HiTi Digital 640Amphi User manual

Quick Start
Contents in Carton
Setting Your Printer
Installing Ribbon Cartridge
Installing Card/ Photo paper
System Requirements
Installing Driver
Customer Service
Contact Information
About PhotoDesiree
Installing Software
User Interface
Printing Photo

 Quick Start
Contents in Carton
Before you begin to install printer, please check you have the following
items.
 HiTi Photo/ Card Printer 640Amphi x 1
 Plastic Card Cassette x 1
 Photo Paper Cassette x 1
 Power Cord x 1
 USB Cable x 1
 CD (Windows Driver, PhotoDesiree, CardDesiree) x 1
 Printer/ Software User Manual x 2
 Trial Clean Kit (2 sheets clean paper) x 1
 Warranty Card x 1
640Amphi Plastic Card Cassette
Photo Paper Cassette
Power CordUSB Cable
CD
Printer/Software
User Manual
X 2
X 2

 Quick Start
Setting Your Printer
You may setup HiTi 640Amphi printer in the following steps.
1. Connect the power cord to the printer.
2. Connect the printer to your computer using the
USB cable.
3. Insert the ribbon cartridge into the printer; please see P.XX for more
information.
4. Place photo paper or plastic card into the cassette; please see P.XX
for more information.
5. Turn the printer power switch on. The green LED will blink for 5
seconds and then stay on. Before you turn on the power switch,
please make sure the printer driver software is installed in your
personal computer. Please see P.XX for more information about
driver installation.
6. The New Hardware Found message dialog will appear on the screen
of your computer. Windows will begin to install the printer driver.

Notice!!
Please always turn the power switch off before connecting or
disconnecting the printer from the power source.

 Quick Start
Installing Ribbon Cartridge
You may install the ribbon cartridge in the following steps.
1. Push the slider to open the top cover of the
printer.
2. Hold the ribbon cartridge as the figure illustrated.
Be sure to point the arrow sign towards the
left-hand side of the printer.
3. Insert the cartridge all the way into the printer
until it is properly seated.
4. Close the top cover.

Notice!!
1. Please check the LED indicator should be green after door closed, if
LED indicator is orange, try to close the ribbon door again.

 Quick Start
Installing Paper/Card
You may install the photo paper or the plastic card in the followings
steps.
1. Open the cover of the
paper cassette.
2. Remove the clean roller of
the plastic card cassette.
3. When you place a stack of
plastic card into the plastic
card cassette, please make
sure the notch is close to
right side, please refer to illustration.
When you place a stack of photo paper into the photo paper
cassette, please make sure the wider blank part of photo paper is
close to cassette-open side, please see instruction on paper
package for more information.
4. Insert the plastic card cassette into the printer.

Notice !!
1. Maximum photo paper capacity of 640Amphi is 100 sheets. Maximum
plastic card capacity is 50 sheets or 25 sheets
for the adhesive plastic card.
2. When doing double-sided card printing, please
align the card notch to the right side of the
cassette when printing the front side of the card. When printing the
back side of the card, please align the plastic card to the left side of
the cassette.

 Quick Start
System Requirement
Please make sure your PC conforms to the following requirements.
 Intel Pentium or compatible PC
 Windows 98/ME/2000/XP
 128MB RAM or greater
 Available USB port
 100MB or greater free hard disk space
 CD-ROM Drive
Notice!!
1. Microsoft, MS, MS-DOS and Windows are registered trademarks of
Microsoft Corporation.
2. Pentium is a U.S. registered trademark of Intel Corporation.
3. Brands and product names are trademarks or registered trademarks
of their respective companies.

 Quick Start
Installing Driver
You may install HiTi 640DL-Amphi Diver into your PC in the following
steps.
1. Insert “Driver CD” into the CD-ROM drive. If the installation doesn’t
start automatically; execute the “autorun.exe” in the disk.
2. Select “Install HiTi 640DL-Amphi Driver” and install.
3. Click button “Start” to install the driver.

4. Connect printer to PC through USB cable and switch the printer’s
power on.
5. In Windows 2000 or Windows XP, if there’s message dialog showing
“Digital Signature Not Found” or “Driver Incompatibility”, please
click “Yes” to continue installing driver.

 About PhotoDesiree
Installing Software
You may install HiTi PhotoDesire 2 into your PC in the following steps.
1. Insert “Driver CD” into CD-ROM drive, if the installation doesn’t start
automatically; execute the “autorun.exe” in the disk.
2. Select “Install HiTi PhotoDesiree 2” and install.
3. Select language type and destination, then click “Start” button for
installation.

 About PhotoDesiree 2
User Interface
You may learn the HiTi PhotoDesiree 2 user interface from following
instruction diagram.
Image Explorer : Load and explore image files.
Image Preview : Select printer, printout format and portrait or andscape.
Image Editor : Edit selected image.
Print Queue : Save images temporarily for printing.
Image Explorer :
Load and explore image files.
Image Preview :
Select printer, printout format
and portrait or landscape.
Image Editor :
Edit selected image.
Print Queue :
Save images temporarily for printing.

 About PhotoDesiree 2
Printing a Photo
You may printout your first photo from HiTi PhotoDesiree 2 in the
following steps.
1. Load images from a PC, digital camera or scanner.
2. Select “Amphi“, and 4”x6” photo only.
3. Select an image and press triangle button to send selected image to
the editing area.
4. Use [Edit Tool] for more image effects.
5. Send edited images to [Print Queue].
6. Press [Print] Button to start printing.
1
2 3
4
5
6

 Quick Start
Customer Service Claim
 WEB Support
If you need more help, please visit ITCS website, http://www.i-tcs.co.kr.
You can download new drivers, updated applications and more
e-Frames there.
 Customer Support Center
(1) Procedure for ASS
1) Receive request either by phone or e-mail
2) Technical evaluation by ITCS on the problem
3) Door to Door delivery
① Safe packing is recommend with notice of < handle with care >
② Please mark client info including contact / phone number / nature of
defection
③ Address :
#701, Kolon Disital Tower Vilant, 222-7, Guro-Dong, Guro-Gu, Seoul,
Korea
HiTi 640Amphi printer Technical Support Team
Tel : [phone]~8 / Fax : [phone]
Homepage : http://www.i-tcs.co.kr

(2) etc. inquiries
♦
♦ I I- -T TC CS S H Ho om me ep pa ag ge e
Following informations are available in ITCS homepage at www.i-tcs.co.kr
▪ printer
▪ printer driver
▪ Consumables including ribbons and cards
♦
♦ I
I- -T TC CS S Technical Support Team
Please provide following information
▪ Printer serial No.
▪ Name of O/S
▪ Name of O/S
▪ Description on the problems
▪ Initial measures taken by the client