Holman 30091 User manual

Holman
Rancho Cordova, CA 95742
800-343-7486
[e-mail]
20220317R1 DATE: __________________
Installation Guide
30091

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 1
*PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
INSTALLING, AND USING THIS PRODUCT.*
Warning
Always check for wires, fuel tanks and lines, brake lines and other
important vehicle functionality items prior to drilling and installing all
products.
Tools Needed
3/8” Wrench and Socket
25/64” Drill
9/16” Wrench and Socket
7/16” Wrench and Socket
Table of Contents
Parts List..........................................................................................................................................2
Hardware.........................................................................................................................................3
Step 1 ─ Find Front Mounting Locations .........................................................................................4
Step 2 ─ Find Rear Mounting Locations ..........................................................................................5
Step 3 –Attach Lower Legs.............................................................................................................6
Step 4 –Install Upright Frame.........................................................................................................7
Step 5 –Install Upright Frame.........................................................................................................8
Step 6 –Install Strut Bracket...........................................................................................................9
Step 7 –Mount Stop Bracket.........................................................................................................10
Before You Begin
Read all instructions.
DO NOT EXCEED WEIGHT CAPACITY of 150lbs.
ENSURE SAFETY WHEN DRILLING INTO VEHICLE
Instructions are shown using a GM truck bed. Mounting locations will vary in different
applications.

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 2
Parts List

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 3
Hardware

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 4
Step 1 ─ Find Front Mounting Locations
At the front of the bed, near the cab of the truck, determine a
safe location on the truck bed floor where the bottom of the
lower leg can be mounted. Insert the lower leg into the front
corner bracket. The lower leg can be rotated in a multiple of
different orientations in order to pick up the best mounting
location on the bed floor. Be sure the slot in the lower leg aligns
with the mount bolt in the front corner bracket. A spacer may be
needed if the lower leg rests on a ridge in the floor of the truck
bed.
Position the front corner bracket into the corner to allow
mounting in two locations.
Mark all four mounting locations.
Ensure it is safe to drill at all locations. Drill using a 25/64” drill
and install plus nuts at all locations.
Passenger side shown below, can also be installed on driver side.

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 5
Step 2 ─ Find Rear Mounting Locations
At the rear of the bed, position the bracket and the lower leg into
the desired location as in the previous step.
Determine a safe location on the truck bed floor where the bottom
of the lower leg can be mounted. Insert the lower leg into the rear
bracket. The lower leg can be rotated in a multiple of different
orientations in order to pick up the best mounting location on the
floor. Be sure the slot in the lower leg aligns with the mount bolt in
the rear bracket. A spacer may be needed if the lower leg rests
on a ridge in the floor of the truck bed.
Mark all four mounting locations.
Ensure it is safe to drill at all locations. Drill using a 25/64” drill
and install plus nuts at all locations.

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 6
Step 3 –Attach Lower Legs
Attach both lower legs and mount brackets to the truck bed using 1/4"x 1-1/4”
hex head bolts, 1/4" lock washers and 1/4" flat washers and insert into the
previously installed plus nut.
**EXPLODED**
**INSTALLED**

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 7
Step 4 –Install Front Upright Frame
Insert the upright frame into the previously installed front corner bracket. Adjust
to the desired height and secure in place using 3/8” x 3/4" socket head screws.

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 8
Step 5 –Install Rear Upright Frame
Insert the upright frame into the previously installed rear bracket. Adjust to
desired height and secure in place using 3/8” x 3/4" socket head screws.

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 9
Step 6 –Install Strut Bracket
Insert the strut brackets into the previously installed upright frames. Be sure to
place the rubber sleeve over the both pieces as shown. Have the hole in the
rubber sleeve align with the threaded nut on the side of the upright frame.
Adjust to the desired position and secure in place using 3/8” x 3/4" socket head
screws.

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 10
Step 7 –Mount Stop Bracket
Attach the stop bracket to the front upright frame using a 3/8” x 2-3/4” carriage
bolt, a 3/8” flat washer and a 3/8” nyloc nut in the orientation shown.
Adjust the ladder stop to the desired position. Tighten.

Instructions –30091
For Technical Support Call: 800-343-7486, Monday-Friday, 7AM - 4 PM (PST) Page 11
MAKE SURE ALL HARDWARE IS TIGHT.
INSTALLATION IS NOW COMPLETE.