Hocom SSW Series User manual

SSW - Weighing Scale
User Manual
User Manual
SSW
Series
DIGITAL WEIGHING SCALE

SSW - Weighing Scale
User Manual
Cautions
Upon receiving the scale, please take at least 8
hours to recharge the battery before you start to
operate this scale.
Please recharge the battery after a long period of
storage (more than one month). It takes 8~10
hours to fully recharge the battery.
Please assemble the platter before powering on
the scale.
Do not keep the weight placed on the platter for a
long period.
Keep the scale away from the environment with
high temperature, high humidity, heavy press,
and heavy bump.
Always make sure the scale is located in a flat
and plane surface.
1

SSW - Weighing Scale
User Manual
Dimensions

SSW - Weighing Scale
User Manual
Symbols on LCD
Zero Symbol (O):
Oappears on the left-bottom corner of LCD, and
indicates the scale is at zero-point.
NET Weight Symbol (Net):
Net appears on the bottom edge of LCD, and
indicates the tare weight has been deducted.
Battery Symbol ( ) :
When LCD indicates and the scale sounds
beep for four times, it means the battery is running
in low-voltage status. LCD will indicate
continuously for reminding the user to recharge the
battery. If the battery is still running in low-voltage
status without being recharged, LCD will indicate
-OFF- and the scale will sound beep for eight times.
Please power off the scale and recharge the battery
immediately.
-
2
3
-
-

SSW - Weighing Scale
User Manual
Operation Instructions
Backlight (optional) :
Press and hold key till the scale sounds
beep to enable / disable the Backlight.

UNIT:
Select the weight mode: kg / pcs.
Under pcs (simple counting) mode:
!! The suggested unit weight of the measured
subject should be heavier than the division of
this scale.
1. Put 100 pieces of the measured subject (with the
same unit weight) on the platter.
2. Press and hold [UNIT] key till LCD shows S= 10,
and then quickly (within 3 seconds) press [UNIT]
key again to select S=100 (10、20、50、100 could
be selected for the sample-quantity of the
measured subject).
3. Wait till LCD shows 100. The scale has finish
calculating the averaging unit weight of the
measured subject. Now the simple counting
function is ready. This scale could be used as a
simple counting scale.
4

SSW - Weighing Scale
User Manual
 :
Press this key to make the scale be at zero point.
LCD will indicate O on the left-bottom corner.

:
Press this key to deduct the tare weight. Put the
package or container on the platter and then press
[TARE] key. LCD will show O and Net.
5

SSW - Weighing Scale
User Manual
RS232 Interface Connection: <optional device>
RS232 Wiring Configuration:
Baud Rate: 9600
Parity: None
Stop Bit: 1
Data Bit: 8
5
4
3
2
1
9
8
7
6
PC
5
4
3
2
1
9
8
7
6
SCALE
GND
6
DATA OUT

SSW - Weighing Scale
User Manual
Recharge the Battery
Power off the scale and connect the power cord to
an AC outlet. CHARGE LED will indicate the
ongoing status of the battery. It takes about 8~10
hours to fully recharge the battery.
CHARGE LED:
Color of LED
Status of the battery
RED
Initial connection
ORANGE
Charging
GREEN
Fully-charged
Power Requirements
AC: 220V±10%, 50 Hz
DC: 6V/4Ah rechargeable battery;
P=0.2W(max)
7

SSW - Weighing Scale
User Manual
5
1
8
2
3
4
6
7
List of Components:
No.
Item
<1>
Indicator
<2>
Regulator
<3>
Stainless Steel Tube
<4>
Tube Base
<5>
Stainless Steel Platter
<6>
Main Structure
<7>
Cable of Load Cell
<8>
Connector
Installation Diagram of Bench Scale
Installation Procedure:
A. Screw <4>Tube Base and <6>Main Structure together (with 2
screws of Tube Base).
B. Insert <3>Stainless Steel Tube into <4>Tube Base (with 2 screws of
Stainless Steel Tube).
C. Screw <2>Plastic Regulator and <3>Stainless Steel Tube together
(with 1 screw and 1 clip of Regulator).
D. Please refer to the Diagram; pull <7>Cable of Load Cell, from the
bottom to the top, through <3>Stainless Steel Tube; and then screw
the Clip on the bottom of <4>Tube Base (with 1 screw of Clip).
E. Connect <1>Indicator with <2>Regulator. Notice the d
irection.
Please refer to the arrow on the diagram for proper direction.
F. Put <5>Stainless Steel Platter on <6>Main Structure.
G. Insert <8>Connector into the socket of <1>Indicator. Complete
installation.
※
Before using this scale, please unscrew the protecting-screw
fixed on the bottom side of the steel-welding base structure.
8

SSW - Weighing Scale
User Manual
We do more than you expect
DIGITAL WEIGHING SCALE