Hodedah HI425WHITE User manual

Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
HODEDAH ®
ITEM # HI425-G
NIGHT TABLE
2 peoples
30 mins
1 YR LTD
1 Box
www.Hodedah.com 1| Page
Product Dimensions: Height 29.52" x Width 47.24" x Depth 23.62"
Weight Capacity Per Drawer 15lbs
FRONT VIEW BACK VIEW

HODEDAH ®
www.Hodedah.com 2| Page
DO NOT RETURN PRODUCT TO THE STORE
Phone WebsiteEmail
Questions, need parts, we are here to help!
WARRANTY
WARNING
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
Mon - Fri | 9:30 am to 5pm EST Send us an email
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
Visit our website to open a case
1 - 855 - HODEDAH
1 - 855 - 463 -3324
[email protected] www.Hodedah.com
·This product contains small parts, keep away from children.
·This product contains plastic bags, keep away from children.
·Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
·Never allow children to climb or hang on drawers, shelves and doors.
·Never open more than one drawer at a time.
·The use of tip-over restraints may reduce but not eliminate the risk of tip-over.

HODEDAH ®
www.Hodedah.com 3| Page
Product Care and Maintenance
Let's get started…
·Never open more than one drawer at a time.
·The use of tip-over restranits may reduce but not eliminate the risk of tip-over.
·Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
·Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
·Work in a spacious level area, preferably carpet, near the place the unit will be used.
·DO NO USE power tools to assemble your furniture, it will strip and damage parts.
·Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Helpful hints, read before beginning assembly
Assembly Tools Required (not supplied)
·Wipe clean with dry soft cloth, never use chemicals or cleaning products they will
damage the finish.
·Avoid placing your furniture in direct sunlight, as sunlight causes fading.
·Never push, drag or pull your furniture, to move to a new location carefully with
two or more people carry the unit to its new location.
·Avoid extreme changes in temperature by arranging furniture away from radiators,
heat and air vents and air conditioning units.
Hammer Phillips Screwdriver No Power Tools NeededTape Measure

HODEDAH ®
www.Hodedah.com 4| Page
Hardware List
1QTY 2QTY 3QTY
QTY 5QTY 6QTY
Pvc Dowel
7QTY 9QTY
Nail
QTY
Allen Key
10 Pcs
QTY
4
25 Pcs
8 Pcs
Screw M6 x 40mm
Screw M4 x 32mm Screw M6.2 x 10mm
*For # 12 Drawer Slides
Pvc Cap
10 Sets
Pvc Cap
Mini Fix
10 Pcs
11 14
2 Pcs
8 Pcs
Screw M3.5 x 14mm
*For # 13 Drawer Slides
16 Pcs
M3x16mm Screw
1 Pc15 Pcs
10 QTY
Backply Stopper
2 Pcs
10 Pcs

HODEDAH ®
www.Hodedah.com 5| Page
Accessories
QTY
Handle 2 Pcs
4 Pcs
12
13
Drawer Slide - A
*Fix On Side Panels
QTY
2 Sets
QTY
2 Sets
*Fix On Side Panels J K
Drawer Slide - B
A F
Screw M4 X 20mm
* Fix On Side Panels Ⓐ
* Fix On Side Panels Ⓕ
* Fix On Drawer Side Panels Ⓙ
* Fix On Drawer Side Panels Ⓚ
Important
1. Before you throw the package, please use the
Check Box to identify the parts and hardware to
ensure that you have everything you need.
2. Check and measure the bolts before applying them
to parts.
3. Do not completely tighten all hardware until the
entire assembly is complete, unless indicated
otherwise.
8

HODEDAH ®
www.Hodedah.com 6| Page
AQTY
1 Pc
BQTY CQTY
DQTY EQTY FQTY
GQTY HQTY IQTY
Parts List
JQTY KQTY QTY L
Drawer Front Panel
334 x 140 x 15mm
Right Drawer Side Panels
292 x 102 x 15mm
Top Panel
1200 x 600 x 15mm
Stand Panel
292 x 330 x 15mm
Left Side Panel
735 x 394 x 15mm
Left Drawer Side Panels
292 x 102 x 15mm
Back Panel
976 x 292 x 15mm
Right Side Panel
735 x 394 x 15mm
Back Strengthening Panel
976 x 90 x 15mm
Drawer End Panels
287 x 100 x 15mm
1 Pc 1 Pc
1 Pc
1 Pc 1 Pc
2 Pcs
1 Pc
Front Strengthening Panel
342 x 76 x 15mm
1 Pc
2 Pcs
2 Pcs
Drawer Base Panels
315 x 296 x 3mm
2 Pcs

HODEDAH ®
www.Hodedah.com
The Breakdown
HODEDAH ®
www.Hodedah.com 7| Page
The Breakdown
x2

HODEDAH ®
www.Hodedah.com 8| Page
Step 1
9Mini Fix
6 Pcs.
9Mini Fix
6 Pcs.
5
Screw M6.2 x 10mm
8 Pcs.
A. Place the drawer slide A ⑫
onto the 2 holes area shown at
stand panel Dand F. Then
tighten it with 2 screws ⑤
and 1 screw ③.
B. Insert the mini fix
⑨(nuts) with the
cross arrow mark
facing upward and
aim to panel
A,C,D & F 's
top thru holes. (As
shown)
C. Insert the PVC dowels ①to panel A,B,C,D,E and
F ’s non-thru holes as shown, using hammer to tap them in.
D. Insert, push down and tighten mini fix
screw ⑨, to the hole as shown (Panel G)
PANEL
G
PANEL A
PANEL
C
PANEL
B
PANEL
E
PANEL
D
PANEL
F
1Pvc Dowel
17 Pcs.
3
Screw M3.5 x 14mm
4 Pcs.

HODEDAH ®
www.Hodedah.com 9| Page
Step 2
6
Screw M6 x 40mm
2 Pcs.
Fix Panel Eonto Panels Fby inserting the dowels onto the non-thru
holes at Panel F.
Next, fix Panel Donto panel Eby inserting the dowels onto the
non-thru holes at Panel D.
Use allen key ⑭to tighten 2 screw ⑥from the thru-holes of panel D
and Fto non-thru hole of panels Eas shown.

HODEDAH ®
www.Hodedah.com 10| Page
Step 3
6
Screw M6 x 40mm
8 Pcs.
Fix Panel B, C & E onto Panels Fby inserting the dowels onto the
non-thru holes at Panel F.
Next, fix Panel Aonto panel B & C by inserting the dowels onto the
non-thru holes at Panel A.
Use allen key ⑭to tighten 8 screws ⑥from the thru-holes of panel
A,Cand Fto non-thru hole of panels B & C as shown.

HODEDAH ®
www.Hodedah.com 11| Page
Step 4
-Fix panel Gonto panels A,C,D & F and align properly by inserting the
4 dowels of panels A & F onto the non thru holes of panel G.
-Pushing and light tapping of panel Gto have panel A, G & F fix tightly.
-Then, tighten mini fix ⑨clockwise to
lock the mini fix up for tightening panel
Gup. Cover 4 mini fix caps provided by
pushing the cover 's stem onto the hole
of mini fix nut on upper side of panel
A,C,D and F.

HODEDAH ®
www.Hodedah.com 12| Page
9Mini Fix
4 Pcs.
9Mini Fix
4 Pcs.
1Pvc Dowel
8 Pcs.
Step 5
B. Insert the PVC dowels ①to panel Iand J ’s non-thru holes as shown, using
hammer to tap them in.
A. Insert the mini fix ⑨(nuts) with the cross arrow mark facing upward and aim to
panel I & J 's top thru holes. (As shown)
C. Insert, push down and tighten mini fix screw ⑨, to the hole as shown (Panel H)
x2
PANEL
I
x2
PANEL
J
x2
PANEL
H

HODEDAH ®
www.Hodedah.com 13| Page
Assembly Of Drawers
3
Screw M3.5 x 14mm
12 Pcs. 4
Screw M4 x 32mm
8 Pcs. 8Handle
2 Pcs. 8
Screw M4 X 20mm
4 Pcs.
(1)
11 Nail
14 Pcs.
(2)
2
M3x16mm Screw
2 Pcs. 10
Backply Stopper
2 Pcs.
x2
-Place panel Iand J on each side of panel H
with Panel I and J 's PVC dowel insert to panel
H 's non-thru hole and Panel H 's mini fix screws
insert into Panel I and J 's thru as shown.
Then tighten mini fix on panel I and J clockwise to
lock mini fix up.
-Next tighten screw ④to panel I and J 's upper
thru holes to fix up to the panel K.
-Flip drawer with
bottom side up, place
panel Lonto the
drawer and align
properly. Then nail the
nails provided with
hammer on the border
of panel Las
shown.The gap
between 2 nails is
about 100mm.
-After that, place a
drawer slide B ⑬with
the small white roller
facing outward and
with other end tip
touching panel Honto
each bottom side
(angle) edge of panel
Iand J. Then tighten
3 screws ③on each
drawer slide B ⑬
(as shown).
Put the backply stopper ⑩onto
panel Lwith the shorter part
touching panel H, then tighten
it with screw ②.
-Flip the drawer over.
-Tighten 2 screw ⑧from inner side of panel Hinto the handle ⑧holes.
(3)

HODEDAH ®
www.Hodedah.com 14| Page
Step 6
Take drawers and slide them (the white rollers at drawer slide at both side of
drawers are to go into the track of the slides at each side panel.) all the way
gently, one drawer by one drawer starting from bottom one.
Screw Cap

HODEDAH ®
www.Hodedah.com
Job Complete
15| Page
In the interest of our environment please dispose of all packaging thoughtfully.
Enjoy & Thank you for purchasing from Hodedah!