Hodedah HIBT 60-MOPV User manual

1
Hodedah
www.hodedah.com
support @hodedah.com
ASSEMBLY INSTRUCTION
HIBT 60-MOPV (SINGLE BED)
~ Before assembly, please read the instructions ~
~ Keep these instructions for future reference ~
~ Follow these steps to assemble the Bed ~
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT INFORMATION ABOUT ASSEMBLY
AND SAFETY. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

2
Hodedah
www.hodedah.com
support @hodedah.com
Parts
1
The parts of the product are packed in one box.
There are inner box(es) or package(s) that included components
and accessories required to complete the assembly
I) Main Unit :
II) Drawer :
2
43
6
5
8
7-1
13
14 15 16
17 18 19
7-3
89
10 11
14
16
15 15
17
13
18
19
5
12
2
6
3
4
5
12
Headboard Stand Panel
1 pc
1039 x 600 x 15mm
Headboard Left Side Panel
1 pc
975 x 238 x 15mm
Headboard Fixed Panel
1 pc
1039 x 237 x 15mm
Center Panel
1 pc
1905 x 354 x 15mm
Left Side Rail
1 pc
1905 x 392 x 15mm
Headboard Back Panel
1 pc1
1064 x 385 x 2.5mm
Headboard Top Panel
1 pc
1075 x 240 x 15mm
9
11
Front & Back Strengthering
Panel (Headboard)
2 pcs
1039 x 65 x 25mm
Headboard Right Side
Panel
1 pc
975 x 238 x 15mm
12
Front Panel
2 pcs
1050 x 395 x 15mm
Drawer Front Panel
3 pcs
629 x 190 x 15mm
Left Side Panel (Lower)
1 pc
400 x 45 x 15mm
Mattress Panel
4 pcs
990 x 475 x 15mm
Stand Panel (Side Rail)
2 pcs
487.5 x 294 x 15mm
10
Right Side Rail (Upper)
1 pc
1905 x 130 x 15mm
Right Side Rail (Lower)
1 pc
1905 x 65 x 15mm
Drawer End Panel
3 pcs
571 x 117 x 15mm
Drawer Base Panel
3 pcs
400 x 581 x 2.5mm
Drawer Side Panel
6 pcs
400 x 140 x 15mm
7-2
7-1
9
12
12
12
7-2
7-3
89
10 11
9
89
10 11
9

25MM
3
Hodedah
www.hodedah.com
support @hodedah.com
Hardware And Accessories
IMPORTANT
Check the measure of the bolts on the scale below or with
a measuring tape before applying them in the parts
Observe correctly the application and the position of each bolt
accessory, as the step-by-step instructions, before applying
them in the parts.
Plastic Dowel
M8 x 25mm
46 pcs
ACB Screw
M3.5 x 12mm
36 pcs
BCCB Screw
M4 x 25mm
6 pcs DCB Screw
M4 x 30mm
6 pcs E F
GMinifix 5654
- Housing
9 pcs
Minifix 5654
- Screw
9 pcs
Pvc Cap
18 pcs
Nail
58 pcs
Drawer Slide - A
400mm
6 pcs
* Fix On Panels # 5 & 7
Drawer Slide - B
400mm
6 pcs
* Fix On Drawer Side Panels
12MM 30MM
Required Or Recommended Tools
IMPORTANT !
The required or recommended tools for
assembly are not supplied with the product.
Sample Screwdriver Sample Hammer Sample Measuring Tape Sample Electric Screwdriver
010 20 30 40 50 60 70 70
Plastic Pin
24 pcs
J2
NO1 O2
K
J1
CSK Cap Screw
M6 x 40mm
14 pcs
40MM
CB Screw
M4 x 35mm
46 pcs
35MM
Allen Key
1 pc
L1 Handle IP994
96mm - Pvc
3 pcs
P/H Screw
M4 x 40mm
6 pcs
H
JCBC Bolt
M6 x 50mm
12 pcs
50MM
I
Barrel Nut
12 pcs
L2 M

- This product contains small components, please ensure that they are
kept away from small children.
- THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE
REFERENCE.
STOP
DO NOT RETURN PRODUCT TO THE STORE.
If a part is missing or damaged, email our customer
service. We will gladly ship your replacement parts
FREE of charge.
email us at
[email protected]
For prompt, reliable service; please have your
assembly manual ready.
Need Parts or Assistance?
4
Hodedah
www.hodedah.com
support @hodedah.com

Thank you for purchasing from Hodedah
To learn more about hodedah and our products visit
www.hodedah.com
READ BEFORE BEGINNING ASSEMBLY
- Read each step carefully. It is very important that each step of instruction is performed in the
correct order. If these steps are not followed in sequence, assembly difficulties will occur.
- Make sure all parts are included. Most parts are labeled or stamped on the raw edge.
- Work in spacious area, preferably on a carpet, near the place the unit will be used.
- Do not use power tools to assemble your furniture. Power tools may strip or damage the parts.
HELPFUL HINTS
- Call us if you need assistance.
- Move your new furniture carefully, with two people lift and carry the unit to it's new location.
- Never push, drag or pull your furniture (especially on carpet).
Warranty Information
Hodedah warrants this product to be free from defects in material and workmanship agrees to
remedy any such defect. This warranty covers one year from the date of original purchase. This is
solely limited to be repair or replacement of defective parts and no assembly labor is included.
This warranty does not apply to any product which has been improperly assembled, subjected to
misuse or abuse or which has been altered or repaired in any way.
To obtain warranty, purchaser must present original bill of sale. Components repaired or
replaced warranted through the remainder of the original warranty period only. The defective
components will be repaired or replaced without charge, subject to the terms and conditions
described above.
For help with assembly, identifying parts, product information or to
order parts, please contact us :
Call us at :
718-456-0505
Monday - Friday
9:00am - 5:00pm
Visit our website :
www.hodedah.com
5
Hodedah
www.hodedah.com
support @hodedah.com

Hodedah
www.hodedah.com
support @hodedah.com
6
Hodedah
www.hodedah.com
support @hodedah.com
Pre - Assembly
Insert 4 Pvc Dowel A into the edge of Panel #1, 4 & 6
where are non-thru holes indicators, using hammer
gently tap them in.
AA
M
M
PANEL #13 & 17
A
A
MA
A
M
PANEL #16
A
A
A
A
PANEL #1
A
A
A
A
PANEL #6
M
M
M
A
A
M
M
M
PANEL #4
M
M
M
A
A
PANEL #15
A
A
A
A
PANEL #15
A
A
Using a hammer gently tap the 3 Plastic Pin M
into the bottom edge of Panel #1, 4 & 6.
Insert Pvc Dowel A into the edge of Panel #13, 16 & 17
where are non-thru holes indicators, using hammer gently
tap them in.
Using a hammer gently tap the Plastic Pin M into
the bottom edge of Panel #13, 16 & 17.
Insert Pvc Dowel A into the edge of Panel #15 where are non-thru holes indicators, using hammer gently tap them in.
A
A
M
A
A

Place the drawer slide O1 onto
the 3 marking area shown at
side Panel #2. Then tighten it
with 3 screw B.
A
A
A
A
PANEL #14
A
A
A
A
PANEL #2x2
(Left View)
PANEL #2x2
(Right View)
M
M
A
A
A
A
M
M
J2
J2
A
A
A
A
PANEL #3
PANEL #5
M
M
PANEL #5
M
M
7
Hodedah
www.hodedah.com
support @hodedah.com
Hodedah
www.hodedah.com
support @hodedah.com
Pre - Assembly
Using a hammer gently tap the 3
Plastic Pin M into the bottom edge of
Panel #9, 11 & 13.
Insert 4 Pvc Dowel A into the edge of
Panel #2, 5 & 7 where are non-thru
holes indicators, using hammer gently
tap them in.
Using a hammer gently tap the 3
Plastic Pin M into the bottom edge of
Panel #2, & 5.
Insert 4 Pvc Dowel A into the edge of
Panel #3 where are non-thru holes
indicators, using hammer gently tap
them in.
Insert 4 Minifix screw J2 to Panel #3,
14 & 18non-thru holes as shown.
Place the drawer slide O1 onto
the 3 marking area shown at
side Panel #5. Then tighten it
with 3 screw B.
BO1
J2
J2 J2
J2 J2
J2
J2
PANEL #18
B
B
BBB
B
B
BO1
O1 BBB

- Place Panel #7-1 on each side of Panel #9 as shown.
- Then, tighten screw F to Panel #9 lower thru
holes to fix them onto Panel #7-1.
- Place Panel #8 on upper side of Panel #9 as shown.
- Next tighten screw E to Panel #9 upper thru
holes to fix up to the Panel #8.
( 2 )
( 3 )
- Flip drawer upside down, place Panel #10
onto the edges of Panel #9. Then, use Nails I &
gently hammer the borders of Panel #8 spacing it
every 3 to 4 inches.
- Place the Drawer Slide O2 with small white
roller facing outward and the end of the tip
touching opposite panel. Then tighten each 3
screws B on side Panel #9.
- Place Panel #11 into the drawer base and tighten
screw E to fix up to the Panel #7 & 8.
( 4 )
- Flip the drawer over.
- Tighten 2 screw L2 from inner side of Panel #7-1, 7-2 & 7-3
into the Handle L1 holes.
COMPLETED
( 5 )
Assembly Of Drawer
8
Hodedah
www.hodedah.com
support @hodedah.com
- Tighten 2 screw C to Panel #7-1 inner thru hole.
- Repeat same step foe next Panel #7-2 & 7-3.
7-1
( 1 )
7-1, 7-2 & 7-3
9
8
C
C
9
L1
BO2
O2
I
L2
L2
11
E
10
E
9
9
9
7-1, 7-2 & 7-3
E
E
E
E
E
E
BB
BB
B

9
Hodedah
www.hodedah.com
support @hodedah.com
Assembly Instruction Set A Step 1
- Fix both Panel #2 onto Panel #1 by inserting the dowels onto the respective non-thru holes at Panel #1.
- Use Allen Key N to tighten 4 screw F from the thru-holes of Panel #1 to non-thru hole of both Panel #2, as shown.
CSK Cap Screw
M6 x 40mm
4 pcs
FAllen Key
1 pc
40MM
CAUTION When inserting the Dowels to non-thru holes, don't push to hard. Otherwise, the side panels (2)
may be damage.
N
- Fix Panel #3 onto Panels #2 upper . Align properly by inserting the dowel of Panel #3 onto non-thru holes of Panels #2.
- Pushing & light tapping of Panel #3 to have Panel #2 & 3 fix tightly.
- Insert 2 Minifix Housing J1 onto non-thru holes at Panel #2.
- Fix Panel #4 onto Panels #2 lower. Align properly by inserting the dowel of Panel #4 onto non-thru holes of Panels #2.
- Pushing & light tapping of Panel #4 to have Panel #2 & 4 fix tightly.
- Insert 2 Screw G onto thru holes at Panel #4. Use Allen key P to tighten all the Screws G & Minifix J1.
J1 N
F
N
12
2
3
4
CSK Cap Screw
M6 x 40mm
2 pcs
F
40MM
Minifix Housing
5654
2 pcs
2
2
F
FN
J1
F
F
F
J1
N

5
10
Hodedah
www.hodedah.com
support @hodedah.com
Assembly Instruction Set A Step 2
Barrel Nut
4 pcs
HAllen Key
1 pc
CAUTION When inserting the Dowels to non-thru holes, don't push to hard. Otherwise, the side panels (1,
3, 4 & 6) may be damage.
N
- Fix Panel #6 onto Panels #5. Align properly by inserting the dowel of Panel #6 onto non-thru holes of Panels #5.
- Pushing & light tapping of Panel #6 to have Panel #5 & 6 fix tightly.
- Insert 2 Barrel Nuts H to non-thru holes at Panel #6.
- Then, insert 2 Screw G onto thru holes at Panel #5. Use Allen key N to tighten all the Screws G.
Allen Key
1 pc
3
4
5
- Fix Panel #5 onto Panel #1 by inserting the dowels onto the respective non-thru holes at Panel #1.
- Insert 2 Barrel Nuts H to non-thru holes at Panel #1, 3 & 4.
- Use Allen Key N to tighten 4 screw G from the thru-holes of Panel #5 to non-thru hole of both Panel #1, 3 & 4, as shown.
6
N
G
1
G
G
G
H
H
H
HJCBC Bolt
M6 x 50mm
4 pcs
G
50MM
Barrel Nut
2 pcs
JCBC Bolt
M6 x 50mm
2 pcs
50MM
G
G
N
H
H
GHN