Hocom TAP Series User manual

TAP-Pricing Scale
User Manual
User Manual
TAP Series
DIGITAL PRICING SCALE

TAP-Pricing Scale
User Manual
Cautions
Upon receiving the scale, please take at least 8 hours
to recharge the battery before you start to operate
this scale.
Please recharge the battery after a long period of
storage (more than one month). It takes 8~10 hours
to fully recharge the battery.
Please assemble the platter before powering on the
scale.
Do not keep the weight placed on the platter for a
long period.
Keep the scale away from the environment with high
temperature、high humidity、heavy press、heavy
bump.
Always make sure the scale is located in a flat and
plane surface.
1

TAP-Pricing Scale
User Manual
Dimensions
The below panel & keyboard are suitable for table
scale / indicator / bench scale.
2

TAP-Pricing Scale
User Manual
Symbols on LCD
ZERO Indication ():
Cursor appears on the WEIGHT LCD Display (above
of ZERO printed on the display-overlay), and indicates
the scale is at zero-point.
NET Weight Indication ():
Cursor appears on the WEIGHT LCD Display (above
of NET printed on the display-overlay). This cursor
indicates the tare weight that has been deducted.
Accumulation Indication ():
Cursor appears on the WEIGHT LCD Display(above
of M+ printed on the display-overlay), and indicates the
memory bank that has stored accumulative data of
weight, unit price, and total price.
Indication of Weighing Range () :
Cursor appears on UNIT PRICE LCD Display, (above
of W1 or W2 printed on the display-overlay), and
indicates the present weighing range to be Weighing
Range 1 (W1) or Weighing Range 2 (W2).
!! Notice:The indication of weighing range is only
available for the scale with multiple range (2 ranges)
3

TAP-Pricing Scale
User Manual
Indication of kg、100g Weighing Unit () :
Cursor will flash on the UNIT PRICE LCD Display
(above of kg, 100g printed on the display-overlay). This
cursor indicates the present weighing unit.
Battery Symbol () :
When LCD indicates and the scale sounds beep
for four times, it means the battery is running in
low-voltage status. LCD will indicate continuously
for reminding the user to recharge the battery. If the
battery is still running in low-voltage status without being
recharged, LCD will indicate -OFF- and the scale will
sound beep for eight times.Please power off the scale
and recharge the battery immediately.
-
4
-
-

TAP-Pricing Scale
User Manual
Operation Instructions
 0 ~ 9 :
Press these keys to key in the unit price.
:
(1) Press this key to set the decimal point for the unit
price.
(2) Press and hold [] key till the scale sounds beep to
enable or disable optional Backlight.
 CE :
Press this key to delete the setting of unit price. Users
could key in the unit price directly without pressing [CE]
key while the last transaction had been finished for more
than 3 seconds.
:
Press this key once, WEGIHT LCD Display will indicate
chg -, and then press [1] or [2] key to select the
weighing unit:
Press [1] key to select kg unit.
Press [2] key to select 100g unit.
5
UNIT
SET

TAP-Pricing Scale
User Manual
:
(1) Press this key to make the scale be at zero-point.
WEIGHT LCD Display will indicate cursor on the
above of ZERO (printed on the display-overlay).
(2) Press this key could get the net weight. Place a
package or container on the platter and press this key
to deduct the tare weight, WEIGHT LCD Display will
show 0.000 and indicate cursors on the above of
ZERO and NET printed on the display-overlay.
+:
Press this key to operate the non-weighing items. Key in
a unit price and then press [+] key to save the figure into
the memory bank, then show the accumulation amount.
 X :
Press this key to operate the multiplication.
Example: Key in 25 »Press [x] key »Press 3»
TOTAL PRICE LCD Display will indicate 75.00
(25 x3 = 75).
At this moment, press [+] key could save this figure into
the memory bank, or press [CE] key to delete this figure.
6
TARE
ZERO

TAP-Pricing Scale
User Manual
 M+ :
Press this key could save the measured weight, unit
price, and total price into the memory bank (up to 99 data
accumulation).
 MR :
Press this key to recall the data (16 data recall) one by
one that is saved in the memory bank by press [M+] or [+]
key. When the last data is showed, press [MR] key again
will get the total accumulated price on TOTAL PRICE
LCD.

CHANGE :
Press this key to operate money-change function.
Example:
When TOTAL PRICE LCD Display shows $17.15, and
the customer gives $20.00. Press [CHANGE] key once,
and then key in 20. LCDs will show:
WEIGHT
20 (amount from the customer)
UNIT PRICE
17.15 (total amount of transaction)
TOTAL PRICE
C 2.85 (return to the customer)

MC :
Press this key could delete all accumulated data in the
memory bank (the scale will sound beep beep when
[MC] key has been operated).
7

TAP-Pricing Scale
User Manual
RS232 Interface Connection:<optional device>
RS232 Wiring Configuration:
Baurate: 9600
Parity: None
Stop Bit: 1
Data Bit: 8
GND
5
4
3
2
1
9
8
7
6
5
4
3
2
1
9
8
7
6
8
DATA OUT

TAP-Pricing Scale
User Manual
Recharge the Battery
Power off the scale and connect the power cord to an
AC outlet. CHARGE LED will indicate the ongoing
status of the battery. It takes about 8~10 hours to fully
recharge the battery.
CHARGE LED:
Color of LED
Status of the battery
RED
Initial Connection
ORANGE
Charging
GREEN
Fully-charged
Power Requirement
AC: 110V±10%, 60Hz
DC: 6V/4Ah rechargeable battery;
P=0.2W(max)
9

TAP-Pricing Scale
User Manual
10
Installation Diagram of Bench Scale
List of Components:
No.
Item
<1>
Indicator
<2>
Regulator
<3>
Stainless Steel Tube
<4>
Tube Base
<5>
Stainless Steel Platter
<6>
Main Structure
<7>
Cable of Load Cell
<8>
Connector
5
1
8
2
3
4
6
7
Installation Procedure:
A. Screw <4> Tube Base and <6> Main Structure together (with 2 screws
of Tube Base).
B. Insert <3> Stainless Steel Tube into <4> Tube Base (with 2 screws of
Stainless Steel Tube).
C. Screw <2>Regulator and <3> Stainless Steel Tube together (with 1
screw and 1 clip of Regulator).
D. Please refer to the Diagram; pull <7> Cable of Load Cell, from the
bottom to the top, through <3> Stainless Steel Tube; and then screw
the Clip on the bottom of <4> Tube Base (with 1 screw of Clip).
E. Connect <1> Indicator with <2> Regulator. Notice the direction.
Please refer to the arrow on the diagram for proper direction.
F. Put <5> Platter on <6> Main Structure.
G. Insert <8>Connector into the socket of <1>Indicator. Complete
installation
※
Before using this scale, please unscrew the protecting-screw fixed
on the bottom side of the steel-welding base structure.

TAP-Pricing Scale
User Manual
We do more than you expect
DIGITAL PRICING SCALE