Hobby King ME-163 User manual

ME-163
OPERATING MANUAL

WARNING
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product
operating. Failure to operate the product correctly can result in damage to the product, personal before
property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense
and enquires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner
could result in injury or damage to the product or other property. This product is not intended for use by
children without direct adult supervision.
This manual contains instructions for safety, operation and maintenance. It is essential to read and follow
all the instructions and warnings in manual, prior to assembly, setup or use, in order to operate correctly
and avoid damage or serious injury.
!
Safety Precautions and Warnings
As the user of this product, you are solely
yourself and others or result in damage to the product or the property of others. This model is controlled
by a radio signal subject to interference from many sources outside your control.This interference can
cause momentary loss of control so it is advisable to always keep a safe distance in all directions around
your model, as this margin will help avoid collisions or injury.
responsible for operating in a manner that does not endanger
Age Recommendation: Not for children under 14 years. This is not a toy.
• Never operate your model with low transmitter batteries.
•Always operate your model in an open area away from cars, traffic or people.
• Avoid operating your model in the street where injury or damage can occur.
• Never operate the model in the street or in populated areas for any reason.
• Carefully follow the directions and warnings for this and any optional support equipment (chargers,
rechargeable battery packs, etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the reach of children.
• Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed
• Never lick or place any portion of your model in your mouth as it could cause serious injury or even death.
and protected for this purpose.
1

Installing the main wing
2.1. Apply glue on the combined side
of the .main wing
2.2. Apply glue on the combined side
of the .fuselage
1. Install the rocker.
3. Install the . main wing
2
1.1 1.2
2.1 2.2
3.1 3.2

Installing the rudder
3. Install the . rudder
2.1. Apply glue on the combined side
of the .main wing
2.2. Apply glue on the combined side
of the .fuselage
3
3
2.2
2.1
1. Install the rocker.
1

Installing the propeller
1. Install the . propeller 2. Install the .nut
4. Install the .propeller cover
3.Locking the propeller.
5.Locking the propeller cover.
4
1
4
5
2
3

3. Apply glue on the combined side
of the .antenna
Installing the canopy
5. Install the . canopy
2. Connect power battery, adjust the
elevator and rudder.
1. Battery position.
4. Install the . antenna
5
5
4
3
12
9mm
6.When the plane takes off, the aircraft
should be horizontal throwed, and
ailerons on both sides to pull up.

: 900mm /35.4 in
: 600mm /23.6 in
: 770-800g /27.2-28.2 oz
: 57mm
: 4S 2200mA 30C-50C Li-Po Battery
: 80A
: 2850-3500kv
2
: 12.2dm
2
: 65g/dm
: 4 Channel, 3 Servos
And 1 Brushless ESC
: 4 inches
Wingspan
Length
Weight
CG Position
Battery
ESC
Motor
Wing Area
Wing Load
RC System
Propeller
Specification
Center Of Gravity(C.G.)
Main specification
6
73mm
when the voltage lower than 2.9V,the motor will be high to low speed cyclic
2-3 times,remind that into half speed status,it is normal function

Spare Parts List
Rudder
Canopy
Fuselage
Glue Propeller
9g Servo
Sticker
Spinner
Brushless Motor
Brushless ESC
7
Main Wing Set

Extra propeller nosie
or extra Vibration.
Reduced flight time or
aircraft underpowered.
Control surface does
not move, or is slow to
respond to control
inputs.
Control reversed.
Motor loses power.
Motor power pulses
then motorloses power.
LED on receiver
flashes slowly.
Damaged spinner, propeller.
motor or motor mount.
Loose propeller and spinner
parts.
Propellor installed backwards.
Flight battery charge is low.
Propeller installed backward.
Flight battery damaged.
Control surface, control horn,
linkage or servo damage, Wire
damaged or connections loose.
Channels need be reversed
in the transmitter.
Damage to motor, or battery.
Lose of power to aircraft.
ESC uses default soft Low
Voltage Cutoff(LVC).
Power lose to receiver.
Aircraft will not
respond to the
throttle but responds
to other controls.
ESC is not armed.
Throttle channel is reversed.
Lower throttle stick and throttle
trim to lowest settings.
Reverse throttle channel on
transmitter.
Replaced damaged parts.
Tighten parts for propeller
adapter, propeller and spinner.
Remove and install propeller
correctly.Completely recharge
Flight battery.
Remove and install propeller
correctly. Replace flight battery
and obey flight battery
instructions.
Replace or repair damaged
parts and adjust controls.
Do a check of connections for
loose wiring.
Do the Control Direction Test
and adjust controls
for aircraft and transmitter.
Do a check of batteries,
transmitter, receiver, ESC,
motor and wiring for damage
(replace as needed).
Land aircraft immediately and
Recharge flight battery.
Check connection from ESC to
receiver.
Check servos for damage.
Check linkages for binding.
Possible Cause Solution
Problem
Battery Selection and Installation.
1. We recommend the 2200mA Li-Po battery.4S
2. If using another battery, the battery must be at least a 4S 2200mA battery.
3. Your battery should be approximately the same capacity ,dimension and wight as the
4S 2200mA Li-Po battery to fit in the fuselage without changing the center of gravity
Trouble shooting
8

12. Find a safe and open area.
2.Charge fl ight battery.
3.Read this instruction manual thoroughly.
4.Fully assemble model.
5.Install the flight battery in the aircraft ( once it has been fully charged ).
6.Bind aircraft to your transmitter.
7.Make sure linkages move freely.
9.Perform the Control Direction Test with the transmitter.
10. Adjust light controls and transmitter.
11. Perform a radio system Range Check.
1. Remove and inspect contents.
8. Make sure the rubber ring has been properly slide on the clevis.
First Flight Preparation
Take off and landing tips
1. Take off using full power, as soon as you have taken off retract the landing gear.
2. Use the flaps to give a steeper landing approach, increase throttle slightly to offset the
increased drag.
3. Ensure that you set a timer and land with plenty of battery power in reserve.
4. It's difficult to landing the plane perfect from the speedy flying state when the flaps
keep in the contour.
5. Never exceed 3 minutes to fly with the maximum power others.
6. Never exceed the limited flying weight.
Please read the following instructions and fully understand it.
3. Children under the age of 12 should have an adult guide. Never recommend for the children
under the age of 14.
4. Never leave the charger in wet conditions.
1. Do not fly in strong wind or bad weather.
2. Never fly the model in crowded areas, where there are lots of people, automoblies on the
road or power lines overhead . Also do not to fly around the airport. Please make yourself
enough room for the flying and operating, as the plane can travel at high speed. Remember
you are responsible for the safety of others.
9
Flying Tips
5. The is made from PA and polythene which are tinder. When it meets the heat,
transfiguration can easily happen, so you must keep it away from heat.
ME-163
6. Do not attempt to catch the while flying, please do not touch the propeller.ME-163
7. Never leave this system unattended around children with battery in the unit, as injury may
be caused due to children's turning on the transmitter or the plane.
8. During the preparation for the flight, please remember to turn on the transmitter before
connecting the battery pack.
9. Close the throttle on the transmitter before connecting battery otherwise the motor may operate.