Hochiki S772 Technical manual

Version 1.00 |March 2021 |MAN-1420HA
16 Channel IO Panel Module
(S772) Information Guide

CONTENTS
Contents 2
Compliance 4
Underwriters Laboratories (UL) 4
FCC 4
Installation 4
Introduction 5
Technical Support 5
Return Material Authorization (RMA) 5
Warranty Service 6
Advanced Replacements 6
Overview 7
Use Case Examples 7
Package Contents 8
Installation 9
Before You Begin 10
Setting the Address 10
Placement 10
Wiring 13
Inputs 13
Outputs 14
Restrictions 15
Testing the Installation 16
Configuration 17
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 2
Contents

Panel Module Properties 17
Channel Properties 18
For channels set as Outputs 18
For channels set as Inputs 20
ULCompliance Limitations 21
Specifications 22
Electrical 22
Operating Environment 22
Physical Specifications 22
Index 23
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 3
Contents

COMPLIANCE
Underwriters Laboratories (UL)
Fire Alarm Subassembly
Hochiki America Corporation
FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the Installation Manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense. Any
changes or modifications not expressly approved by Hochiki America Corporation could void the user's authority
to operate this equipment under the rules and regulations of the FCC.
Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Installation
Install this product in accordance with NFPA 13, NFPA 72, NFPA 70, and NEC 70 and all local codes.
All field wiring should be installed using fire rated cables according to the NFPA 72. Riser conductors shall be
installed in accordance with the survivability from attack by fire requirements in National Fire Alarm Code, NFPA
72, Section 12.3. Riser conductors shall employ either a 2 hour rated cable system, or meet requirements
approved by the AHJ.
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 4
Compliance

INTRODUCTION
Technical Support
For technical support, contact Hochiki America at 800.845.6692 or [e-mail]. Hochiki
technical support is available Monday through Friday, 7:00AM to 5:00PM, PST.
Prior to contacting technical support, have the following information available:
nProduct part number
nPurchase order or order number
nProduct serial number
nCurrent function of the product
nExpected function of the product
nInstallation of the product
Return Material Authorization (RMA)
Contact Technical Support to obtain an RMAfor any product to be returned. Returns will not be accepted
without an accompanying RMA number. An RMA number is assigned when:
lTech Support acknowledges a possible product failure.
lA product was damaged during shipping
lAn incorrect product was shipped
lAn order was placed using an incorrect part number *
lAn order was placed using an incorrect part quantity *
lAn order is no longer required *
* Restocking fees may apply.
All returned products are tested to confirm operating failures experienced in the field. If the product is found to be
functional, contractors must absorb expenses for return shipping, as well as the cost and shipping of the
advanced replacement product.
Prominently display the RMA number on all packages sent for return.
Ship all return products to:
Attention: RMA # _____________
Hochiki America
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 5
Introduction

7051 Village Park Drive, Suite 100
Buena Park, CA90621
Warranty Service
Technical Support can replace or repair a defective product when the original purchase is within the warranty
period defined in the sales contract. Check your contract for more information, or contact your sales
representative about your specific warranty period.
Advanced Replacements
Products that fail to operate in the field can be replaced quickly using the advanced replacement process. The
advanced replacement process is available to all contractors who maintain an acceptable line of credit.
Initiate the advanced replacement process by requesting an RMA number from a Tech Support representative.
Advanced replacements can be shipped to your location when the product is covered under warranty and when
a replacement product is in stock.
lAdvanced replacements can be expedited at the request of the contractor. Shipping costs associated with this
process are the responsibility of the contractor.
lProducts returned using the advanced replacement process must be received within 30 days of the RMA issue date.
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 6
Introduction

OVERVIEW
16 Channel I/OPanel Module (S772)
The 16 Channel I/O Interface enhances the versatility of the alarm system by providing additional input and
output capabilities to the FireNET L@titude Fire Alarm ControlPanel. Inputs and outputs can be selected for up
to 16 individual channels. All inputs and outputs are configured in the same way as devices connected to
addressable loops of the panel. The 16 Channel I/O Interface can be configured to contribute or act upon cause
and effect logic.
Use Case Examples
The 16 Channel I/OInterface can be used to interface the L@titude panel to a NAC extender or Voice
Evacuation system, by providing
linputs to the L@titude panel for dry contact closures such as General Trouble, AC Power Trouble, or Battery Trouble
from these devices.
loutputs from the panel to control various NAC or Voice Evacuation outputs.
The 16 Channel I/OInterface can be used to interface the L@titude panel to a secondary panel or releasing
panel, by providing
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 7
Overview

linputs to the L@titude panel for dry contact closures such as Fire, Supervisory, and Trouble from these panels, and
various stages of release from the releasing panel.
loutputs from the panel to activate NAC outputs on these panels.
IMPORTANT! Refer to the Wiring section for restrictions when using and wiring the 16 Channel I/O Panel Module.
Package Contents
l(1) Installation sheet
l(1) Wiring Terminal Labels
l(1) S772 16 Channel I/O Interface
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 8
Overview

INSTALLATION
This section provides instructions for connecting cables, mounting, and testing the 16 Channel I/OPanel Module
for installation.
qUsing Loop Explorer 2, add the panel module to the existing configuration and configure it as required for the
system. For detailed information on the configuration settings, refer to the Configuration section.
qNotify the monitoring center and location security that the FireNET L@titude Fire Alarm ControlPanel will be
temporarily out of service.
qRemove the module from its packaging and check its contents.
qSet the address of the module as configured in Loop Explorer 2. Refer to Setting the Address for details.
qDetermine the slot (E or higher) where the panel module will be installed and place the provided sticker label on the
corresponding field terminals.
qConnect field wiring as shown in the Wiring section below.
qTransfer the new configuration from Loop Explorer 2 into the panel.
qWait for the "Sending configuration to panel" (in LE2) and "Saving configuration" (on the panel) steps to complete.
qRemove AC and battery power from the panel.
qRemove the black plastic cover.
qInstall the module into selected slot on the Main Back Board or an Extension Board of the panel.
qRestore AC and battery power.
qWait for the panel start-up process to complete. Refer to the FireNET L@titude Fire Alarm ControlPanel
Installation Manual (MAN-1431HA) for more information.
qTest communication from the panel via the LEDStatus Indicators
qResolve any troubles related to the new connections.
qActivate each circuit and verify that all connected devices function properly.
qReplace the black plastic cover.
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 9
Installation

Install this product in accordance with NFPA 72, the National Electrical Code, and all local codes.
WARNING! The module must be installed by personnel familiar with electronic components. Electronic
components within the module are vulnerable to damage from electrostatic discharge. Ground straps must be worn by
installers before handling to prevent electrostatic discharge damage.
Before You Begin
The following item is not included with the FireNET L@titude Fire Alarm ControlPanel, but is required for the
installation:
lA Ground Strap is required for handling circuit boards.
Setting the Address
Panel modules should use addresses 1-8. Each panel module of the FireNET L@titude Fire Alarm
ControlPanel must contain a unique setting before being connected to the Main Back Board. The binary setting
of the DIP switch sets the specific address for the panel module. The numeric order of the address setting
between modules does not impact operation, but each panel module must be assigned a separate / unique
address.
The black portion of the DIP switch identifies the switch actuator.
Placement
To install modules on the FireNET L@titude Fire Alarm ControlPanel:
Hochiki America Corporation
16 Channel IO Panel Module (S772) Information Guide
Version 1.00 |March 2021 |MAN-1420HA
Page 10
Installation