Hodedah HI917N-G User manual

Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
HODEDAH ®
ITEM # HI917N-G
NIGHT TABLE
1 people
30 mins
1 YR LTD
1 Box
www.Hodedah.com 1| Page
Product Dimensions: Height 17" x Width 15.62" x Depth 19"
Weight Capacity Per Drawer 15lbs
Weight Capacity Per Shelf 15lbs
FRONT VIEW BACK VIEW

HODEDAH ®
www.Hodedah.com 2| Page
DO NOT RETURN PRODUCT TO THE STORE
Phone WebsiteEmail
Questions, need parts, we are here to help!
WARRANTY
WARNING
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
Mon - Fri | 9:30 am to 5pm EST Send us an email
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
Visit our website to open a case
1 - 855 - HODEDAH
1 - 855 - 463 -3324
[email protected] www.Hodedah.com
·This product contains small parts, keep away from children.
·This product contains plastic bags, keep away from children.
·Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
·Never allow children to climb or hang on drawers, shelves and doors.
·Never open more than one drawer at a time.
·The use of tip-over restraints may reduce but not eliminate the risk of tip-over.

HODEDAH ®
www.Hodedah.com 3| Page
Product Care and Maintenance
Let's get started…
·Never open more than one drawer at a time.
·The use of tip-over restranits may reduce but not eliminate the risk of tip-over.
·Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
·Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
·Work in a spacious level area, preferably carpet, near the place the unit will be used.
·DO NO USE power tools to assemble your furniture, it will strip and damage parts.
·Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Helpful hints, read before beginning assembly
Assembly Tools Required (not supplied)
·Wipe clean with dry soft cloth, never use chemicals or cleaning products they will
damage the finish.
·Avoid placing your furniture in direct sunlight, as sunlight causes fading.
·Never push, drag or pull your furniture, to move to a new location carefully with
two or more people carry the unit to its new location.
·Avoid extreme changes in temperature by arranging furniture away from radiators,
heat and air vents and air conditioning units.
Hammer Phillips Screwdriver No Power Tools NeededTape Measure

HODEDAH ®
www.Hodedah.com 4| Page
Hardware List
1QTY 2QTY 3QTY
QTY 5QTY 6QTY
Pvc Dowel
7QTY 9QTY
Nail
QTY
Allen Key
6 Pcs
15
QTY QTY
4
18 Pcs
8 Pcs
Screw M6 x 40mm
Screw M4 x 32mm
4 Pcs
Screw M6.2 x 10mm
*For # 13 Drawer Slides
Pvc Cap
8 Sets
Pvc Cap
Mini Fix
8 Pcs
11 12
2 Pcs
8 Pcs
Nail Leg
Screw M3.5 x 14mm
*For # 14 Drawer Slides
12 Pcs
M3x16mm Screw
6 Pcs
1 Pc30 Pcs
10 QTY
Backply Stopper
2 Pcs
16
(separate from
hardware pack)
Anti-Tip Kit
QTY
1 PK

HODEDAH ®
www.Hodedah.com 5| Page
Accessories
8QTY
Handle 2 Pcs
4 Pcs
13
14
Drawer Slide - A
*Fix On Side Panels
QTY
2 Sets
QTY
2 Sets
*Fix On Side Panels J K
Drawer Slide - B
A F
Screw M4 X 20mm
* Fix On Side Panels Ⓐ
* Fix On Side Panels Ⓕ
* Fix On Drawer Side Panels Ⓙ
* Fix On Drawer Side Panels Ⓚ
Important
1. Before you throw the package, please use the
Check Box to identify the parts and hardware to
ensure that you have everything you need.
2. Check and measure the bolts before applying them
to parts.
3. Do not completely tighten all hardware until the
entire assembly is complete, unless indicated
otherwise.

HODEDAH ®
www.Hodedah.com 6| Page
AQTY
1 Pc
BQTY CQTY
DQTY EQTY FQTY
GQTY HQTY IQTY
Parts List
JQTY KQTY QTY L
Drawer Front Panel
386 x 140 x 15mm
Front Kick Panel
394 x 78 x 15mm
Right Drawer Side Panels
338 x 76 x 15mm
Top Panel
432 x 394 x 30mm
Back Strengthening Panel
394 x 78 x 15mm
Left Side Panel
448 x 381 x 15mm
Left Drawer Side Panels
338 x 76 x 15mm
Back Panels
398 x 421 x 3mm
Right Side Panel
448 x 381 x 15mm
Back Kick Panel
394 x 78 x 15mm
Drawer End Panels
338 x 73 x 15mm
1 Pc 1 Pc
1 Pc
1 Pc 1 Pc
2 Pcs
1 Pc
Front Strengthening Panel
394 x 78 x 15mm
1 Pc
2 Pcs
2 Pcs
MQTY
Drawer Base Panels
366 x 342 x 3mm
2 Pcs
2 Pcs

HODEDAH ®
www.Hodedah.com
The Breakdown
HODEDAH ®
www.Hodedah.com 7| Page
The Breakdown

HODEDAH ®
www.Hodedah.com 8| Page
Step 1
11 Nail Leg
4 Pcs.
9Mini Fix
4 Pcs.
9Mini Fix
4 Pcs.
1Pvc Dowel
4 Pcs.
5
Screw M6.2 x 10mm
8 Pcs.
PANEL A
PANEL
F
PANEL
G
A. Place the drawer slide A ⑬
onto the 2 holes area shown
at stand panel Aand I. Then
tighten it with 2 screws ⑤.
B. Nail Protection Nail ⑪,
provided with hammer
onto the bottom edge
of panel Aand Fas
shown.
D. Insert the PVC dowels ①to panel Aand F ’s
non-thru holes as shown, using hammer to tap them in.
C. Insert the mini fix ⑨
(nuts) with the cross
arrow mark facing
upward and aim to
panel A & F 's top
thru holes. (As shown)
Insert, push down and tighten mini fix
screw ⑨, to the hole as shown (Panel G)
Step 2

HODEDAH ®
www.Hodedah.com 9| Page
Step 3
6
Screw M6 x 40mm
6 Pcs.
Fix Panel B, C, D & E onto Panels Fby inserting the dowels
onto the non-thru holes at Panel F.
Next, fix Panel Aonto panel B, C, D & E by inserting the
dowels onto the non-thru holes at Panel A.
Use allen key ⑮to tighten 3 screws ⑥from the thru-holes of panel Ato
non-thru hole of panels B, C, D & E as shown.

HODEDAH ®
www.Hodedah.com 10| Page
Step 4
-Fix panel Gonto panels A & F and align properly by inserting the 4
dowels of panels A & F onto the non thru holes of panel G.
-Pushing and light tapping of panel G to have panel A, G & F fix tightly.
-Then, tighten mini fix ⑨clockwise to
lock the mini fix up for tightening panel
G up. Cover 4 mini fix caps provided by
pushing the cover 's stem onto the hole
of mini fix nut on upper side of panel
Aand F.

HODEDAH ®
www.Hodedah.com 11| Page
Step 5
12 Nail
12 Pcs.
7Pvc Cap
6 Pcs.
Place the back Panels Ionto the back of the main unit. Then align them properly for
nailing. Then use hammer to nail the nails one by one and at center of 4 side
edges. Gap between 2 nails should be about 100mm for all. Cover all the screws ⑥'s
head with the PVC cap provided by pushing the cover's stem onto the hole of screw
head one by one for all screws on panels Aand F.

HODEDAH ®
www.Hodedah.com 12| Page
9Mini Fix
4 Pcs.
9Mini Fix
4 Pcs.
1Pvc Dowel
14 Pcs.
PANEL
E
PANEL
B
PANEL
C
PANEL
D
PANEL
H x2
PANEL
J x2
PANEL
K x2
Step 6
B. Insert the PVC dowels ①to panel B,C,D,E,J and K ’s non-thru holes as
shown, using hammer to tap them in.
A. Insert the mini fix ⑨(nuts) with the cross arrow mark facing upward and aim to
panel J & K 's top thru holes. (As shown)
C. Insert, push down and tighten mini fix screw ⑨, to the hole as shown (Panel H)

HODEDAH ®
www.Hodedah.com 13| Page
Assembly Of Drawers
3
Screw M3.5 x 14mm
12 Pcs. 4
Screw M4 x 32mm
8 Pcs. 8Handle
2 Pcs. 8
Screw M4 X 20mm
4 Pcs.
(1)
12 Nail
14 Pcs.
(2)
2
M3x16mm Screw
2 Pcs. 10
Backply Stopper
2 Pcs.
x2
-Place panel Kand J on each side of panel H
with Panel K and J 's PVC dowel insert to panel
H 's non-thru hole and Panel H 's mini fix screws
insert into Panel K and J 's thru as shown.
Then tighten mini fix on panel K and J clockwise
to lock mini fix up.
-Next tighten screw ④to panel K and J 's upper
thru holes to fix up to the panel L.
-Flip drawer with
bottom side up, place
panel Monto the
drawer and align
properly. Then nail the
nails provided with
hammer on the border
of panel Mas
shown.The gap
between 2 nails is
about 100mm.
-After that, place a
drawer slide B ⑭with
the small white roller
facing outward and
with other end tip
touching panel Honto
each bottom side
(angle) edge of panel
Jand K. Then tighten
3 screws ③on each
drawer slide B ⑭(as
shown).
Put the backply stopper ⑩onto
panel Mwith the shorter part
touching panel H, then tighten
it with screw ②.
-Flip the drawer over.
-Tighten 2 screw ⑧from inner side of panel Hinto the handle ⑧holes.
(3)

HODEDAH ®
www.Hodedah.com 14| Page
Step 7
Take drawers and slide them (the white rollers at drawer slide at both side of
drawers are to go into the track of the slides at each side panel.) all the way
gently, one drawer by one drawer starting from bottom one.

HODEDAH ®
www.Hodedah.com
Job Complete
15| Page
In the interest of our environment please dispose of all packaging thoughtfully.
Enjoy & Thank you for purchasing from Hodedah!

HODEDAH ®
www.Hodedah.com
TP 6#x5/8'' Screw
2Pcs.
Mounting bracket
4Pcs.
Restraint strap
2Pcs.
·Attach the mounting bracket a to the furniture in the
solid part below the top panel a few inches away from the
side of the unit.
·Screw b through the smallest hole of a .
FITTING OF ANTI-TIP SAFETY STRAP
STEP 1:
STEP 2:
·Locate a stud in the wall
behind the unit,does not
have to be centered.
·Place the other mounting
bracket a on the wall
stud 2 inches below the
mounting bracket
secured to the back of
your unit.
·Attach to the wall stud
using c through the
smaller hole of a .
·Repeat the same step a few inches away from
the other side of the unit.
·Place the furniture into position so both mounting
brackets are vertically in line.
·Lace the end of the restraint strap through the
larger holes in each mounting bracket.
·Secure the straps and lock into place.
STEP :
TP 8#x2'' Screw
2Pcs.
BACK SIDE OF
TOP PANEL
WALL
FURNITURE
16| Page