Hodedah HI K78 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT INFORMATION ABOUT ASSEMBLY AND
SAFETY. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
1
HIK 78 (KITCHEN TROLLEY)
FRONT VIEW REAR VIEW
~ Before assembly, please read the instructions ~
~ Keep these instructions for future reference ~ ~ Follow these steps to assemble the Kitchen Trolley ~

2
1SMALL SIDE (L/R) 2SIDE PANEL (L)
3BOX BOTTOM PANEL 4BOX SIDE (L/R)
5SIDE PANEL (R) 6MIDDLE SUPPORT
120 x 120 x 15 800 x 394 x 15
360 x 188 x 15 190 x 140 x 15
800 x 394 x 15 768 x 76 x 15
X2
x2
I) Main Unit : II) Door & Drawer :
The parts of the product are packed in one box.
These are inner box(es) or package(s) that included components
and accessories required to complete the assembly.
1
2
34
5
6
7
8
9
10 10
11
12
12
13
14
15 16
7TOP PANEL
900 x 396 x 30 8BOTTOM PANEL 802 x 396 x 15 9SHELF PANEL 768 x 350 x 15 10 BACK PANEL 840 x 397 x 2.5
DRAWER HEAD
760 x 140 x 15
11 DRAWER SIDE (L/R)
350 x 90 x 15
12 DRAWER FRONT & BACK
712 x 60 x 15
13
DRAWER PANEL
722 x 350 x 2.5
14 DOOR PANEL (L)
629 x 378 x 15
15 DOOR PANEL (R)
629 x 378 x 15
16

3
Q
P
O
NM
GH I J K L
FED
C
BA
R
S

4

5

6
1
C
SMALL SIDE (L/R) 3BOX BOTTOM PANEL 4BOX SIDE (L/R)
2SIDE PANEL (L) 5SIDE PANEL (R) 6MIDDLE SUPPORT
7TOP PANEL
BOTTOM VIEW
Tighten minifix
(A2) to panel (7).
K
R1
2SIDE PANEL (L)
R VIEW 5SIDE PANEL (R) L VIEW
Place the drawer slide on
to 3 hole area shown at
Left Down side panel (2).
Then tighten it with 3
screws (k).
Place the drawer slide on
to 3 hole area shown at
Left Down side panel (5).
Then tighten it with 3
screws (k).
15 DOOR PANEL (L) 16 DOOR PANEL (R)
Insert door spring support
(H) to door panel (15) and
(16).

7
15 DOOR PANEL (L) DOOR PANEL (R) 16
Tighten 2 Screws (O) from
Door Panel (15 & 16) into
the handle (M) hole.
MIDDLE SUPPORT
BOTTOM VIEW
6
Insert magnet (F2) onto panel (6) 's non-thru holes
as shown, make sure the magnets, iron side facing
frontward to edging direction.
2SIDE PANEL (L)
R VIEW 5SIDE PANEL (R) L VIEW
Insert 2 Shelf Support (I) on Panel 2 & 5.
15 DOOR PANEL (L)
R VIEW 16 DOOR PANEL (R) L VIEW
Fix and tighten metal piece (F1) with screw (G) at
door panel (15 & 16) as shown.

8
COMPLETED
- Place 2 panel 12 on each side of panel as shown
- Then tighten screw (J) to panel 13 lower thru
holes to fix them onto panel 12
- Holes to fix up to the panel 11
- Filp drawer with bottom side up, place panel 12 onto the
drawer and align properly. Then slot in the back panel 14
into the side panel 12, then nail the nails provided with
hammer on the drawer back panel 14 up side.
The gap between 2 nails is about 175mm.
- After that, place a drawer slide R2 with the small white
roller facing outward and with other and tip touching panel
12 onto each bottom side (angle) edge. Then tighten 3
screws (K) on each drawer slide R2 (as shown).
- Tighten 2 screw (J) from inner side of panel 11 into the
handle (M) holes.

9
S
Put in the chrome pipe (S) to panel (4) then fix onto panel (3) by
inserting dowels (C) onto non-thru at panel (3) use allen key (L)
to tighten screws (D) from the thru-holes of panel (4) after that
insert CSK CAP (E).
D
L
E

10
Fix Panel (3,4) onto panel (5) by inserting dowels (C) onto
non-thru at panel (3,4) use allen key (L) to tighten screws (D)
from the thru-holes of panel (5) after that insert CSK CAP (E).
D
L
E