Hocom BCS Series User manual

BCS
Series
User Manual

CAUTION
Always assemble the platter onto the scale before
switching on the scale.
Never leave the scale with something placed on
the platter for a long period.
Please prevent the scale from high temperature,
humidity, press and bump.
Please locate the scale in a flat and plane surface.
Users can adjust four rubber-cushions and make
the level-balance fixed on the center stably.
If the scale is covered with dust, wipe it with soft
cloth slightly. Please use neutral detergent only.
The stainless steel platter and plastic platter can
be cleaned with water. Please dry them before
using.
Please recharge the battery after a long period of
storage (more than ONE month).
1
BCS-Coin Counting Scale User Manual

DIMENSION
BCS
2
BCS-Coin Counting Scale User Manual

DISPLAY
ZeroIndicator (ZERO):
Switch on the scale. Normally, the scale will adjust
to zero point automatically and the cursor will
appear on VALUE/QUANTITY Display (at the right of
ZERO). If not, press [ZERO] key to adjust the scale
at zero point.
NetWeightIndicator (TARE):
Place the container or package on the platter and
then press [TARE] key. The cursor will appear on
VALUE/QUANTITY Display (at the right of TARE).
Then users can read the net weight of measured
subjects with packages or containers.
AccumulatingIndicator (ADD+):
When users use [ADD+] key to save the measured
weight and value/quantity into the memory bank, the
cursor will appear on VALUE/QUANTITY Display
(at the left of ADD+). Press [TOTAL CLEAR] key, this
cursor will disappear.
3
BCS-Coin Counting Scale User Manual

SHIFT-ModeIndicator(SHIFT):
Press [SHIFT] key to enter SHIFT mode. The 
cursor will appear on VALUE/QUANTITY Display (at
the left of SHIFT). Press [SHIFT] key again to go
back to normal operation mode, and the cursor will
disappear.
Quantity-ModeIndicator (QTY):
Press [VALUE/QTY] key to switch the scale between
QUANTITY-Mode and VALUE-Mode. The 
cursor will appear on VALUE/QUANTITY Display (at
the left of QTY)when the scale is switched to
QUANTITY-Mode.
NOTICE!!
The internal resolution (accuracy) of this scale is
30000. However, we strongly suggest that the
minimum unit weight of measured coins /
subjects must not be less than the
sensitivity/minimum capacity. (for BCS-15kg
x 2g, the unit weight of each coin should not be
less than 2g).
4
BCS-Coin Counting Scale User Manual

KEYBOARDOPERATIONS
0~9:
(1) Under normal operation mode:
Standard preset keys for ZAR coin –
R5-NEW(9.480g/pce)、R1(3.994g/pce)、
R2(5.492/pce)、R5-OLD(6.987g/pce)、
10c-OLD(1.982/pce)、20c(3.488g/pce)、
50c(4.961g/pce)、、1c(1.496g/pce) 、
2c(3.006g/pce) 、5c(4.476g/pce)、
Convert to NAD coin –:
R1(4.964g/pce)、R5-OLD(6.120/pce)、
10c-OLD(3.3926g/pce)、50c(4.4003g/pce)、
5c(2.1941/pce)
NOTICE: Press SHIFT to check these Value
(2) Under SHIFT-Mode: 0~9 numeral keys
:
(1) Under normal operation mode:
10c-NEW(1.991g/pce) for ZAR coin
N$ 10(8.991g/pce) for NAD coin
(2) Under SHIFT-Mode: Press this key to set the
decimal point.
CLEAR: This key is for clearing the figures that is
showed on DENOMINATION Display.
5
BCS-Coin Counting Scale User Manual

VALUE/QTY:This key is for switching the scale
between QUANTITY-Mode and VALUE-Mode.
SHIFT:This key is for entering SHIFT-Mode.
Press [SHIFT] key again to go back to normal
operation mode.
ZERO:This key is for adjusting the scale at zero
point. The cursor will appear on
VALUE/QUANTITY Display (at the right of ZERO).
TARE: This key is for getting the net weight value;
please place a package or container on the platter
and press [TARE] key.
e.g.: If the package is 200g, WEIGHT Display will
show –200 after users take the package away
from the platter.
ADD+: This key is for saving the measured weight
and value/quantity into the memory bank. Please
be reminded that ADD+ function must be operated
under the same kind of coin and the same
operation mode (QUANTITY or VALUE).
Otherwise, the result of total accumulation will be
meaningless and incorrect.
5
6
BCS-Coin Counting Scale User Manual

TOTAL: This key is used to recall the total
accumulation of quantity or value (on VALUE /
QUANTITY Display). Press [TOTAL] key again to
go back to normal operation mode.
TOTAL CLEAR:This key is for deleting all the
accumulation data in the memory bank.
value: This key is for setting the denomination value
of sampling coins under SHIFT-Mode.
pcs:This key is for setting the quantity value of
sampling coins under SHIFT-Mode.
uw:This key is for setting the unit weight value of
sampling coins under SHIFT-Mode.
NAD: This key is for converting coins between
ZAR and NAD coins.
The coins for ZAR and NAD could be preset when
power on the scale:
1. Press TOTAL key and do not release your finger when power on
the scale. The display will show the version of scale.
2. Press and hold TOTAL CLEAR key till the display shows SEtUP,
then press 3 key twice, the display will flash good twice.
3. Setting is finished.
7
BCS-Coin Counting Scale User Manual

BatteryCHARGE
When LCD indicates , the battery is in
low-voltage condition. Please recharge the battery as
soon as possible. Please power off the scale and
connect the power cord to an AC outlet. CHARGE
LED will indicate the ongoing status of the battery. It
takes about 8~10 hours to fully recharge the battery.
CHARGE LED:
Color of LED
Status of the battery
RED
Charging
GREEN
Fully-charged
POWERSUPPLY
AC : 220V±10%, 50Hz
DC : 6V/4Ah rechargeable battery;
P=0.2W(max)
8
-
BCS-Coin Counting Scale User Manual

We do more than you expect
COIN COUNTING SCALE