Home Styles 4514-95 User manual

4514-95
Kitchen Cart
A.
Top
1 pc.
I.
Back Rail
1 pc.
M.
Rack Side
1 pc.
N.
Rack Side
1 pc.
P.
Rack Bar
1 pc.
O.
Rack Base
1 pc.
W.
Base
1 pc.
K.
Arm
2 pcs.
L.
Towel Bar
1 pc.
Q.
Shelf
4 pcs.
T.
Drawer
2 pcs.
J.
Front Rail
1.pc
Refer to later page(s) of these
instructions for drawer assembly.
H.
Back Rail
1 pc.
X.
Front Rail
1 pc.
Part List
Tool(s) required for assembly: Phillips screwdriver
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
C.
Side Panel
1 pc.
F.
Back Panel
3 pcs.
E.
Middle Panel
1 pc.
G.
Back Upright
2 pcs.
B.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
R.
Door
1 pc.
S.
Door
1 pc.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Part List

Assembly Instructions 2/9
Hardware List
09
Machine Screw
8 pcs.
08
Handle
4 pcs.
07
Wood Screw for Magnet
4 pcs. (+1 extra)
12
Flat Head Screw
3 pcs. (+1 extra)
11
Wood Screw (short)
20 pcs. (+1 extra)
Hex Wrench
1 pc.
05
Head Cap Bolt for Caster
16 pcs. (+1 extra)
01
Head Cap Bolt
4 pcs. (+1 extra)
02
Head Cap Bolt (long)
4 pcs. (+1 extra)
06
Magnet
2 pcs.
03
Locking Caster
2 pcs.
04
Non-Locking Caster
2 pcs.
Small
Hex Wrench
1 pc.
10
Wood Screw (long)
24 pcs. (+1 extra)
13
Adjustable Pin
16pcs. (+1 extra)

Assembly Instructions 3/9
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 2
Attach unit to Side Panel (C) with 2 pcs. of .01
01
01
STEP 3
Attach Arms (K) to Side Panel (B) with 2 pcs. of .01
K
B
K
C
STEP 1
Assemble Rack Sides (M), (N), Rack Base (O) and Rack Bar (P).
Note: Spice Rack and Towel Bar are interchangeable and may be installed on either side
of the unit.
P
O
M
N

Assembly Instructions 4/9
Figure 1 Figure 2
STEP 4
Attach Back Rail (H)
to Side Panel (C),
then flip Locks.
(See Figures 1 and 2)
Attach Back Uprights (G)
to unit.
Slide Back Panels (F)
into position.
Attach Back Rail (I)
to unit, then flip Lock.
Attach Side Panel (B)
to unit, then flip Locks.
Figure 3
02
Lock
Lock
F
CF
G
F
H
G
B
I
Arrow label at front
W
STEP 5
Attach Base (W) to unit with
4 pcs. of . (See Figure 3)02
Then flip Locks.
Note: Arrow label indicates front of Base (W).

Assembly Instructions 5/9
Figure 4
STEP 6
Attach 2 pcs. of and 2 pcs. of03 04
to unit with 16 pcs. of .05
Attach at front.03
(See Figure 4)
Note: Arrow label indicates front of unit.
07
06
STEP 7
Attach 2 pcs. of to Front Rail (X)06
by inserting 4 pcs. of into pre-drilled holes,07
then tighten. (See Figure 5)
Figure 5
05
04
03
X
Arrow label at front