Hoist Fitness HD1400 User manual

Note: Both Serial Number and Model Number are Required when Ordering Parts
OWNERS MANUAL
RECORD SERIAL NUMBER HERE Customer Service
Fa x
[phone]
[phone]
[phone]
HD1400
LEG EXTENSION/CURL
CATALOG NUMBER
0302-001

INSTRUCTIONS (Step 1)..............................................................
FRAME ASSEMBLY (Step 2).........................................................
CABLE ASSEMBLY (Step 3)..........................................................
SHIELD ASSEMBLY (Step 4).........................................................
HARDWARE LISTING ..................................................................
DECAL PLACEMENT ...................................................................
GENERAL MAINTENANCE INFORMATION ............................
MAINTENANCE SCHEDULE........................................................
LIMITED WARRANTY ..................................................................
PRE-ASSEMBLED PARTS (Step 5)................................................
PARTS LISTING ............................................................................
BOLT SIZING CHART ..................................................................
WASHER SIZING CHART ............................................................
WEIGHT RATIOS............................................................................
WEIGHT TRAINING TIPS.............................................................
WEIGHT TRAINING EXERCISE LOG ......................................
Page - 1 HD1400 Assembly
CONTENTS
2
4
15
17
19
21
22
23
25
27
29
31
33
37
39
40
OWNERS
MANUAL

Page - 2HD1400 Assembly
INSTRUCTIONS
Socket Wrench
(9/16”, 1/2”)
3/4" Open End Wrench
Standard Allen Wrench set
(5/64” thru 1/4”)
Crescent Wrench
Rubber Mallet
Tape Measure
External snap ring pliers with a
tip size between .035" ~ .043".
TOOLS REQUIRED
Before beginning assembly please take the time to read the
instructions thoroughly. Please use the various lists in this
manual to make sure that all parts have been included in your
shipment.
Use only Hoist replacement parts when servicing.
Failure to do so will void your warranty and could result in
personal injury.
Hoist equipment is designed to provide the smoothest, most
effective exercise motion possible. After assembly, you should
check all functions to ensure correct operation. If you
experience problems, first recheck the assembly instructions to
locate any possible errors made during assembly. If you are
unable to correct the problem, call your authorized Hoist dealer.
Be sure to have your serial number and this manual when
calling. When all parts have been accounted for, continue on .
When ordering use the part number and description
from the lists.
OWNERS
MANUAL

Page - 3 HD1400 Assembly
OWNERS
MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK******THIS PAGE WAS INTENTIONALLY LEFT BLANK***

FRAME ASSEMBLY
Step 2
Page - 4HD1400 Assembly
OWNERS
MANUAL

FRAME ASSEMBLY
Step 2a
1 - Weight Frame Upright
2 - Weight Cage Top Mount
3 - Weight Stack Mount
4 - Main Support Frame
5 - Rear Upright
6 - Main Frame Support
7 - Right Side Handle
8 - Left Side Handle
Part Descriptions
A - 1/2”-13UNC x 4 3/4” Hex Bolt
B - 1/2”-13UNC x 3” Hex Bolt
E - 1/2”-13UNC x 3 1/4” Hex Bolt
AA - 1/2” Flat Washer
BA - 1/2” Nylok Nut
CA - Rubber Foot Pad
Hardware Descriptions
Page - 5 HD1400 Assembly
OWNERS
MANUAL
Start assembly by bolting both (1)’s, to (2). Then bolt (3) to the
bottom of both (1)’s. Attach the top of (5) to (2), and the bottom of (5)
and (4) to (3). Bolt (6), (7), and (8) to (4). bolts.Wrench Tighten

Page - 6HD1400 Assembly
OWNERS
MANUAL
CA
CA
6
B
B
7
AA
??
??
?
B
?
AA
AA
1
AA
2
1
CA
AA
CA BA
B
AA
AA
AA
BA
A
AA
??
??
?
AA
?
CA
??
??
?
?
?
?
AA
AA
4
BA
AA
AA
B
5
3
E
BA
8
AA
BA BA
AA
AA

FRAME ASSEMBLY
Step 2b
1 - Weight Frame Upright
2 - Weight Cage Top Mount
3 - Weight Stack Mount
9 - Guide Rod
10 - 12 ½ LB Intermediate Plate
11-8¼LBIntermediate Plate
12-8¼LBTopPlate
Part Descriptions
E - 1/2”-13UNC x 3 1/4” Hex Bolt
N - 5/16”-UNC x 5/16” Socket Set Screw (WZ)
AA - 1/2” Flat Washer
BA - 1/2” Nylok Nut
CB - Weight Stack Bumper
CG - Guide Rod Top Mount
Hardware Descriptions
Page - 7 HD1400 Assembly
OWNERS
MANUAL
Start by sliding (9) through (CB) and slide them both into (3). Tilt
both (9)’s forward enough to allow room to slide the weights on. Slide all
10 (10)’s, and all 5 (11)’s on to both (9)’s. Now slide (12) onto both (9)’s.
Slide (CG) on both (9)’s and angle both (9)’s vertical and secure (CG) to
both (1)’s and (2). Secure both (9)’s to (CG) using set screw (N). Wrench
Tighten all bolts.

AA
Page - 8HD1400 Assembly
BA
N
N
AA
CG
E
OWNERS
MANUAL
3
1
2
12
10
11
9
9
CB
AA
1

FRAME ASSEMBLY
Step 2c
1 - Weight Frame Upright
4 - Main Frame
13 - Left Side Support Mount
14 - Right Side Support Mount
15 - Left Side Elbow Pad Mount
16 - Right Side Elbow Pad Mount
17 - Leg Extension Mount
Part Descriptions
A - 1/2”-13UNC x 4 3/4” Hex Bolt
B - 1/2”-13UNC x 3” Hex Bolt
D - 1/2”-13UNC x 2 3/4” Hex Bolt
AA - 1/2” Flat Washer
BA - 1/2” Nylok Nut
Hardware Descriptions
Page - 9 HD1400 Assembly
OWNERS
MANUAL
Start assembly by bolting (13) and (14) to (1) and (4). Then bolt (15)
and (16) to (4). Bolt (17) to (4). bolts. when
bolting (13) and (14) to both (1)’s, hand tighten bolts (A), they will be
secured in a later step.
Wrench Tighten Note:

Page - 10HD1400 Assembly
OWNERS
MANUAL
?
?
?
?
?
?
?
??
?
?
?
?
?
?
??
?
AA
AA
?
?
D
AA
DAA
D
13
B
D
AA
A
?
?
?
?
BA
16
AA
AA
?
?
?
?
17
BA
BA
AA
?
?
A
14
AA
BA
AA BA
AA
AA
BA
BA
BA
AA
AA
BA
BA
AA
AA D
AA
AA
Hand tighten this bolt,
they will be tightened
in a later step.
Hand tighten this bolt,
they will be tightened
in a later step.
Hand tighten this bolt,
they will be tightened
in a later step.
Hand tighten this bolt,
they will be tightened
in a later step.
15
4
1
1

FRAME ASSEMBLY
Step 2d
17 - Leg Extension Mount
18 - Leg Extension
19 - Lower Swivel Bracket
20 - Dia. .75 x 2.25 LG CRS
Part Descriptions
E - 1/2”-13UNC x 3 1/4” Hex Bolt
AA - 1/2” Flat Washer
BA - 1/2” Nylok Nut
Hardware Descriptions
Page - 11 HD1400 Assembly
OWNERS
MANUAL
Start assembly by sliding (20) into the top of (18) and attach it to
(17). Then slide (20) into the bottom of (18) and attach (19) to (18).
bolts. Check to see that these pivot areas swing freely. If
not, back off Nylock Nut (BA) slightly until both (18) and (19) swing
freely.
Wrench Tighten

Page - 12HD1400 Assembly
OWNERS
MANUAL
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
BA
AA
?
?
20
BA
?
?
?
?
?
?
?
?
?
?
AA
19
AA
AA
18
?
?
?
?
?
?
E
E20
17
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?
?

Page - 13 HD1400 Assembly
OWNERS
MANUAL
FRAME ASSEMBLY
Step 2e
4 - Main Frame
15 - Left Side Elbow Pad Mount
16 - Right Side Elbow Pad Mount
17 - Leg Extension Mount
18 - Leg Extension
19 - Lower Swivel Bracket
21 - Roller Pad Bar
Part Descriptions
F - 3/8”-16UNC x 1” Flat Head Screw
G - 5/16”-18UNC x 4” Hex Bolt
H - 5/16”-18UNC x 1 1/4” Hex Bolt
AC - 5/16” Washer
AE - 5/16” Lock Washer
CH - 3/8” Flat Head Cap
CN - Upholstery Pad
CP - Upholstery Pad
CQ - Pad Assembly
DC - Roller Pad
DE - Plastic Washer
Hardware Descriptions
Start assembly by sliding one (21) through (18), and another (21)
through (19). Bolt two (DC)’s to each (21)’s. Then secure (CN) to (15),
and repeat step for (CP) to (16) (shown assembled for clarity). Next bolt
(CQ) to (4) and (17). bolts.Wrench Tighten

H
AC
AC
AE
21
CH
??
??
?
?
Repeat assembly for (CP).
(Shown assembled or clarity.)
Repeat assembly for (CP).
(Shown assembled or clarity.)
Page - 14HD1400 Assembly
OWNERS
MANUAL
???????
??
G
AE
??
AE
?
?
?
??
????
AC
AC
F
F
AE
CQ
DC
AC
FCH
G
DC
DC
21
CH
F
CP
CN
AE
G
DC
CH
H
15
4
18
17
19
DE
DE
DE
DE
DE
DE
DE
DE

CABLE ASSEMBLY
Step 3
J - 3/8”-16 UNC x 3” Hex Bolt
AB - 3/8” Flat Washer
BB - 3/8” Nylok Nut
CK - 1/2” Flanged Spacer
CL - 4 1/2” Pulley
CM - 11/16” Flanged Spacer
CR - Leg Extension/Curl Cable
DD - Quick Release Cable Lock
DF - 7/16” External Retaining Ring
K - 3/8”-16 UNC x 2 1/2” Hex Bolt
Hardware Descriptions
Page - 15 HD1400 Assembly
OWNERS
MANUAL
CR
NOTE:
BE SURE CABLE RUNS
BETWEEN THE PULLEY AND
THE GUARD SHAFT.
NOTE:
BE SURE CABLE RUNS
BETWEEN THE PULLEY AND
THE GUARD SHAFT.
NOTE:
BE SURE CABLE RUNS
BETWEEN THE PULLEY AND
THE GUARD BOLT.
NOTE:
BE SURE CABLE RUNS
BETWEEN THE PULLEY AND
THE GUARD BOLT.
FINE TUNING
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-TIGHTEN
JAM NUT.
FINE TUNING
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-TIGHTEN
JAM NUT. 182 7/8” (4645mm)
WARNING:
CABLE BOLT MUST BE THREADED
A MINIMUM OF 1/2” INTO ITS RECEIVER
WITH JAM NUT TIGHTENED SECURELY TO
ENSURE PROPER CONNECTION.
WARNING:
CABLE BOLT MUST BE THREADED
AMINIMUM OF 1/2” INTO ITS RECEIVER
WITH JAM NUT TIGHTENED SECURELY TO
ENSURE PROPER CONNECTION.

Page - 16HD1400 Assembly
OWNERS
MANUAL
See Quick Release Cable
Anchor Detail
For Assembly.
AB
BB
CK
CK
AB
CK
K
K
CK
CL
CM
CM
J
BB
BB
K
CL
CL
CR
Warning - Cable Bolt must be threaded
a minimum of 1/2” into the Weight Plate
Stem with Jam Nut tightened securely to
ensure proper connection.
DF
CR
DD
K
K
Quick Release Cable Anchor Detail
With Retaining Ring Assembly.

SHIELD ASSEMBLY
Step 4
22 - Frame Shield
Part Descriptions
L - 1/2”-13 UNC x 4 1/2” Hex Bolt
M - 1/4”-24 UNF x 5” Button Head Bolt
AA - 1/2” Flat Washer
AD - 1/4” Flat Washer
BA - 1/2” Nylok Nut
BC - 1/4” Nylok Nut
CS - Placard (Right)
CT - Placard (Left)
DB - Spacer
Hardware Descriptions
Page - 17 HD1400 Assembly
OWNERS
MANUAL
Attach (22), (CS), and (CT) as shown. bolts.Wrench Tighten
*IMPORTANT*
Now that the Hd1400 machine is completely assembled take time
to assure that your unit is assembled square and perpendicular. To
check this use a Level to check that the Guide Rods are perpendicular
in both directions. If they are not perpendicular in both directions. It
will be necessary to loosen some Frame hardware to re-align the Frame
and re-tighten bolts.

Page - 18HD1400 Assembly
OWNERS
MANUAL
22
AA
BA
AA
BA
L
AA
L
AA
Use existing
hardware
(Both sides)
Use existing
hardware
(Both sides)
Use existing
hardware
Use existing
hardware
Detail A
Rotated for clarity
Detail A
Rotated for clarity
See Detail ASee Detail A
AD
BC
AD
BC
DB
DB
M
M
CT
CS
Repeat process
for (CS)
Repeat process
for (CS)

PRE-ASSEMBLY
Step 5
4 - Main Frame
7 - Right Side Handle
8 - Left Side Handle
12-8¼lbTopPlate
17 - Leg Extension Mount
18 - Leg Extension
23 - 16 Plate Selector Stem
Part Descriptions
CC - Landyard/Selector Pin Stand Off
CJ - Guide Rod Bushing
CV - 7/16” Roll Pin x 2 3/4” LG
CW - 3/4” Flanged Ball Bearing
CX - End Cap 50mm x 75mm
CY - Bumper
CZ - Closed End Black Foam Grip
DA - Closed End Black Foam Grip
CD - Selector Pin
CE - Lanyard Coil
Hardware Descriptions
Page - 19 HD1400 Assembly
OWNERS
MANUAL