HOMCOM 831-408 User manual

ASSEMBLY INSTRUCTION
INcrb109_US
READ AND SAVE THIS INSTRUCTION FOR FUTURE USE
831-408_831-409

B1 A1
C1D1
F1 E6
H1 G2
Power Adapter Power outlet
Matress Retainer
Bracket
Leg
Spring pin remote control
Input voltage 100-240 V
Input AC frequency 50/60 Hz
Output voltage 29 V
Output current 4A
Output power 116 W
Average active efficiency 85 %
Efficiency at low load (10 %) 76.58-72.23 %
No-load power consumption 0.14-0.3 W
PART
LIST

01
02
A
B
C
D
1.Open the box, use scissors to cut the tape ，check all accessories
2.Make sure the input power cord and outlet is properly connected

03
04
E
F
3.Turn the legs in aclockwise direction into holes on the bed
frame, fasten the 6 legs into the bed
4.Carefully rotate the base frame so the top side is facing upward. Be
careful not to rest the frame on one side, the weight may damage the legs.
Insert the two ends of the bracket into the bed

H H
F
M ZG
F
FLAT
05
06
A A A A A A
A A A
head up
foot up
flat
saved position
head down
foot down
zero-gravity position
G
H
5.Insert the spring pin from the bottom
6.Place batteries into the remote control (3 x AAA batteries)

06
H
H
F
F
FLAT
M
ZG
Symbol Function
Press this button and raise the head of the bed
Press this button and lower the head of the bed
Press this button and raise the foot of the bed
Press this button and lower the foot of the bed
Press “FLAT”button to return bed to the flat
position
Press and keep 3S，the back light on the remote
will will flash 3 times, then, it will remember
current position
Press head down and foot back button together and keep
3S, the back light on the remote will will flash 3 times, the
current position will be treated as ZG. Press ZG,it will work
as set position
Attention:
1、Be sure to connect the plug correctly as per the direction and connect the power before using
2、Close supervision is necessary whenthis furnishing is used by or near children, invalids or disabled
persons
3、Please do not plug or unplug any connecting wire when the power is connected, which may cause
operation function failure.If this happens, cut off the main power supply(Disconnect any end of the
connection of part B in step 2), it can be restored after being reconnected for about 30S;
4、Before first using, the remote should be paired with the control box. The specific methods are as
follows:
A. Pair method: after the control box is disconnected from the power supply for 5S (disconnect either
end of the connection of Part B in Step 2), reconnect the power supply,Control box enters pairing state
B. Pairing duration: The pairing button flashes for 15 seconds
C. Pairing action: During this period, hold the head lift button and foot lift button of the remote for 3S
D.Successful matching performance: backlight flash 3 times, control box beep 1 time.If any key is not
pressed within 15S of the pairing key flashing, the indicator light of the control box will stop flashing. The
original pairing of the hand controller will not be emptied, and the indicator light of the control box will
always be on
E. After the pairing is successful, the operation button will start the corresponding function
5、To unpair a remote, press HEAD DOWN and FOOT DOWN button together for 3S, the backlight of
the remote flashes 3 times, the buzzer sounds, and the pairing is cleared
6、When the remote control presses multiple keys at the same time, the system will recognize them as
invalid keys and will not respond.Except for special combination keys
7、It is not recommended to operate multiple motors at the same time, except for special functions
8、Please replace the battery of the remote in time. Remove the battery when it is not used for a long
time
05