Home Styles 20 05520 0911 User manual

Part List
Hardware List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16” Drill Bit, 3/8” Drill Bit
Carton 20 05520 0912 is also needed for assembly.
20 05520 0911
IMPORTANT
Storage Island
Cam Lock Screw
26 pcs. (+2 extra)
M4x16
Machine Screw
8 pcs.
M3 x.5 32
Wood Screw
4 pcs. (+1 extra)
D.
Back Panel
1 pc.
A.
Top
1 pc.
E.
Bottom
1 pc.
B.
Rail
2 pcs.
C.
Rail
3 pcs.
F.
Plinth
2 pcs.
Small Hex Wrench
1 pc.
Cam Lock
26 pcs. (+6 extra)
Handle
4 pcs.
Adjustable Pin
12 pcs. (+1 extra)
Flat Washer
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
M6x32
Head Cap Bolt
12 pcs. (+1 extra)
Hex Wrench
1 pc.

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A),
Bottom (E), Plinths (F), Side Panels (G) and (H), then tighten.
(See Figure 1)
H
Cam Lock Screw
Cam Lock Screw
A
F
G
E
F
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Figure 1

Assembly Instructions 3/8
STEP 3
Attach unit form Step 2 to
Side Panel (H) with Flat Washers,
Spring Washers, Head Cap Bolts
and Cam Locks, tightening bolts
only halfway. (See Figure 3)
Attach Rails (B) and (C) to
unit with Cam Locks and
Wood Screws.
STEP 2
Attach Back Panel (D) to
Bottom (E) with Cam Locks.
(See Figure 2)
Attach Plinths (F) to unit with
Cam Locks.
F
D
B
F
C
H
C
C
Flat Washer
Cam Lock
Wood Screw
Head Cap Bolt
Spring Washer
Cam Lock
Figure 2
Figure 3
E
B

Assembly Instructions 4/8
G
STEP 4
Attach Side Panel (G) to unit with
Cam Locks, Flat Washers, Spring
Washers, Head Cap Bolts and
Wood Screws, tightening bolts
only halfway.
Turn unit to it’s
upright position. Flat Washer
Wood Screw
Head Cap Bolt
Spring Washer
Cam Lock
STEP 5
Insert Adjustable Pins
into side panels at
desired level.
Place Shelves (I) into
position.
Adjustable Pin
I
I
I

Assembly Instructions 5/8
Part List
Drawer (J)
J1.
Drawer Front
1 pc.
J2.
Drawer Back
1 pc.
J3.
Drawer Side
1 pc.
J4.
Drawer Side
1 pc.
J5.
Drawer Bottom
1 pc.
Figure 5Figure 4
J4
J2
J3
Lock
J1
J5
Handle
Machine Screw Lock
STEP 6
Attach Drawer Sides (J3) and (J4) to
Drawer Back (J2), then flip Locks.
(See Figures 4 and 5)
STEP 7
Slide Drawer Bottom (J5) into groove.
Attach Drawer Front (J1) to unit,
then flip Locks.
STEP 8
Attach Handle with Machine Screw.

Assembly Instructions 6/8
Part List
Drawer (K)
K4
K2 K3
Lock
K1
K5
Handle
Machine Screw
Lock
STEP 9
Attach Drawer Sides (K3) and (K4) to
Drawer Back (K2), then flip Locks.
STEP 11
Attach Handle with Machine Screw.
K1.
Drawer Front
3 pcs.
K2.
Drawer Back
3 pcs.
K3.
Drawer Side
3 pcs.
K4.
Drawer Side
3 pcs.
K5.
Drawer Bottom
3 pcs.
STEP 10
Slide Drawer Bottom (K5) into groove.
Attach Drawer Front (K1) to unit,
then flip Locks.

Assembly Instructions 7/8
STEP 13
Level unit by adjusting the adjustable
levelers on bottom of unit.
(See Figure 6)
Note: Unit must be level to work
properly.
Slide Drawers (J) and (K) into
position.
K
J
K
K
Figure 6
A
STEP 12
Attach Top (A) to unit with Cam Locks
Flat Washer, Spring Washer and
Head Cap Bolts, tightening bolts
only halfway.
Flat Washer
Cam Lock
Head Cap Bolt
Spring Washer

Assembly Instructions 8/8
Hardware List
Anchor
1 pc. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3x16
Wood Screw
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
STEP 14
Drill a 3/16” hole 1/2” deep 1” below top
of unit in middle of side panel that is
against a wall.
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
3/16” hole drilled in side panel.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at drilled hole in
side panel of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Drill 3/8” hole in wall
Side Panel of unit
Per regulatory requirements, a Tip-over Restraint is included. Follow Step 14 to install it.
Figure 7
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
3/16” hole in
side panel of unit
Tie end
Lock end
Bracket
on side panel
of unit
Tip-over
Restraint

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319