HMS Anybus-X AB7609 User manual

Anybus-X
PROFIBUS to DeviceNet Gateway
Installation Guide
AB7609
Part no. SP0847
Rev. 1.10

Installation Guide 1
© 2005 HMS Industrial Networks.
Table of Contents
Installation Items Checklist ............................................... 2
Installation and operating requirements .......................... 2
Connectors.......................................................................... 3
Connecting Power .............................................................. 3
Connecting to DeviceNet ................................................... 4
DeviceNet Connector ..................................................... 4
....................................................................................... 4
Setting the MAC ID and Baud Rate ............................... 4
Connecting to PROFIBUS .................................................. 6
PROFIBUS Connector ................................................... 6
Setting the PROFIBUS Network Address ...................... 6
Setting the PROFIBUS Baud Rate................................. 6
Setting the PROFIBUS Network Termination................. 6
Configuration Port Connector ........................................... 7
Further Technical Information........................................... 8
Technical Specifications.................................................... 8
Environmental Specifications ......................................... 8
EMC Directive Compliance ............................................ 8
Electrical Specifications.................................................. 8
Mechanical Rating.......................................................... 8
Warranty .............................................................................. 9
Support .............................................................................. 10

AB7609 Installation Guide 2
© 2005 HMS Industrial Networks.
Installation Items Checklist
• Anybus-X ProfiBus to DeviceNet Gateway (part number AB7609).
• Anybus-X ProfiBus to DeviceNet Gateway User Manual downloadable from
http://www.anybus.com and go to the support section
• Power cable for connection to supplied 2 position connector.
• DeviceNet cable for connection to supplied 5 position connector.
• PROFIBUS cable for connection to 9-pin D-Subminiature connector.
• DeviceNet configuration tool such as RSNetworx for DeviceNet or NetTool-
DN.
• PROFIBUS configuration tool.
• EDS file, EDS_ABM_DEV_V_1_3.eds, downloadable from:
http://www.anybus.com and go to the support section.
• GSD file, HMS_1013.gsd, downloadable from http://www.anybus.com and go
to the support section.
Installation and operating requirements
•Power, input and output (I/O) wiring must be in
accordance with Class 1, Division 2 wiring methods
– article 501-4 (b) of the National Electric code,
NFPA 70 and in accordance with local codes.
•Warning – Explosion Hazard – Substitution of
components may impair suitability for class 1,
Division 2.
•Warning – Explosion Hazard – When in hazardous
locations turn off power before replacing or wiring
modules.
•Warning – Explosion Hazard – Do not disconnect
equipment unless power has been switched off or the
area is known to be nonhazardous.
•Terminal tightening torque must be between 5 – 7
lbs-in (0,5-0,8 Nm).
•For use in Class 2 circuits only.
•Suitable for Surrounding temperature of 65 C max.
•Use 60/75 C copper wire only.

AB7609 Installation Guide 3
© 2005 HMS Industrial Networks.
Connectors
Connecting Power
The Anybus-X requires 24 volts DC power on the 2 position terminal block con-
nector.
DeviceNet Power Aux RS-232
PROFIBUS
PROFIBUS
Termination
PROFIBUS
Address
24VDC Common
24 VDC +

AB7609 Installation Guide 4
© 2005 HMS Industrial Networks.
Connecting to DeviceNet
DeviceNet Connector
DeviceNet is connected to the 5 position terminal block connector.
A 120 ohm termination resistor (not provided) between CAN High and CAN Low
may be required for proper network termination.
Setting the MAC ID and Baud Rate
Factory default DeviceNet settings are:
MAC ID 63
Baud Rate 125K
(Red) Net Power 24VDC +
(Black) Net Power 24VDC Common
(White) CAN High
(Blue) CAN Low
CAN Shield

AB7609 Installation Guide 5
© 2005 HMS Industrial Networks.
Setting MAC ID and Baud Rate Using the Anybus-X Configuration Tool
The DeviceNet configuration can be set using the BWConfig tool. When
launched, the tool (shown below) will allow the DeviceNet configuration to be
edited and downloaded to the module. Once the configuration has been down-
loaded, the Anybus-X will be reset automatically by the tool. See the Configura-
tion section of the user manual for complete details on using BWConfig.
Setting MAC ID and Baud Rate Using a Node Commissioning Tool
A DeviceNet node commissioning utility, such as RSNetworx or NetTool-DN,
may be used to change the MAC ID and baud rate settings. Refer to the user doc-
umentation for the tool being used, or the Anybus-X user manual for more details.

AB7609 Installation Guide 6
© 2005 HMS Industrial Networks.
Connecting to PROFIBUS
PROFIBUS Connector
PROFIBUS is connected to the 9-pin D-Subminiature connector located next to
the PROFIBUS termination DIP switch.
Setting the PROFIBUS Network Address
The PROFIBUS network address is set using two rotary switches on the end of the
Anybus-X. Each switch sets a digit of the address from 1 to 9, allowing for a range
of network addresses from 1 to 99.
The rotary switch nearest the 9-pin D-Sub PROFIBUS network connector sets the
10’s digit. The other switch sets the 1’s digit
Hint: If you look at the end of the Anybus-X with the 9-pin D-Sub PROFIBUS
network connector on your left, the node address is easier to read.
Setting the PROFIBUS Baud Rate
The PROFIBUS baud rate is set during the configuration of the PROFIBUS Mas-
ter. The Anybus-X has automatic baud rate detection so no configuration of the
Anybus-X itself is required.
Setting the PROFIBUS Network Termination
If network termination is required at the Anybus-X, set the termination DIP
switch to the ON position.
Note: If an external termination connector is used, the termination switch must be
in the OFF position.
(6) +5V Bus
(3) B-Line
GND Bus (5)
RTS (4)
A-Line (8)

AB7609 Installation Guide 7
© 2005 HMS Industrial Networks.
Configuration Port Connector
The configuration port is the 9-pin D-Subminiature female connector on the end
of the Anybus-X. The connector has a standard RS-232 DTE pin configuration.
The connections to be made are shown in Figure 1..
The Anybus-X is connected to a PC for configuration using a null-modem cable.
A null-modem cable has pins 2 and 3 swapped so that the PC’s Transmit line is
connected to the Anybus-X’s Receive line, and the PC’s Receive line is connected
to the Anybus-X’s Transmit line.
Note: The Anybus-X does not make use of the modem control signals specified
for a DTE connector. Connecting the module through devices, such as isolation
modules, which assume control of these lines may cause the BWConfig commu-
nications to be unreliable.
Figure 1. Configuration Port Connector
(2) Receive Data
(3) Transmit Data
Signal Ground (5)

AB7609 Installation Guide 8
© 2005 HMS Industrial Networks.
Further Technical Information
Complete technical information on installing and configuring the Anybus-X can
be found in the Anybus-X ProfiBus to DeviceNet Gateway User Manual. The User
Manual can be downloaded from the HMS Industrial Networks AB web site at:
http://www.anybus.com and go to the support section
or requested directly using the contact information supplied below.
Technical Specifications
Environmental Specifications
Operating Temperature: 0 to 70 degrees Celsius
Non-Operating Temperature: -25 to 85 degrees Celsius
EMC Directive Compliance
This product is tested to meet the Council Directive 89/336/EC Electromagnetic
Compatibility (EMC) by applying the following standards, in whole or in part,
documented in a technical construction file:
• EN50081-2-EMC Generic Emission Standard, Part 2 - Industrial Environment
• EN50082-2-EMC Generic Immunity Standard, Part 2 - Industrial Environment
This product is intended for use in an industrial environment.
Electrical Specifications
Power Supply: 7-32 VDC.
Current Requirements: 105-110 mA at 24 VDC.
Mechanical Rating
IP20 / NEMA 1

AB7609 Installation Guide 9
© 2005 HMS Industrial Networks.
Warranty
HMS Industrial Networks AB warrants all new products to be free of defects in material
and workmanship when applied in the manner for which they were intended and accord-
ing to HMS Industrial Networks AB’ published information on proper installation. The
Warranty period is one year from the date of shipment.
HMS Industrial Networks AB will repair or replace, at its option, all products returned to
it freight prepaid, which prove upon examination to be within the Warranty definitions and
time period.
Limitation of Liability.
EXCEPT AS EXPRESSLY PROVIDED HEREIN, HMS INDUSTRIAL
NETWORKS AB MAKES NO WARRANTY OF ANY KIND, WHETHER
EXPRESSED, IMPLIED, STATUTORY, OR OTHERWISE. HMS INDUSTRIAL
NETWORKS AB SPECIFICALLY DISCLAIMS ALL IMPLIED WARRANTIES
OF DESIGN, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE,
TITLE AND NONINFRINGMENT. THESE LIMITATIONS SHALL APPLY
NOTWITHSTANDING THE FAILURE OF ESSENTIAL PURPOSE OF ANY
LIMITED REMEDY PROVIDED IN THIS AGREEMENT. NO AGENT OF HMS
INDUSTRIAL NETWORKS AB IS AUTHORIZED TO INCUR WARRANTY
OBLIGATIONS ON BEHALF OF HMS INDUSTRIAL NETWORKS OR TO
EXPAND OR MODIFY THE LIMITATIONS SET FORTH HEREIN.
IN NO EVENT WILL HMS INDUSTRIAL NETWORKS AB OR ITS SUPPLIERS
HAVE ANY LIABILITY TO BUYER FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES HOWEVER
CAUSED AND UNDER ANY THEORY OF LIABILITY (WHETHER IN
CONTRACT, TORT (INCLUDING NEGLIGENCE), INDEMNITY OR
OTHERWISE) WHETHER OR NOT HMS INDUSTRIAL NETWORKS AB HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
IN NO EVENT WILL HMS INDUSTRIAL NETWORKS AB OR ITS SUPPLIERS
HAVE ANY LIABILITY TO THE BUYER FOR ANY LOST PROFITS, LOSS OF
DATA, LOSS OF USE, OR COSTS OF PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES, EXCEPT IN CASES OF WILLFUL MISCONDUCT BY
HMS INDUSTRIAL NETWORKS AB.