PLEASE READ AND SAVE THESE
IMPORTANT SAFETY INSTRUCTIONS
FEATURES - OPERATIONS
CLEANING/MAINTENANCE
During Season Care:
1. Always unplug the heater before cleaning.
2. Clean the unit with a soft cloth moistened with a mild
soap and water solution.
3. NEVER use abrasive or flammable solvents to clean the
unit.
4. After cleaning, be sure to completely dry the unit with
a cloth or towel.
After Season Care:
1. Store heater in a cool, dry location.
2. It is recommended that you store the unit in its original
carton.
AUTO SAFETY SHUT-OFF
This heater is equipped with a patented, technologically
advanced, safety system that requires the user to reset
the heater if there is a potential overheat situation. When
a potential overheat temperature is reached, the system
will automatically shut the heater off. It can only resume
operation when the user resets the unit. For specific reset
instructions please refer to the unit.
Tip-over Shut-off (for HFH111T only):
When the unit is accidentally knocked over, it will shut
off. To reset, simply place the heater in an upright
position on a level surface.
RESET INSTRUCTIONS
If your heater shuts down:
1) Turn Control to OFF.
2) Unplug the unit and wait 30 minutes.
3) Plug in and operate normally.
TROUBLESHOOTING
If your heater fails to operate:
• Turn the heater OFF and UNPLUG THE HEATER.
• Make sure the electrical outlet or circuit breaker is
working.
• Check for obstructions. If you find an obstruction turn
the heater OFF, and unplug the unit. Carefully remove
the obstruction and follow the reset instructions.
• The temperature may be set too low. Turn the
thermostat knob clockwise until the heater restarts.
• Make sure selector is in LOW or HIGH setting.
Please DO NOT attempt to open or repair the
heater.
TECHNICAL SPECIFICATIONS
• Amps:12.5
• Wattage:1500W(+5%–10%)
• Workingvoltage:120VAC/60Hz
OPERATING INSTRUCTIONS
1. Carefully remove your heater from the box. Please
save the carton for off-season storage.
2. Make sure the unit is in the Off position before
plugging the heater into the outlet.
3. Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.
Mode Control
Turn the Mode Control to the desired setting:
Off Mode
If you want to shut off the heater at any time of
operation, turn the Mode Control to Off position. Power
indicator light will remain lit until the heater is turned to
Off.
Fan only Setting
Heater will run at fan-only operation without heat output.
Low Heat
The heater will run continuously at 1000W.
High Heat
The heater will run continuously at 1500W.
Thermostat Control (for HFH111 & HFH111T ONLY)
1. Before setting the thermostat, allow heater to operate
and warm up the room. As noted before, you need to
turn the Thermostat Control to the highest setting to
start the heater.
2. When the desired temperature comfort level is
reached, lower the thermostat setting until the fan/
heater stops operating. This is done by moving the
Thermostat Control counter-clockwise toward the Low
setting.
3. The control will now automatically maintain the pre-set
temperature level by cycling the heater ON and OFF.
NOTE: To start heater operation, make sure the
Thermostat Control is turned fully clockwise to the highest
position.
NOTE: It is normal for the heater to cycle ON and OFF as
it maintains the preset temperature. To prevent the unit
from cycling, you need to raise the thermostat setting.
CAUTION: FRONT GRILL IS HOT WHEN UNIT IS IN
OPERATION.
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not
let bare skin touch hot surfaces. If provided, use
handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 feet (0.9 m) from the
front of the heater and keep them away from the
sides and rear.
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or
plug or after the heater malfunctions, has been
dropped or damaged in any manner. Discard heater,
or return to authorized service facility for
examination and/or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never
locate heater where it may fall into a bathtub or
other water container.
8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
9. To disconnect heater, turn controls to off, then
remove plug from outlet.
10. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or
exhaust in any manner. Do not use on soft surfaces,
like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside.
Do not use it in areas where gasoline, paint, or
flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any
other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons.
14. Always plug heaters directly into a wall outlet/
receptacle. Never use with an extension cord or
relocatable power tap (outlet/power strip).
15. When unplugging, be sure to pull by the plug and
not the cord.
16. If the heater will not operate, see specific instructions
on Auto Safety Shut-off.
17. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed
by qualified personnel only.
18. Discontinue use if plug or outlet is hot. It is
recommended that the outlet be replaced if plug or
outlet is hot to touch.
19. The heater must not be located immediately below a
socket-outlet. Do not use this heater in the
immediate surroundings of a bath, a shower or a
swimming pool.
SAVE THESE
INSTRUCTIONS
CLEANING / MAINTENANCE
TROUBLESHOOTING
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
If you have any questions regarding your product or
would like to learn more about other Holmes®products,
please contact our Consumer Service Department at
1-800-546-5637 or visit our website at
www.holmesproducts.com.
Figure 1
A. Carry Handle
(not shown)
B. Mode Control
C. Power Light
for HFH110
A
C
B
Figure 2
A. Thermostat Control
B. Carry Handle (not
shown)
C. Mode Control
D. Power Light
for HFH111 & HFH111T
A
C
D
B
LEA Y GUARDE ESTAS
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
CARACTERISTICAS Y FUNCIONAMIENTO
LIMPIEZA / MANTENIMIENTO
Durante la temporada:
1. Siempre desenchufe el calefactor antes de limpiarlo.
2. Limpie la unidad con un paño suave humedecido en
una solución suave de agua y jabón.
3. NUNCA utilice solventes abrasivos o inflamables para
limpiar la unidad.
4. Luego de limpiarla, asegúrese de secar
completamente la unidad con un trapo o toalla.
Después de la temporada:
1. Guarde el calefactor en un lugar frío y seco.
2. Se recomienda guardar la unidad en su embalaje
original.
APAGADO AUTOMÁTICO DE SEGURIDAD
Este calefactor está equipado con un sistema de seguridad
patentado, de tecnología avanzada que requiere que el
usuario reinicie el calefactor en caso de un
sobrecalentamiento potencial. Cuando se alcanza una
temperatura de un posible recalentamiento, el sistema
apagará automáticamente el calefactor. Volverá a
funcionar únicamente cuando el usuario prenda de nuevo
la unidad. Vea la unidad para instrucciones específicas de
reinicio.
Apagado de Inclinación (solo para HFH111T):
Cuando la unidad se cae accidentalmente, se apaga. Para
reiniciarla, simplemente coloque el calefactor
verticalmente sobre una superficie nivelada.
INSTRUCCIONES VOLVER A ENCENDER
Si la unidad se apaga:
1) GIRE el Control a APAGADO.
2) Desenchufe la unidad y espere 30 minutos.
3) Enchufela y vuélvala a operar normalmente.
DIAGNOSTICO DE PROBLEMAS
Si su calefactor no funciona:
• APAGUEelcalefactoryDESENCHÚFELO.
• Asegúresedequeeltomacorrienteollavetérmica
funcionen correctamente.
• Verifiquequenohayaningunaobstrucción.Si
encuentra una obstrucción, apague el calefactor, y
DESENCHUFELO. Quite cuidadosamente la obstrucción
y siga el procedimiento para reiniciar la unidad.
• Eltermostatopuedeestarajustadodemasiadobajo.
Gire la perilla del termostato en sentido de las agujas
del reloj hasta que comience a calentar nuevamente.
• VerifiquequeelControldeModoestéenlaposición
LOW o HIGH.
NO intente abrir o reparar el calefactor.
ESPECIFICACIONES TECNICAS
• Amperes:12,5
• Potencia:1500W(+5%-10%)
• Voltajedefuncionamiento:120vCA/60Hz
INSTRUCCIONES DE USO
1. Saque cuidadosamente el calefactor de la caja.
Conserve la caja para guardarlo en el verano.
2. Asegúrese de que esté en la posición Apagado antes
de enchufarlo en el tomacorriente.
3. Evite sobrecargar el circuito eléctrico evitando utilizar
otro aparato de alta potencia en el mismo tomacorriente.
A 1500 Vatios, esta unidad consume 12,5 Amperes.
Control de modo
Con el Control de modo, seleccione la configuración
deseada:
Modo Apagado
Si desea apagar el calefactor en cualquier momento, gire
el Control de modo hasta la posición APAGADO. La luz del
indicador de encendido permanecerá encendida hasta que
se configure el calefactor en Apagado.
Configuración Sólo ventilador
El calefactor funcionará en la configuración Sólo
ventilador sin emitir calor.
Calor Bajo
El calefactor funcionará continuamente a 1000W.
Calor Alto
El calefactor funcionará continuamente a 1500W.
Control de termostato
(solo para la HFH111 &
HFH111T)
1. Antes de configurar el termostato, permita que el
calefactor caliente la habitación. Como se indicó
anteriormente, para encender el calefactor, debe
girar el control del termostato hasta alcanzar el nivel
más Alto.
2. Al alcanzar la temperatura deseada, disminuya el
ajuste del termostato hasta que el ventilador/
calefactor deje de funcionar. Esto se hace moviendo
el control del termostato en sentido contrario al de
las agujas del reloj hasta el ajuste Baja que es el
menor.
3. El control se mantendrá ahora dentro del nivel
precalibrado, determinando el arranque y detención
(ON y OFF) del calefactor.
NOTA: Para iniciar la operación del calefactor, asegúrese
de que el control del termostato se gire completamente
en el sentido de las agujas del reloj en la posición más
Alta.
NOTA: Es normal que el calefactor se encienda y apague
intermitentemente mientras mantiene la temperatura
seleccionada. Para evitar que la unidad se encienda y
apague, debe aumentar el ajuste del termostato.
PRECAUCIÓN: LA REJILLA FRONTAL SE CALIENTA
CUANDO LA UNIDAD ESTÁ EN FUNCIONAMIENTO.
Para reducir el riesgo de incendios, descargas eléctricas y
lesiones personales al utilizar electrodomésticos, siga siempre
las precauciones básicas de seguridad, incluyendo las que se
mencionan a continuación:
1.
Lea todas las instrucciones antes de usar este calefactor.
2. El calentador se calienta al usarlo. Para evitar
quemaduras, NO toque las superficies calientes con la
piel. Si existen, utilice las manijas para mover la
unidad. Mantenga los materiales combustibles, como
muebles, almohadones, sábanas, papeles, ropa y
cortinas a por lo menos 3 pies (0,9m) de la parte
delantera del calefactor y manténgalos alejados de los
costados y de la parte de atrás.
3. Debe tener mucho cuidado cuando el calefactor es
utilizado por, o cerca de niños o inválidos, y siempre
que se deje el calefactor prendido y desatendido.
4. Siempre desenchufe el calefactor cuando no lo utilice.
5. NO utilice el calefactor si el cable o el enchufe están
dañados o luego de una falla, se haya caído o haya
sufrido cualquier tipo de daño. Deseche el calefactor o
devuélvalo al centro de servicio autorizado para su
revisión y/o reparación.
6. NO utilizar en el exterior.
7. Este calefactor no está diseñado para ser utilizado en
baños, lavaderos y zonas similares de interiores.
NUNCA coloque el calefactor donde pueda caerse
dentro de una bañera u otro recipiente con agua.
8. No coloque el cable debajo de la alfombra. No cubra el
cable con alfombras, tapetes o artículos similares. No
pase el cable por debajo de muebles o
electrodomésticos. Coloque el cable lejos del área de
tráfico y donde no se tropiece con él.
9. Para desconectarlo, gire el control a la posición OFF,
luego quite el enchufe del tomacorriente.
10. No inserte ni permita que objetos extraños penetren
en la ventilación o salida de aire ya que esto puede
causar un choque eléctrico o incendio, o dañar el
calefactor.
11. Para evitar un posible incendio, no bloquee las
entradas de aire o escape de ninguna manera. No lo
use en superficies blandas, como una cama, donde las
aberturas se pueden bloquear.
12. Un calefactor tiene partes calientes y que pueden
producir chispas en su interior. NO lo utilice en áreas
donde se utiliza o se guarda gasolina, pintura o
líquidos inflamables.
13. Utilice este calefactor sólo como se describe en este
manual. Cualquier otro uso no recomendado por el
fabricante puede provocar incendios, descargas
eléctricas o lesiones a personas.
14. Siempre conecte el calefactor directamente a un
tomacorriente de pared. Nunca lo use con un cable de
extensión o con un tomacorriente múltiple.
15. Al desenchufarlo, asegúrese de tirar del enchufe y no
del cable.
16. Si el calefactor no funciona, vea las instrucciones
específicas del apagado automático de seguridad.
17. NO intente reparar o ajustar ninguna función eléctrica
o mecánica de esta unidad. El hacerlo invalidará la
garantía. La unidad no contiene partes reparables por
el usuario. Toda reparación debe ser realizada
únicamente por personal calificado.
18. Deje de usarlo si el cable o el enchufe se calienta. Se
recomienda que reemplace el tomacorriente si el
enchufe o el tomacorriente se calienta.
19. El calefactor no se debe localizar inmediatamente
debajo de un tomacorriente. No use este calefactor en
áreas cercanas a un baño, una ducha o una piscina.
CONSERVE ESTAS
INSTRUCCIONES
LIMPIEZA Y MANTENIMIENTO
SI SU CALEFACTOR NO FUNCIONA
If you have any questions regarding your product or
would like to learn more about other Holmes®products,
please contact our Consumer Service Department at
1-800-546-5637 or visit our website at
www.holmesproducts.com.
Figura 1
A. Manija de
Transporte (no
se muestra)
B. Control de Modo
C. Luz de
Encendido
solo para la HFH110
A
C
B
Figura 2
A. Control del
Thermostato
B. Manija de
Transporte (no se
muestra)
C. Control de Modo
D. Luz de Encendido
solo para la HFH111 &
HFH111T
A
C
D
B
ESTE PRODUCTO TIENE UN ENCHUFE POLARIZADO (una hoja es más
ancha que la otra). A fin de disminuir el riesgo de descarga eléctrica,
este enchufe está diseñado para insertarse en un tomacorriente
polarizado en un solo sentido. Si el enchufe no entra completamente en
el tomacorriente, inviértalo. Si aun así no entra, llame a un electricista
calificado para instalar un tomacorriente apropiado.
NO MODIFIQUE EL ENCHUFE NI ANULE ESTA FUNCION DE SEGURIDAD
DE NINGUNA MANERA.
HFH110/111/111T/WF110_12ESM1.indd 2 11/17/11 3:39 PM