Hodedah HI70DR-A User manual

1 | P a g e
www.Hodedah.com
Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
ITEM # HI70DR-A
7 DRAWER CHEST
FRONT VIEW BACK VIEW
Product Dimensions: Height48.3” x Width 31.5” x Depth 17.75”
Weight Capacity: Large Drawer 20 lbs. | Small Drawer 15 lbs.
2 people
90mins
1 YR LTD
1 Box

2 | P a g e
www.Hodedah.com
Questions, need parts, we are here to help!
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
DO NOT RETURN PRODUCT TO THE STORE
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
______________________________________________
WARRANTY
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
WARNING
•This product contains small parts, keep away from children.
•This product contains plastic bags, keep away from children.
•Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
•Never allow children to climb or hang on drawers, shelves and doors.
•Never open more than one drawer at a time.
•The use of tip-over restraints may reduce but not eliminate the risk of tip-over.
Phone
Mon –Fri | 9:30 am to 5pm EST
1 - 855 –HODEDAH
1 –855 –463 -3324
Email
Send us an email
[email protected]
Website
Visit our website to open a case
www.Hodedah.com

3 | P a g e
www.Hodedah.com
Let’s get started…
Helpful hints, read before beginning assembly
•Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
•Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
•Work in a spacious level area, preferably carpet, near the place the unit will be used.
•DO NO USE power tools to assemble your furniture, it will strip and damage parts.
•Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Assembly Tools Required (not supplied)
Hammer Phillips Screwdriver Tape Measure No Power Tools Needed
____________________________________________________________________________________
Product Care and Maintenance
•Wipe clean with dry soft cloth, never use chemicals or cleaning products they will
damage the finish.
•Avoid placing your furniture in direct sunlight, as sunlight causes fading.
•Never push, drag or pull your furniture, to move to a new location carefully with two or
more people carry the unit to its new location.
•Avoid extreme changes in temperature by arranging furniture away from radiators, heat
and air vents and air conditioning units.

4 | P a g e
www.Hodedah.com
Hardware List
A
PVC Dowel
QTY
54Pcs
B
Minifix
QTY
25Sets
C
Screw M4x45mm
QTY
53Pcs
D
Screw M3.5x16mm
54Pcs
E
Screw M3.5x21mm
14Pcs
F
Sticker
32Pcs
G
Handle (96mm)
7Pcs
H
Drawer Slide –A
(300mm)
14Pcs
I
Nail
40Pcs
J
Lock
2Sets
K
Leg
4Pcs
Important
1. Before you throw the package, please use the Check Box to identify the parts and hardware to
ensure that you have everything you need.
2. Check and measure the bolts before applying them to parts.
3. Do not completely tighten all hardware until the entire assembly is complete, unless indicated
otherwise.

5 | P a g e
www.Hodedah.com
Parts List
1 Left Side Panel
1200x430x15mm
QTY
1pc
2 Right Side Panel
1200x430x15mm
QTY
1pc
3 Divider Panel
430x180x15mm
QTY
1pc
4 Strengthening
Panel - Back LVL
758x65x15mm
1pc
5 Strengthening
Panel –Front LVL
758x65x15mm
1pc
6 Back
Strengthening Panel
758x70x15mm
1pc
7Front
Strengthening Panel
758x70x15mm
4pc
8 Kick Panel
758x95x15mm
2Pcs
9 Top Panel
800x450x30mm
1pc
10 Back Panel
1170x393x2.5mm
2Pcs
11 Drawer Front
Panel –Big Drawer
778x180x15mm
5Pcs
12 Drawer -
Left Side Panel
350x116x15mm
7Pcs
13 Drawer End
Panel –Big Drawer
701x116x15mm
5Pcs
14 Drawer –
Right Side Panel
350x116x15mm
7Pcs
15 Drawer Base
Supporting Panel
335x50x15mm
5Pcs
16 Drawer Base
Panel –Big Drawer
710x344x2.5mm
5Pcs
17 Left Drawer
Front Panel –Small
Drawer
386x180x15mm
1Pc
18 Right Drawer
Front Panel –Small
Drawer
386x180x15mm
1Pc

6 | P a g e
www.Hodedah.com
19 Drawer Base
Panel –Small Drawer
323x344x2.5mm
2Pcs
20 Drawer End
Panel –Small Drawer
314x116x15mm
2Pcs
The Breakdown…
11
12
14
13
16 15
1
9
2
10
10
8
8
67
5
4
319 12
20 14
17 19
18
14
20
12
11
7
7
7

7 | P a g e
www.Hodedah.com
Step 1
Insert PVC dowel (A) to Panel 1,2,3,4,5,6,7,8,12 and 14's non-thru holes as shown,
using hammer to gently tap them in.
Non-thru holes (are small indents in the wood that show you were the screws should
be.)

8 | P a g e
www.Hodedah.com
Step 2
Place the drawer slide (H) at the
predrilled holes on the panel 1 and 2
as shown . Then tighten the drawer
slide (H) with 3 screws (D).
H
Insert (K) Nail Protection onto
the bottom edge of panel 1 and
2,slightly tapping them in with a
hammer
Insert the minifix (B) nut with the cross arrow
mark facing upwards,you will be able to see the
opening of the Nut (B) thru the top edges of
panels 1 and 2.
1
Place the drawer slide (H) at the
predrilled holes on the panel 1 and 2
as shown . Then tighten the drawer
slide (H) with 3 screws (D).
Repeat the same
as above

9 | P a g e
www.Hodedah.com
Step 3
Insert the minifix (B) (nuts) with the cross
arrow mark facing up ward and aim to panel
3 's top thru holes.(AS shown)
Place the drawer slide (H) onto the 3 holes
area shown at right view of panel 3. then
tighten it with 3 screws (D).
RIGHT VIEW
H
D
Place the drawer slide (H) onto the 3
holes area shown at left view of
panel 3. then tighten it with 3 screws
(D).
LEFT VIEW

10 | P a g e
www.Hodedah.com
Step 4
*Place and fix Panel 4, 5, 6, 7 and 8 onto Panel 1 by inserting the (Left) dowels onto the
non-thru holes at Panel 1 by slightly tapping them in with hammer.
*Inset and Fasten screw (C) (Using predrilled holes on Panel 1) into the Panel 4,5,6,7
and 8 by using screwdriver.
15
4
7
7
7
7

11 | P a g e
www.Hodedah.com
Step 5
*Place and fix Panel 3 onto panel 4 and 5 by inserting the dowels onto the non-thru
holes at Panel 3.
*Fasten screw (C) from under the Panel 4 and 5 using predrilled holes and tighten it into
Panel 3.
7
6
8
8
2
5
4
13
7
7
7
*Place and fix Panel 4,5,6,7 and 8 onto Panel 2 by inserting the (Right) dowels onto
the non-thru holes at Panel 2, then slightly hammer it in from outside of Panel 2.
*Fasten screw (C) from the outside of Panel 2 by using the predrilled holes to
attach Panel 4,5,6,7 and 8.

12 | P a g e
www.Hodedah.com
Step 6
*First prepare panel 9.
*Place minifix (B) Long piece onto the holes of Panel 9. (You will use 6 pcs)
*Then place lock stopper (J) onto the bottom of Panel 9, using screw (D).
*Fix Panel 9 onto Panel 1, 2 and 3 align properly by inserting the 6 dowels of Panel 1
and 2 onto the non-thru holes of Panel 9. (Slightly hammer it in)
*Pushing and light tapping of Panel 9 to have Panel 1, Panel 2, Panel 3, and Panel 9 fix
tightly.
*Tighten minifix (B) clockwise to lock minifix up by going under Panel 9 and tighten it
upon both sides and middle pieces (Panel1, 2, and 3)
B
6
8
8
5
9
3
1
2
4
DJ
7
7
7
7

13 | P a g e
www.Hodedah.com
Step 7
*Fix 40 x Nails (I) into Panel 10 using a Hammer
*Cover all the screws (C)' head with sticker (F) provided by stick up onto hole of screw
(C)' heads one by one for all the screw (C)
10
10

14 | P a g e
www.Hodedah.com
Step 8
Assembly Of Big Drawer : 5 Drawers
11
*Insert the mini fix (B)
*Insert the mini fix (B)(nuts)
with the cross arrow mark
facing upward and aim to
panel 12,14 and 15 's top
thru holes.(As shown)
*Insert Panel 16 into the
drawer and align
properly. (As shown)
*Insert Panels 12,14 and 15
on to panel 11 by hammering
the dowels slightly

15 | P a g e
www.Hodedah.com
*Place panel 13 on each side of panel 12 and 14 as shown.
*Then, tighten screw (C) to panel 14 's upper thru holes to fix them onto panel 13.
*Next tighten screw (C) to panel 12 's upper thru holes to fix up to the panel 13.
*Tighten screw (C) to panel 13 upper thru holes to fix up to the panel 15.
*Cover all screw (E)' head
with sticker provided by
stick up onto the hole of
screw (E)' head.
*Flip the drawer over.
*Tighten 2 screw (E) from
inner side of panel 11 into
the handle (G) holes.

16 | P a g e
www.Hodedah.com
Step 8
Assembly Of Small Drawer : 2 Drawers
*Insert the mini fix (B)
18
14 12
16
18
*Insert the mini fix (B)(nuts) with
the cross arrow mark facing
upward and aim to panel 12 and
14 's top thru holes.(As shown)
*Slide in panel 16 into panel 12
and 14,slightly hammer panel 12
and 14 into panels 17 and 18.
C
*Place panel 20 on each side of
panel 12 and 14 as shown.
*Then, tighten screw (C) to
panel 12 's upper thru holes to
fix them onto panel 20.
*Next tighten screw (C) to panel
14 's upper thru holes to fix up
to the panel 20.

17 | P a g e
www.Hodedah.com
*Cover all screw (E)'head with
sticker (F) provided by stick up onto
the hole of screw (E)' head.
*Flip the drawer over.
*Tighten 2 screw (E) from
inner side of panel 17 and
18 into the handle (G)
holes.
18
17
J
*Flip the drawer over.
*Tighten 4 screw (D) from inner side
of panel 17 and 18 into the Lock (J)
holes.
18

18 | P a g e
www.Hodedah.com
Step 9
*Take all drawers, and slide them (the white rollers at drawer slide at both side of
drawers are to go into the track of the slide at each side panel.)All the way gently,
one drawer by one drawer starting from bottom one.
9
2
18
17
11
11
11
11
11

19 | P a g e
www.Hodedah.com

20 | P a g e
www.Hodedah.com
Job Complete…
9
2
18
17
11
11
11
11
11
Enjoy &Thank you for purchasing from Hodedah!