Hodedah HI29-A User manual

1 | P a g e
www.Hodedah.com
Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
ITEM # HI29-A
2 DOOR WARDROBE
FRONT VIEW BACK VIEW
Product Dimensions: Height 72” x Width 32” x Depth 17”
Weight Capacity Per Drawer 20 lbs.
2 people
60mins
1 YR LTD
1 Box

2 | P a g e
www.Hodedah.com
Questions, need parts, we are here to help!
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
DO NOT RETURN PRODUCT TO THE STORE
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
______________________________________________
WARRANTY
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
WARNING
This product contains small parts, keep away from children.
This product contains plastic bags, keep away from children.
Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
Never allow children to climb or hang on drawers, shelves and doors.
Never open more than one drawer at a time.
The use of tip-over restraints may reduce but not eliminate the risk of tip-over.
Phone
Mon –Fri | 9:30 am to 5pm EST
1 - 855 –HODEDAH
1 –855 –463 -3324
Email
Send us an email
[email protected]
Website
Visit our website to open a case
www.Hodedah.com

3 | P a g e
www.Hodedah.com
Let’s get started…
Helpful hints, read before beginning assembly
Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
Work in a spacious level area, preferably carpet, near the place the unit will be used.
DO NO USE power tools to assemble your furniture, it will strip and damage parts.
Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Assembly Tools Required (not supplied)
Hammer Phillips Screwdriver Tape Measure No Power Tools Needed
____________________________________________________________________________________
Product Care and Maintenance
Wipe clean with dry soft cloth, never use chemicals or cleaning products that will
damage the finish.
Avoid placing your furniture in direct sunlight, as sunlight causes fading.
Never push, drag or pull your furniture, to move to a new location carefully with two or
more people carry the unit to its new location.
Avoid extreme changes in temperature by arranging furniture away from radiators, heat
and air vents and air conditioning units.

4 | P a g e
www.Hodedah.com
Hardware List
A
PVC Dowel
QTY
31Pcs
B
Minifix
QTY
6Sets
C
Screw
M4x45mm
QTY
28Pcs
D
Screw
M3.5x16mm
52Pcs
E
Screw
M3.5x21mm
12Pcs
F
Nail
30Pcs
G
Aluminum Pipe
(760x19mm)
1Pc
H
Handle (96mm)
6Pcs
I
Drawer Slide(300mm)
2Sets
J
Hinges 2/8
4Pcs
K
V –Bracket
2Pcs
L
Sticker
14Pcs
M Nail Leg
5Pcs
Important
1. Before you throw the package, please use the Check Box to identify the parts and hardware to
ensure that you have everything you need.
2. Check and measure the bolts before applying them to parts.
3. Do not completely tighten all hardware until the entire assembly is complete, unless indicated
otherwise.

5 | P a g e
www.Hodedah.com
Parts List
1Top Panel
800x425x15mm
QTY
1Pc
2 Left Side Panel
1800x400x15mm
QTY
1Pc
3 Right Side Panel
1800x400x15mm
QTY
1Pc
4 Front
Strengthening Panel
766x70x15mm
1Pc
5 Back Strengthening
766x70x15mm
1Pc
6 Back Panel
766x400x75mm
1Pc
7 Kick Panel
766x100x15mm
1Pc
8 Partition Panel
766x400x15mm
1Pc
9 Door Panel
1214x388x15mm
2Pcs
10 Drawer Front
Panel
780x238x15mm
2Pcs
11 Drawer - Left Side
Panel
300x128x15mm
2Pcs
12 Drawer - Right
Side Panel
300x128x15mm
2Pcs
13 Drawer End
Panel
709x128x15mm
2Pcs
14 Drawer Base
Panel
718x294x2.5mm
2Pcs
15 Drawer Base
Supporting Panel
285x50x15mm
2Pcs
16 Back Panel
1450x396x2.5mm
2Pc
17 Kick Panel
766x70x15mm
1Pc

6 | P a g e
www.Hodedah.com
The Breakdown…
1
10
3
2
16
16 4
5
8
6
7
17
9
10
12
11
13
14
15
12
11
13
14
15
9

7 | P a g e
www.Hodedah.com
In hardware list, you will find two bundles of drawer slide (I), here you need
to differentiate left and right as shown in picture below.
Left Drawer Slide(I)
Flat Shaped - Left
"L" Shaped - Left
Right Drawer Slide(I)
Flat Shaped - Right
"L" Shaped - Right

8 | P a g e
www.Hodedah.com
Step 1
*Insert PVC dowel (A) to panel 2, 3, 4, 5, 6, 7, 8, 11, 12 and 17's into the
holes as shown, using hammer to gently tap them in.
3
4
2
5
6
8
17
7
12
12
11
11

9 | P a g e
www.Hodedah.com
Step 2
K
2
Fasten V-Bracket
(K) on panel 2
and 3 as shown
by using 2
screws (D).
Place the flat shaped - left
of the drawer slide (I) at
the panel 2 as shown.
Then tighten each drawer
slide(I) with 3 screws (D).
I
3
Place the flat shaped - right of
the drawer slide (I) at the
predrilled holes on the panel 3
as shown. Then tighten each
drawer slide (I) with 3 screws
(D).
I
D

10 | P a g e
www.Hodedah.com
Step 3
*Place and fix panel 4, 5, 6, 7, 8 and 11 onto panel 2 by inserting the (Left)
dowels onto the non-thru holes at panel 2 by slightly tapping them with
hammer.
*Insert and fasten screws (C) (Using predrilled holes on panel 2) into the
panel 4, 5, 6, 7, 8 and 17.
4
2
5
8
7
6
17

11 | P a g e
www.Hodedah.com
Step 4
*Fix panel 3 onto panels 4, 5, 6, 7, 8 and 17 by inserting the (Right) dowels
onto non-thru holes on panel 3 by slightly tapping them with hammer.
*Fasten screws (C) from outside of panel 3, using the predrilled holes to
attach panels 4, 5, 6, 7, 8 and 17.
*Place the nail leg (M) on the two sides of panel 2 and panel 3.
4
8
17
7
6
M
3
5

12 | P a g e
www.Hodedah.com
Step 5
*Fix panel 1 onto panel 2 and 3 and align properly by inserting 5 dowels on
panel 2, 3 & 4 onto the non-thru holes of panel 1.
*Gently tap panel 1 on panels 2, 3 & 4 dowels.
*Fasten 4 screws (C) on panel 1 to attach panels 2 & 3.
1
3
24

13 | P a g e
www.Hodedah.com
Step 6
*Fix approximately 30 pieces of nails (F) into Panel 16 using a hammer.
*Cover all the screws (C)' head with sticker (L) provided by stick up onto
hole of screw (C)' heads one by one.
16
16
F

14 | P a g e
www.Hodedah.com
Step 7
*Insert 4 (J) hinges onto panel 9's predrilled holes, then fasten screws (D)
into hinges (J).
9
2. Fasten 2 screws (E)
from inner side of door
panel 9 into the handle
(H) holes.
1. Panels 9 doors can
be used for both right
side and left side.
9

15 | P a g e
www.Hodedah.com
Step 8
Assembly Of Drawer: 2 Drawers
*Insert the minifix (B)
10
X2
*Insert Panel 14 into the
drawer and align
properly. (As shown)
*Insert Panels 11,12 and 15
on to panel 10 by slightly
hammering the dowels.
12
15
11
14
10
X2 *Insert the minifix (B)(nuts)
with the cross arrow mark
facing upwards and aim to
panel 11,12 and 15 's top
thru holes.(As shown)

16 | P a g e
www.Hodedah.com
12
15
11
X2
*Place panel 13 on each side of panel 11 and 12 as shown.
*Then, tighten screws (C) to panel 11's upper thru holes to fix them onto panel 13.
*Next tighten screws (C) to panel 12's upper thru holes to fix up to the panel 13.
*Tighten screws (C) to panel 13's upper thru holes to fix up to the panel 15.
*Flip the drawer over.
*Tighten 2 screw (E) from inner
side of panel 10 into the handle (H)
holes.
10
X2

17 | P a g e
www.Hodedah.com
Place the “L” shaped drawer slide (I) with the small white roller facing
outwards and should be in parallel with drawer front panel 10. Then tighten
3 screws (D) on each drawer slide (I).
I
D
I
D
D
I
X2
I
11
"L" shaped - right
of the drawer
slide stick to the
end of drawer
front panel 10.
10
"L" shaped - left
of the drawer
slide stick to
the end of
drawer front
panel 10.
I
12

18 | P a g e
www.Hodedah.com
Step 9
Almost there
*Place hanger (G) onto panel 2 and 3's V-bracket.
K
You can align and
adjust the door
panels by tightening
and loosening the
screw.
Fasten 4 screw (D)
on hinges (J).
9
9

19 | P a g e
www.Hodedah.com
Step 10
*Take all drawers, and slide them (the white rollers at drawer slide at both
side of drawers are to go into the track of the slide at each side panel.)All
the way gently, one drawer by one drawer starting from bottom to the top
accordingly.
10
10

20 | P a g e
www.Hodedah.com