Hodedah HI5DR-A User manual

1 | P a g e
www.Hodedah.com
Assembly Instructions
This instruction booklet contains important safety information, please read and keep for future reference.
ITEM # HI5DR-A
5 DRAWER CHEST
FRONT VIEW BACK VIEW
Product Dimensions: Height 48” x Width 31.5” x Depth 15.75”
Weight Capacity per drawer: 20 lbs.
2 people
90mins
1 YR LTD
1 Box

2 | P a g e
www.Hodedah.com
Questions, need parts, we are here to help!
FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READY
DO NOT RETURN PRODUCT TO THE STORE
If parts are missing or damaged please contact our customer service team and we will
gladly ship your replacement parts FREE of charge within ONE YEAR of purchase!
______________________________________________
WARRANTY
Hodedah warrants this product to be free from defects in materials and workmanship and agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is solely
limited to replacement of defective parts and no assembly for labor is included. This warranty does not
apply to any product that has been improperly assembled, subjected to misuse, abuse or which has been
altered or repaired in any way. To obtain warranty service, original purchaser must present the following;
original bill of sale, date of purchase, where the product was purchased and images if applicable.
Components replaced warranted through the remainder of the original warranty only. The defective part
will be replaced without charge, subject to the terms and conditions described above.
WARNING
This product contains small parts, keep away from children.
This product contains plastic bags, keep away from children.
Serious or fatal crushing injuries can occur from furniture tip-over. To help
prevent this, place heaviest items on the lower shelves and drawers. Do not set
heavy objects on top shelves and drawers.
Never allow children to climb or hang on drawers, shelves and doors.
Phone
Mon –Fri | 9:30 am to 5pm EST
1 - 855 –HODEDAH
1 –855 –463 -3324
Email
Send us an email
[e-mail]
Website
Visit our website to open a case
www.Hodedah.com

3 | P a g e
www.Hodedah.com
Never open more than one drawer at a time.
The use of tip-over restraints may reduce but not eliminate the risk of tip-over.
Let’s get started…
Helpful hints, read before beginning assembly
Make sure you receive all boxes. If your item is packed in one box, box count will read 1
of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and second
box will read 2 of 2.
Read each step carefully. It is very important that each step is performed in the correct
order. If these steps are not followed in sequence, assembly difficulties will occur.
Work in a spacious level area, preferably carpet, near the place the unit will be used.
DO NO USE power tools to assemble your furniture, it will strip and damage parts.
Your package should include the following hardware and parts. Parts are labeled or
stamped on the raw edge. Please inspect contents to ensure you have received all
components. If you are missing any hardware or parts please contact customer
service right away before assembly.
Assembly Tools Required(not supplied)
Hammer Phillips Screwdriver Tape Measure No Power Tools Needed
____________________________________________________________________________________
Product Care and Maintenance
Wipe clean with dry soft cloth, never use chemicals or cleaning products that will
damage the finish.
Avoid placing your furniture in direct sunlight, as sunlight causes fading.
Never push, drag or pull your furniture, to move to a new location carefully with two or
more people carry the unit to its new location.
Avoid extreme changes in temperature by arranging furniture away from radiators, heat
and air vents and air conditioning units.

4 | P a g e
www.Hodedah.com
Hardware List
A
PVC Dowel
QTY
48Pcs
B
Minifix
QTY
19Sets
C
Screw M4x45mm
QTY
45Pcs
D
Screw M3.5x16mm
60Pcs
E
Screw M4x25mm
10Pcs
F
Sticker
20Pcs
G
Handle (160mm)
5Pcs
H
Drawer Slide
(300mm)
5Sets
I
Leg
4Pcs
Important
1. Before you throw the package, please use the Check Box to identify the parts and hardware to
ensure that you have everything you need.
2. Check and measure the bolts before applying them to parts.
3. Do not completely tighten all hardware until the entire assembly is complete, unless indicated
otherwise.

5 | P a g e
www.Hodedah.com
Parts List
1 Left Side Panel
1200x380x15mm
QTY
1Pc
2 Right Side Panel
1200x380x15mm
QTY
1Pc
3 Top Strengthening
LVL Panel
758x65x16mm
QTY
1Pc
4 Back Panel
758x396x15mm
3Pcs
5 Front
Strengthening Panel
758x70x15mm
4Pcs
6 Kick Panel (Front)
758x95x15mm
1Pc
7 Top Panel
800x400x15mm
1Pc
8Drawer Support
Panel
335x50x15mm
5Pcs
9 Drawer Base
Panel
710x344x2.5mm
5Pcs
10 Drawer Front
Panel
778x217x15mm
5Pcs
11 Drawer –Left
Side Panel
350x116x15mm
5Pcs
12 Drawer –Right
Side Panel
350x116x15mm
5Pcs
13 Drawer End
Panel
701x116x15mm
5Pcs

6 | P a g e
www.Hodedah.com
The Breakdown…
10
11
12
13
98
1
7
2
6
4
5
3
5
5
5
4
4

7 | P a g e
www.Hodedah.com
In hardware list, you will find five bundles of drawer slide (H), here you need to
differentiate left and right as shown in picture below.
Left Drawer Slide(H)
Flat Shaped - Left
"L" Shaped - Left
Right Drawer Slide(H)
Flat Shaped - Right
"L" Shaped - Right

8 | P a g e
www.Hodedah.com
Step 1
Insert PVC dowel (A) to Panel 1, 2, 3, 4, 5, 6, 11 and 12’s non-thru holes as shown,
using hammer to gently tap them in.
Non-thru holes (are small indents in the wood that show you where the screws should
be.)

9 | P a g e
www.Hodedah.com
Step 2
2
Insert the minifix (B) nut
with the cross arrow
mark facing upwards,
you will be able to see
the opening of the Nut
(B) thru the top edges
of panel 2.
Place the flat shaped - right
of the drawer slide (H) at
the predrilled holes on the
panel 2 as shown . Then
tighten the drawer slide
(H) with 3 screws (D).
H
D
Insert Nail (I) protection
onto the bottom edge of
panel 2,slightly tapping
them in with a hammer.
I
H
I
1
Place the flat shaped - left
of the drawer slide (H) at
the predrilled holes on the
panel 1 as shown. Then
tighten the drawer slide
(H) with 3 screws (D).
Insert the minifix (B) nut
with the cross arrow
mark facing upwards,
you will be able to see
the opening of the Nut
(B) thru the top edges
of panel 1.
Insert Nail (I) protection
onto the bottom edge of
panel 1,slightly tapping
them in with a hammer .

10 | P a g e
www.Hodedah.com
Step 3
*Place and fix panel 3, 4, 5 and 6 onto panel 1 by inserting the (Left) dowels onto the
non-thru holes at panel 1 by slightly tapping them in with hammer.
*Insert and fasten screws (C) (Using predrilled holes on panel 1) into the panel 3, 4, 5
and 6 by using screwdriver.
*Cover all the screws (C)' head with sticker (F) provided by stick up onto hole of screw
(C)' heads one by one.
1
4
5
3
5
55
4
4

11 | P a g e
www.Hodedah.com
Step 4
*Place and fix panel 3, 4, 5 and 6 onto panel 2 by inserting the (Right) dowels onto the
non-thru holes at panel 2, then slightly hammer all in from outside of panel 2.
*Fasten screws (C) from the outside of panel 2 by using the predrilled holes to
attach panel 3, 4, 5 and 6.
*Cover all the screws (C)' head with sticker (F) provided by stick up onto hole of screw
(C)' heads one by one.
5
4
6
2
3
1
5
5
5
4
4

12 | P a g e
www.Hodedah.com
Step 5
*First prepare panel 7.
*Place minifix (B) long piece onto the holes of panel 7. (You will use 4 pcs)
*Fix panel 7 onto panel 1 and 2 align properly by inserting the 4 dowels of panel 1 and 2
onto the non-thru holes of panel 7. (Slightly hammer it in)
*Gently tap the panel 7 to connect panel 1 and panel 2 firmly.
*Tighten minifix (B) clockwise to lock minifix up by going under panel 7 and tighten it
upon both sides and middle pieces (Panel 1, 2, and 3).
1
2
5
6
3
7
5
5
5
7

13 | P a g e
www.Hodedah.com
Step 6
Assembly Of Drawer : 5 Drawers
10
*Insert the minifix (B)
X5
*Insert the minifix (B)(nuts)
with the cross arrow mark
facing upward and aim to
panel 8,11 and 12 's top thru
holes.(As shown)
*Insert panel 9 into the
drawer and align properly.
(As shown)
*Insert panel 8,11,12 onto
panel 10 by slightly hammering
the dowels.
X5

14 | P a g e
www.Hodedah.com
*Place panel 13 on each side of panel 11 and 12 as shown.
*Then, tighten screws (C) to panel 11 's upper thru holes to fix them onto panel 13.
*Next tighten screws (C) to panel 12 's upper thru holes to fix up to the panel 13.
*Tighten screws (C) to panel 13 's upper thru holes to fix up to the panel 8.
*Flip the drawer over.
*Tighten 2 screws (E) from
inner side of panel 10 into
the handle (G) holes.

15 | P a g e
www.Hodedah.com
Place the “L” shaped drawer slide (H) with the small white roller facing outward and
should be in parallel with drawer front panel 10. Then tighten 3 screws (D) on each
drawer slide (H).
12
H
D
H
D
D
H
X5
H
H
11
"L" shaped - right
of the drawer
slide stick to the
end of drawer
front panel 10.
10
"L" shaped - left
of the drawer
slide stick to
the end of
drawer front
panel 10.

16 | P a g e
www.Hodedah.com
Step 7
*Take all drawers, and slide them (the white rollers at drawer slide at both side of
drawers are to go into the track of the slide at each side panel.) All the way gently, one
drawer by one drawer starting from bottom to the top accordingly.
7
2
10
10
10
10
10
6

17 | P a g e
www.Hodedah.com

18 | P a g e
www.Hodedah.com
Job Complete…
7
2
10
10
10
10
10
6
Enjoy &Thank you for purchasing from Hodedah!