFFF
Sets data to be written received as it
is.
Response message data configuration (abnormal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x86 Adds 0x80 to function code received.
3 Error code 1 byte 0x01 to 0x03 Sets error code. Error code differs
according to cause.

13
(5) Message format for Read Holding Registers (Function code: 0x03)
●This function will be used to read the item data of IJ printer, which is readable and writable.
●The maximum number of bytes that can be read in the Holding Register per time is 250 bytes;
if this number is exceeded, you must divide the data into smaller segments while updating the
starting address each time.
Request message configuration
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address.
2 Function code 1 byte 0x03 Sets function code (Read Holding
Registers).
3 Start address 2 bytes 0x0000 to
0xFFFF
Sets reading start address. Address
is set in word units.
4 No. of words to be read 2 bytes 1 to 125. Sets number of words to be read.
Response message data configuration (normal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x03 Sets function code received as it is.
3 No. of bytes to be read 1 byte 2 to 250 Sets number of data bytes to be read.
4 Data to be read 2 to 250
bytes
0x0000 to
0xFFFF
Sets data to be read (variable length
of 2 to 250 bytes).
Response message data configuration (abnormal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x83 Adds 0x80 to function code received.
3 Error code 1 byte 0x01 to 0x03 Sets error code. Error code differs
according to cause.

14
(6) Message format for Read Input Registers (Function code: 0x04)
●This function will be used to read the item data of IJ printer, which is read only, or used to read
the status of IJ printer.
●The maximum number of bytes that can be read in the Input Register per time is 250 bytes; if
this number is exceeded, you must divide the data into smaller segments while updating the
starting address each time.
Request message configuration
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address.
2 Function code 1 byte 0x04 Sets function code (Read Input
Registers).
3 Start address 2 bytes 0x0000 to
0xFFFF
Sets reading start address. Address
is set in word units.
4 No. of words to be read 2 bytes 1 to 125 Sets number of words to be read.
Response message data configuration (normal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x04 Sets function code received as it is.
3 No. of bytes to be read 1 byte 2 to 250 Sets number of data bytes to be read.
4 Data to be read 2 to 250
bytes
0x0000 to
0xFFFF
Sets data to be read (variable length
of 2 to 250 bytes).
Response message data configuration (abnormal)
No. Name Size Range Description
1 Device address 1 byte 0x01 to 0x03 Sets device address received as it is.
2 Function code 1 byte 0x84 Adds 0x80 to function code received.
3 Error code 1 byte 0x01 to 0x03 Sets error code. Error code differs
according to cause.
(7) Error code Error code
No. Name Code Conditions
1 Illegal function code 0x01 Function code not yet supported is set.
2 Illegal address 0x02 Illegal address is set.
3 Illegal data 0x03 Illegal data is set.

15
4.4 Data configuration
Data configuration of Holding Registers and Input Registers for IJ Printer is indicated.
(1) Holding Registers
Holding Registers are the area which is written by Write Multiple Registers (0x10) or Write
Single Register (0x06) and read by Read Holding Registers (0x03).
The item data which can be set to IJ printer or can be obtained from IJ printer are all placed in
Holding Registers.
Holding Registers can be read and be written by one (1) word (2 bytes) fixed at every address.
Holding Register data configuration (1/13)
Word
address Classification Item name Setting range Contents
00 00
Index
Start/Stop control flag 1 , 2
Start/Stop flag is used when
Holding Register is written more
than once. First write “1” and write
Holding Registers more than once
and finally write “2”. Then all the
written contents will be reflected to
IJ Printer. Start/Stop flag is not
used when Holding Register is
written only once. [1:Start; 2:Stop]
00 01 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
00 07 Reserve_7
00 08 Number of the printing items 1 to 50 Set the number of the printing
items used.
00 09 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
00 0F Reserve_7
00 10 Specify Print message
registration number 0 to 2000
Set Print message information at
Input Register address 0x0E40,
which Print message registration
number is specified here. When “0”
is specified, the print message
information of the print message
which is being edited will be set.
00 11
Specify Character position for
the Inter-character space
obtained
1 to 500
Set Inter-character space at Input
Register address 0x0EF1, which
Character position is specified
here.
00 12 Specify Substitution rules
number 1 to 99
Set Substitution rules data at
Holding Register address 0x1AC0,
which Substitution rules number is
specified here.
00 13 Specify User pattern character
size 1 to 13
Set User pattern registration
information at Holding Register
address 0x2D00, which
Character size is specified here.
1:4x5, 2:5x5, 3:5x8(5x7), 4:9x8(9x7),
5:7x10, 6:10x12, 7:12x16, 8:18x24,
9:24x32, 10:11x11, 11:5x3(chimney),
12:5x5(chimney), 13:7x5(chimney),
00 14 Specify Group number 1 to 99
Set Group information at Input
Register address 0x0ED0, which
Group number is specified here.
00 15 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
00 1F Reserve_11

16
Holding Register data configuration (2/13)
Word
address Classification Item name Setting range Contents
00 20
Print
contents
Character count(Print item 1) 1 to 500
Sets the character count for each
print item.
00 21 Character count(Print item 2) 1 to 500
… … …
00 50 Character count(Print item 49) 1 to 500
00 51 Character count(Print item 50) 1 to 500
00 52 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
00 83 Reserve_50
00 84 Attribute(1st digit) 0x0000 to 0xFFFF Set the characters of Print
contents. Character codes are the
same as those which are used in
Standard communication. Please
refer to Technical Manual, Section
5 Communication, for details.
In case of setting Calendar/Count
characters, set to Character
attribute, or if they are NOT
Calendar/Count characters, set to
Character code.
00 85 Character code(1st digit) 0x0020 to 0xFFFF
… … …
04 6A Attribute(500th digit) 0x0000 to 0xFFFF
04 6B Character code(500th digit) 0x0020 to 0xFFFF
04 6C Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
0F FF Reserve_2964
10 00
Printings
erasure
Printing erase item number 1 to 50 Sets the printing item number to
erase printing contents.
10 01 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
10 05 Reserve_5
10 06
Print data
recall
Print data message number 1 to 2000 Set the registered print message
number to be recalled.
10 07 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
10 0B Reserve_5
10 0C
Print data
registration
Group number 0 to 99
Register the being edited print
message by the specified Group
number or by the registered print
message number or by the
message name.
10 0D Print data message number 1 to 2000
10 0E Message name(1st digit) 0x0020 to 0xFFFF
10 0F Message name(2nd digit) 0x0020 to 0xFFFF
… … …
10 18 Message name(11th digit) 0x0020 to 0xFFFF
10 19 Message name(12th digit) 0x0020 to 0xFFFF
10 1A Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
10 1F Reserve_6
10 20
Print format
Line count / print format
uniformity 0 , 1 Line count of all columns are made
uniform based on the first column.
10 21 Insert column 1 to 50 Adds a column directly before the
editing objective column.
10 22 Delete column 1 to 50 Deletes all the print items of the
editing objective column.
10 23 Add column 1 to 50 Adds a column at the end.
10 24 Individual column setup
(Column position) 1 to 50 Changing the number of lines of
the editing objective column.
10 25 Individual column setup
(Line count) 1 to 4
10 26 Reserve_1 - "Reserve" is not initially provided,
but may be added in future.
10 27 Reserve_2

17
Holding Register data configuration (3/13)
Word
address Classification Item name Setting range Contents
10 28
Print format
Adjust Inter-character space
(Start) 1 to 500
Inter-character space can be set in
character units.
10 29 Adjust Inter-character space
(End) 1 to 500
10 2A Adjust Inter-character space
(Setting value) 0 to 28
10 2B Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
10 3E Reserve_20
10 3F Format Setup 1 to 3
Sets the Format Setup.
1:Individual setup , 2:Overall setup
3:Free layout
10 40 Line count 1 to 4 Sets the line count of the print item
1.
10 41 Line spacing 0 to 2 Sets the line spacing of the print
item 1.
10 42 Character size 1 to 13
Sets the character size of the print
item 1.
1:4x5 , 2:5x5 , 3:5x8(5x7)
4:9x8(9x7) , 5:7x10 , 6:10x12
7:12x16 , 8:18x24 , 9:24x32
10:11x11 , 11:5x3(chimney)
12:5x5(chimney), 13:7x5(chimney)
10 43 Inter-character space 0 to 28 Sets the inter-character space of
the print item 1.
10 44 Bold 1 to 9 Sets the bold of the print item 1.
10 45 Bar code 0 to 26
Sets the bar code of the print item
1.
0:none , 1:Code 39 , 2:ITF
3:NW-7 , 4:EAN-13 , 5:DM8x32
6:DM16x16 , 7:DM16x36
8:DM16x48 , 9:DM18x18
10:DM20x20 , 11:DM22x22
12:DM24x24
13:Code 128 (Code set B)
14:Code 128 (Code set C)
15:UPC-A , 16:UPC-E , 17:EAN-8
18:QR21x21 , 19:QR25x25
20:QR29x29 , 22:EAN-13add-on 5
23:MicroQR15x15
24:GS1 DataBar (Limited)
25:GS1 DataBar (Omnidirectional)
26:GS1 DataBar (Stacked)
10 46 EAN readable code 0 to 2
Sets the EAN readable code of the
print item 1.
0:none , 1:5x5 , 2:5x7
10 47 EAN Prefix 0 to 99 Sets the EAN prefix of the print
item 1.
10 48 Calendar block No. 0 to 8 When writing, setting is NOT
required. When reading, Block
information can be obtained item
by item.
10 49 Calendar block count 0 to 8
10 4A Count block No. 0 to 8
10 4B Count block count 0 to 8
10 4C Horizontal (X) 0 to 31998 Valid when Free layout is set.
Sets the coordinate of the print
item 1.
10 4D Vertical (Y) 0 to 29
10 4E Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
10 57 Reserve_10

18
Holding Register data configuration (4/13)
Word
address Classification Item name Setting range Contents
10 58
Print format
Print format(Print item 2)
-
Item 2 through 50 will be set in the
same configuration as those of
Item 1 (Address: from 0x1040 to
0x1057).
10 6F
… …
14 D8 Print format(Print item 50)
14 EF
14 F0 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
19 9F Reserve_1200
19 A0
Print
specification
Character height 0 to 99 Sets the character height.
19 A1 Ink drop use 1 to 16 Sets the ink drop use.
19 A2 High-speed print 0 to 3 Sets the high-speed print.
0:HM , 1:NM , 2:QM , 3:SM
19 A3 Character width 0 to 3999 Sets the character width.
19 A4 Character orientation 0 to 3 Sets the character orientation.
19 A5 Print start delay 0 to 9999 Sets the print start delay.
19 A6 Reverse direction 0 to 9999 Sets the reverse direction.
19 A7 Product speed matching 0 to 3
Sets the product speed matching.
0:None , 1:Encoder , 2:Auto
3:Encoder(enhance)
19 A8 Pulse rate division factor 1 to 999 Sets the pulse rate division factor.
19 A9 Speed compensation 0 , 1 Sets the speed compensation.
0:Disable , 1:Enable
19 AA Line speed 0 to 9999
Sets the line speed.
Set value is multiplied by 1/10 and
reflected to IJ Printer. .
(Example : 1234 = 123.4 m/min.)
19 AB Distance between print head
and work 0 to 99 Sets the distance between print
head and work.
19 AC Print Target width 0 to 9999 Sets the print Target width.
19 AD Actual Print width 0 to 9999 Sets the actual Print width.
19 AE Repeat count 0 to 9999 Sets the repeat count.
19 AF Repeat intervals 0 to 99999 Sets the repeat intervals.
19 B0
19 B1 Target sensor timer 0 to 999 Sets the target sensor timer.
19 B2 Target sensor filter 0 , 1 Sets the target sensor filter.
0:Time setup , 1:Until end of print.
19 B3 Target sensor filter value 0 to 9999 Sets the target sensor filter value.
19 B4 Ink Drop Charge Rule 0 to 2
Sets the ink drop charge rule.
0:Standard
1:Mixed single scan and interlaced
2:Dot mixed interlaced
19 B5 Speed compensation fine
control -50 to 50 Sets the speed compensation fine control.
19 B6 Reserve_1
- "Reserve" is not initially provided,
but may be added in future.
… …
19 BF Reserve_10