Hodedah HIBT 70 User manual

1
Hodedah
www.hodedah.com
support @hodedah.com
HIBT 70 - FB & SR
L42 28'' X D84 78'' X H35''
(M/S - 39" X 75")
HIBT70-FB & SR
HIBT70-HB

PART & HARDWARE LIST
2
CAP
Hodedah
www.hodedah.com
support @hodedah.com
APLASTIC DOWEL M8 X 25MM 22
B
CSK CAP M6 X 40MM 6
36
14
H1 H2
C
D
CB SCREW M4 X 35MM
6+6
MINIFIX 5654 2+2
1
ALLEN KEY
I
PLASTIC PINJ
K1
L
4
1
2
5
6
3
8-A
10
10
9
11
8-C
8-B
7
3
7
7
7
12
12
12
L1
L2
CB SCREW M3.5 X 12MM
JCBC BOLT M6 X 50MM 12
1
ALLEN KEY
12
BARREL NUT
HANDLE IP994 (96MM) - PVC 3
P/H SCREW M4 X 40MM 6
DRAWER SLIDE 16"
CB SCREW M4 X 25MM
18
6
CB SCREW M3.5 X 16MM
46
16
D
E
F
G
H N
M
K2

3
- This product contains small components, please ensure that they are
kept away from small children.
- THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE
REFERENCE.
STOP
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, email our customer
service. We will gladly ship your replacement parts
FREE of charge.
email us at
[email protected]
For prompt, reliable service; please have your
assembly manual ready.
Need Parts or Assistance?
Hodedah
www.hodedah.com
support @hodedah.com

4
Thank you for purchasing from Hodedah
To learn more about hodedah and our products visit
www.hodedah.com
READ BEFORE BEGINNING ASSEMBLY
- Read each step carefully. It is very important that each step of instruction is performed in the
correct order. If these steps are not followed in sequence, assembly difficulties will occur.
- Make sure all parts are included. Most parts are labeled or stamped on the raw edge.
- Work in spacious area, preferably on a carpet, near the place the unit will be used.
- Do not use power tools to assemble your furniture. Power tools may strip or damage the parts.
HELPFUL HINTS
- Call us if you need assistance.
- Move your new furniture carefully, with two people lift and carry the unit to it's new location.
- Never push, drag or pull your furniture (especially on carpet).
Warranty Information
Hodedah warrants this product to be free from defects in material and workmanship agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is
solely limited to be repair or replacement of defective parts and no assembly labor is included.
This warranty does not apply to any product which has been improperly assembled, subjected to
misuse or abuse or which has been altered or repaired in any way.
To obtain warranty, purchaser must present original bill of sale. Components repaired or
replaced warranted through the remainder of the original warranty period only. The defective
components will be repaired or replaced without charge, subject to the terms and conditions
described above.
For help with assembly, identifying parts, product information or to
order parts, please contact us :
Call us at :
718-456-0505
Monday - Friday
9:00am - 5:00pm
Visit our website :
www.hodedah.com
Hodedah
www.hodedah.com
support @hodedah.com

J
STEP 1
Hodedah
www.hodedah.com
support @hodedah.com
A
5
PLASTIC DOWEL M8 X 25MM 22
PLASTIC PINPLASTIC PIN
4
1
2
2
5
6
6
1
2
4
3
3
A
- Insert 22 x Plastic dowel (A) into Panels (1), (2)x2, (4), (5) & (6) using a plastic hammer.
- Knock 16 x Plastic pin (J) into panels (1), (2)x2, (3)x2, (4) & (6) base by using a plastic hammer.
2
J16

4
1
6
5
G
H2
5
STEP 2
Hodedah
www.hodedah.com
support @hodedah.com
6
- Insert 12 x Barrel nut (G) into inside of Panels (1), (4), (5) & (6) inside.
- Insert 2 x Minifix (H2) into inside of Panels (5) & (6) by using a Philip head screwdriver.
H2
12
G BARREL NUT
2
MINIFIX 5654
H2
INSIDE VIEW
INSIDE VIEW

33
B
L1
22
RIGHT VIEW LEFT VIEW RIGHT VIEW LEFT VIEW
LEFT VIEW RIGHT VIEW
8A
- Attach 4 x Drawer slide 16" (L1) into Panel (2) left & right side. Insert 12 x CB Screw M3.5 x 12mm (B) &
tighten with Philip head screwdriver.
- Attach 2 x Drawer slide 16" (L1) into Panel (3) left & right side. Insert 6 x CB Screw M3.5 x 12mm (B) &
tighten with Philip head screwdriver.
- Insert 2 x CB Screw M4 x 25mm (N) into Panel (8A) back & tighten with Philip Head Screwdriver.
Do the same step for Panel (8B) & (8C).
STEP 3
Hodedah
www.hodedah.com
support @hodedah.com
B
7
CB SCREW M3.5 X 12MM 18 6 N
DRAWER SLIDE 16" 6
L1
8B 8C
L1
CB SCREW M4 X 25MM
N

10
910
8A 8B
8C
C
11 11 B
STEP 4
Hodedah
www.hodedah.com
support @hodedah.com
B
8
CB SCREW M3.5 X 12MM 18
DRAWER SLIDE 16"24
P/H SCREW M4 X 40MM
HANDLE IP994 (96MM) - PVC 3
6
6
MCB SCREW M3.5 X 16MM
CCB SCREW M4 X 35MM
K1
L2
K2 6
L2
L2
K2
K1
M
11 10
- Attach 2 x Panel (10) into Panel (8A). After that attach 1 x Panel (9) into both Panel (10) with
8 x CB Screw M4 x 35mm (C). Tighten using Phillips head screwdriver. Repeat for the next drawer.
- Fix 3 x Handle (K1) to Panel (8A), (8B) & (8C) front. Insert 6 x P/H Screw M4 x 40mm (K2) & tigthen with
Phillips head screwdriver.
- Slot 1 x Panel (11) into Panel (10) groove & insert 6 x CB Screw M3.5 x 16mm (M). Tighten with Phillips
head screwdriver. Do the same step for the next 2 drawer boxs.
- Fix 6 x Drawer slide 16" (L2) into Panel (10) using 18 x CB Screw M3.5 x 12mm (C) & tighten with
Philip head screwdriver.

C
12
1
2
FD
2
3
5
4
6
FE
I1
STEP 5
Hodedah
www.hodedah.com
support @hodedah.com
C
9
6
CAP4
ALLEN KEY
6
6
D
CB SCREW M4 X 35MM 1
- Attach 3 x Panel (12) into drawer base using 6 x CB Screw M4 x 35mm (C). Tighten using Phillips head
screwdriver.
- Attach 2 x Panel (2) into Panel (1) using 4 x CSK CAP M6 x 40mm (D). Fully tighten with Allen key (F).
- Attach Panel (5) & (6) into Panel (2).
- Attach Panel (3) into panel Panel (1), (4), (5) & (6) using 6 x Jcbc Bolt M6 x 50mm (E). Fully tighten with
Allen key (F) & insert 6 x Cap (I).
CSK CAP M6 X 40MM
EJCBC BOLT M6 X 50MM
I
F
2
2

F
5
4
61
H1
F
E
I
DFI
LEFT VIEW
STEP 6
Hodedah
www.hodedah.com
support @hodedah.com
10
CAP
2
ALLEN KEY
68
D
1
- Insert 2 x Minifix 5654 (H1) into Panel (2) & (5) using Allen key (F).
- Insert 2 x CSK Cap M6 x 40mm (D) into Panel (6) using Allen key (F) & insert 2 x Cap (I).
- Attach Panel (3) into Panel (4), (5) & (6) using 6 x JCBC Bolt M6 x 50mm (E). Fully tighten with
Allen key (F) & insert 6 x Cap (I).
CSK CAP M6 X 40MM
EJCBC BOLT M6 X 50MM I
F
2
2
H1 MINIFIX 5654 2
6
5
2
1
3
2
43
RIGHT VIEW
H1

STEP 7
11
Hodedah
www.hodedah.com
support @hodedah.com
Job Complete !
In the interest of our environment please dispose of all packaging throughtfully.
- Place 4 x Panel (7) into Panel (4) & (5). Insert 16 x CB Screw M4 x 35mm (C) & tighten with Philip
head screw driver.
- Slide the drawer box into the drawer slide at the Panel (2) & (3).
C16CB SCREW M4 X 35MM
7
7
7
7
8-A
8-B
8-C
C