HOMCOM 820-260V80 Datasheet

IN221000594V02_US
USING INSTRUCTION
Electric oil filled heater
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
820-260V80

READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR
MAINTAIN THE PRODUCT DESCRIBED
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION
FAILURE TO COMPLY WITH INSTRUCTION COULD RESULT IN PERSONAL INJURY
AND/OR PROPERTY DAMAGE
RETAIN INSTRUCTIONS FOR FUTURE REDERENCE
IMPORTANT INSTRUCTIONS
When using this appliance, basic precautions should always be followed to reduce
the risk of fire, electric shock and injury to persons, including the following:
CAUTION- High temperature, keep electrical cords, drapery, and other furnishings at least
3 feet (0.9m) from the front of the heater and away from the side and rear.
1.Before using this heater, read and follow all instructions in this manual carefully.
2.Do not cover the heater to prevent overheating.
3.Do not place the heater directly below an electrical outlet or socket.
4.Keep the heater away from humid environments, such as bathrooms. Do not immerse
the appliance in water or let liquid enter the body –this is an electrical hazard. Never use
this appliance near flammable or explosive materials.
5.Never use this appliance if the power cord is damaged. It must be replaced by the
manufacturer, its service agent or a similarly qualified professional.
6.The heater should be filled with a precise amount of professional HTF. Opening or
repairing the fins can only be done by the manufacturer or service personnel. If there is an
oil leak, it must be fixed by the manufacturer or service personnel.
7.When throwing away your heater, check local regulations on how to safely dispose of
the oil inside the heater.
8.Ensure the heater is placed on a smooth and even surface. Do not tilt or turn when in
use.
9.Do not place clothes, towels or other items directly on the heater –this is a safety hazard
that can cause overheating.
10. After use or when left unattended, turn off and unplug the appliance. When
unplugging, grasp the plug and not the wire to avoid any damages.
11.Before cleaning, turn off the appliance and wait for it to cool.
12.When in use, keep the power cord away from the heater’s body.
13. If, for any reason, the appliance does not work, turn off and unplug the appliance
immediately. Contact the manufacturer, its service agent or similarly qualified personnel
for inspection, repairs or replacements.
14.Do not use other electric heaters or electrical appliances in the same outlet or circuit -
this can cause a circuit overload or fire.
15. Do not use extension cords with this appliance.
2

16.Prohibited the use of automatic power program, timer or any other device to use the
heater.
17.Do not put hands, sticks and other objects inserted into the apertures of the heater, to
prevent accidents.
18.When using the heater, in order to avoid burns, do not let bare skin in direct contact
with electric heating The surface. Be sure to take advantage of when you need to move in
front of the handle.
19.May not have towels, clothing, bed sheets, bedding, curtains and other combustible
materials within the heater around 1 meter Products, and should be kept away after
thermal deformation or discoloration of furniture and other items.
20.There shall be no obstructions or unstable hanging objects within 1 meter from the top
of the heater.
21.Children must be supervised to ensure that they do not touch or play with the
appliance.
22. When using the heater, keep doors and windows shut to get the maximum heating
effect.
23.Do not use the heater outdoors.
24.Keep the product specification safe –do not discard it.
PRODUCT CHARACTERISTICS
◆The company manufactured oil heater is a tubular element of heat, high efficiency
permanent oil as the medium through the heat sink to dissipate heat, the use of air circula-
tion to increase room temperature.
◆Electric oil heater easy to use, safe, beautiful, quiet operation, no electromagnetic inter-
ference and other characteristics, suitable for scientific research, hospitals, hotels, martial
arts room, bedroom and other places, in the cold season to make your home or office
more warm and comfortable!
3

Product structure
Figure 2: Castor plate installation diagramme
Figure 1 Product Structure
INSTRUCTIONS FOR USE
1.INSTALLATION METHOD:
Remove the heater and all parts from the packaging box.
(1) Place the heater upside down, then place the castors onto the bottom using the wing
nuts and U-screw (fig. 2).
(2) Place the heater upright, so it is in the correct position.
4
BUTTONS
CASTORS

2. What to check before using:
(1) Ensure the power cord is not damaged.
(2) Ensure the power source matches the electrical requirements stated on the
heaternameplate. Also make sure that it has safety grounding - if not, the outlet must be
replaced.
3.INSTRUCTIONS
POWER:
1. Plug in the power plug, the on/standby key will be high light. Touch the key to start, if no
other operations, the default is high gear mode (the default temperature is 25℃), the mode
key become high light, the display window shows "3", 3 seconds later the display window
shows the setting temperature(the default temperature is 25℃).
2. Touch the key again and the product enters the standby state.
3.The heater can remember the operation state without power off (the timing function is
not memorized).
MODE:
1.Touch this key to switch the machine heating mode, the switching order is high, medium,
low, Eco, high and cycles, the display window displays "3-2-1-Eco-3….” and cycles.
2. When setting the mode, the mode key is highlighted, the display window shows the
current set gear. Three seconds later after the heating mode is set, the display window will
change to indicate the setting temperature ( Default Temperature is 25℃).
3. When the heater is in the three modes of high, medium and low, the temperature can be
set in the range of 15-35℃. The heater will control the on-off of the current setting gear of
the heating pipe according to the setting temperature and the temperature of the NTC
probe.
Figure 3 a schematic view of the control panel
5
POWER

4. When the heater is in eco mode, the temperature can be set within the range of 15-35
℃. The heater will intelligently control the on-off of the heating pipe according to the setting
temperature and NTC probe temperature. And the setting temperature will automatically
decrease by 1℃every hour. It can only be reduced by 5℃and It can only be reduced to
15℃.
TIMER:
1.Touch this key to enter the timing shutdown setting, and this key become highlight, and
the time of shut down is displayed on the display window.
2.Adjust the time of shut down by touch the increase or decrease key, and confirm auto-
matically after 5 seconds without operation or touch the timer key directly to confirm (the
maximum setting is 24 hours, and 0 hours is no timer function).
3.No matter what heating mode the machine is in, it can be set to shut down at a fixed
time.
4.Within 3 seconds after timing confirmation, the display window shows the time of shut-
down time, and after 3 seconds, it will show the setting temperature.
TEMPERATURE:
1.Touch the temperature key, activate the increase and decrease key to adjust the control
temperature, the temperature key become highlight, the control temperature is displayed
on the display window.
2.The default control temperature is 25℃. Set the temperature by touch the increase or
decrease key, and automatically confirm after 5 seconds without operation or touch the
temperature key directly to confirm (the control temperature setting range is 15-35℃).
3.Touch and hold on the temperature key 5 seconds, and the Celsius mode (point + c) is
converted to Fahrenheit mode (point + F). When the machine is in Fahrenheit mode, touch
and hold on the temperature key for 5 seconds to switch back to Fahrenheit mode.
4.In Fahrenheit mode, the default control temperature is 77°F and the setting range is 59°F
-95°F.
5.The Celsius and Fahrenheit modes have a memory function, it can still remember the
last pattern after a complete power outage.
INCREASE / DECREASE:
1.When there is no timing setting or temperature setting, the two corresponding lights are
low light and there is no response by touch this key.
2.When making timing setting or temperature setting, the two keys are active and become
highlight.
3.Before setting the control temperature, you must touch the temperature key first.
DUMPING FUNCTION:
1. When the angle between the machine dumping and the horizontal position is less than
40 ±5 degrees, the display window flashes and prompts "Eo", and all outputs are closed.
2.When the angle between the machine centralization and the horizontal position is more
than 50 ±5 degrees, the working state before dumping will be restored.
6

ANTI-FROST FUNCTION:
1.In the standby state, the mid-range heating is automatically turned on when the NTC
temperature is lower than 5℃(41°F), and when the NTC temperature is higher than 7℃
(45°F), the heating is stopped and returned to the standby state.
2.When the frost protection function is turned on, the ON/STANDBY key become highlight
and flashes at a frequency of 2 seconds per time, and the display window flashes “7℃(or
45°F)”at a frequency of 2 seconds per time.
SUPPLEMENTARY EXPLANATION:
1.If the display window is flashing prompt "EH" or "EL", it need to be repaired by power
outage.
CLEANING AND MAINTENANCE
1. Avoid bruised or scratched heater, so as not to damage the surface coating and rust.
2. After a soft clean cloth is placed in the box collection when unused for long periods, with
the heater.
7
If you have any questions, please contact our customer care center.
Our contact details are below:
001-877-644-9366
[e-mail]
Imported by Aosom LLC
27150 SW Kinsman Rd Wilsonville, OR 97070 USA
MADE IN CHINA