Home Styles 20 05001 0306 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Drill (8 volts or less), 3/8” Drill Bit
20 05001 0306
Hutch
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.
Top
1 pc.
F.
Back Stretcher
1 pc.
G.
Back Stretcher
1 pc.
I.
Fixed Shelf
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
H.
Front Stretcher
1 pc.
J.
Shelf
1 pc.
D.
Back Panel
2 pcs.
E.
Back Upright
1 pc.
K.
Door
1 pc.
L.
Door
1 pc.
Cam Lock
14 pcs. (+2 extra)
Cam Lock Screw
14 pcs. (+1 extra)
M4x13
Wood Screw for Bracket
8 pcs. (+1 extra)
M3.5x16
Wood Screw for Back Panel
8 pcs. (+1 extra)
Adjustable Pin
4 pcs. (+1 extra)
M4x25
Machine Screw
2 pcs.
Knob
2 pcs.
Hutch
Bracket
2 pcs.

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
A
B
C
STEP 1
Insert Cam Lock Screws into pre-drilled holes
in Top (A) and Side Panels (B), (C),
then tighten. (See Figure 1)
F
G
D
E
D
B
Figure 2Figure 1
STEP 2
Attach Back Stretcher (G) to Side Panel (B)
with Cam Lock. (See Figure 2)
Attach Back Upright (E) to Back Stretcher (G).
Slide Back Panels (D) into position.
Attach Back Stretcher (F) to unit with Cam Lock.
Cam Lock Screw
Cam Lock
Cam Lock Screw
Cam Lock

Assembly Instructions 3/6
STEP 5
Attach Side Panel (C) to unit
with Cam Locks.
STEP 3
Attach Fixed Shelf (I) to unit with Cam Locks.
H
I
STEP 4
Attach Front Stretcher (H) to unit with Cam Lock.
C
Cam Lock
Cam Lock
Cam Lock
Cam Lock

Assembly Instructions 4/6
STEP 7
Attach Top (A) to unit with Cam Locks.
Figure 4
Figure 3
STEP 6
Insert Adjustable Pins into side panels
at desired level.
Place Shelf (J) into position.
Attach Doors (K) and (L) to unit by
sliding door hinges into side panel hinges.
(See Figure 3)
Attach Knobs to Doors (K) and (L)
with Machine Screws.
(See Figure 4)
A
Cam Lock
J
K
L
Adjustable Pin
Machine Screw Knob

Assembly Instructions 5/6
STEP 8
Insert Wood Screws for Back Panel
into pre-drilled holes in unit.
STEP 9
Attach Hutch to Buffet with Brackets by inserting
Wood Screws for Bracket into pre-drilled holes.
(See Figure 5)
Figure 5
Wood Screw
for Bracket
Bracket
Wood Screw
for Back Panel

Drill 3/8” hole in wall
Top of unit
Assembly Instructions 6/6
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
STEP 10
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 6)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Figure 6
Hardware List
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319