Home Styles 20 05427 0692 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Carton 20 05427 0691 is also needed for assembly.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
O.
Door
1 pc.
F.
Foot
4 pcs.
P.
Door
1 pc.
I.
Back Panel
2 pcs.
K.
Back Panel
2 pcs.
J.
Upright
1 pc.
L.
Upright
1 pc.
M4x19
Machine Screw
2 pcs.
Adjustable Pin
16 pcs. (+1 extra)
M.
Rail
1 pc.
N.
Rail
4 pcs.
20 05427 0692
Pantry
Knob
6 pcs.
M3x14
Wood Screw for Magnet
4 pcs. (+1 extra)
M3x15
Wood Screw
4 pcs. (+1 extra)
M3.5x38
Wood Screw (long)
2 pcs. (+1 extra)
Magnet
2 pcs.
Q.
Door
1 pc.
R.
Door
1 pc.
G.
Side Panel
1 pc.
H.
Side Panel
1 pc.
M4x32
Machine Screw (long)
4 pcs.

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Lock
Lock
STEP 1
Attach Rail (N) to Side Panel (B),
then flip Lock. (See Figures 1 and 2)
Slide Back Panel (I) into position.
Attach Upright (J) to unit.
Slide Back Panel (I) into position.
Attach Rail (N) to unit, then flip Lock.
STEP 2
Attach Magnet to Rail (M)
with Wood Screws for Magnet
into pre-drilled holes. (See Figure 3)
Attach Rail (M) to unit
with Wood Screw (long).
Attach Side Panel (C) to unit,
then flip Locks.
Insert Wood Screw (long)
into pre-drilled hole in unit, then tighten.
Figure 1
Figure 3
Figure 2
Magnet
Wood Screw for Magnet
Wood Screw (long)
B
C
I
J
M
N
I
N

Assembly Instructions 3/7
STEP 3
Place Base (E) upside down on a soft cloth.
Attach Feet (F) to Base (E).
Lock
STEP 4
Turn over base unit to its upright position.
Attach unit from Step 2 to base unit,
then flip Locks.
Attach Middle Panel (D) to unit, then flip Locks.
STEP 5
Place Top (A) upside down on a soft cloth.
Attach Magnet to Top (A) with Wood Screws for Magnet
into pre-drilled holes.
Wood Screw for Magnet
Magnet
D
F
F
F
F
E

Assembly Instructions 4/7
Lock
Lock
Adjustable Pin
STEP 6
Attach Rail (N) to Side Panel (G),
then flip Lock.
Slide Back Panel (K) into position.
Attach Upright (L) to unit.
Slide Back Panel (K) into position.
Attach Rail (N) to unit,
then flip Lock.
Attach Side Panel (H) to unit,
then flip Locks.
STEP 7
Attach unit from Step 5 to
unit from Step 4, then flip Locks.
Insert Adjustable Pins into
side panels at desired level.
(See Figure 4)
Figure 4
G
H
L
K
K
N
N

Part List
Assembly Instructions 5/7
T1.
Drawer Front
1 pc.
T2.
Drawer Back
1 pc.
T3.
Drawer Side
1 pc.
T4.
Drawer Side
1 pc.
T5.
Drawer Bottom
1 pc.
Drawer (T)
STEP 8
Attach Drawer Sides (T3) and (T4) to
Drawer Back (T2), then flip Locks.
(See Figures 5 and 6)
T3
STEP 10
Attach Knobs with Machine Screws.
T5
Lock
T1
STEP 9
Slide Drawer Bottom (T5) into groove.
Attach Drawer Front (T1) to unit, then flip Locks.
Machine Screw
Knob
T2
T4
Lock
Figure 5 Figure 6

Assembly Instructions 6/7
STEP 11
Place Shelves (S) into position.
Attach Doors (O), (P), (Q) and (R)
to unit by sliding door hinges into
side panel hinges. (See Figure 7)
Attach Knobs to Doors (O), (P), (Q) and (R)
with Machine Screws (long).
Attach Top (A) to unit, then flip Locks.
Slide Drawer (T) into position.
Figure 7
Figure 8
STEP 12
Level unit by adjusting the adjustable levelers
on bottom of unit. (See Figure 8)
Insert Wood Screws into pre-drilled holes
in unit, then tighten.
Note: Unit must be level before
tightening these screws.
Knob
Machine Screw (long)
Wood Screw
A
QR
S
S
S
S
O
P
T

Assembly Instructions 7/7
Hardware List
STEP 13
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 9
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Wood Screw
Wall Screw Pre-drilled hole
at top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319