Home Styles 20 05170 0049 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
20 05170 0049
Hall Tree
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
F.
Door
1 pc.
H.
Foot
4 pcs.
N.
Back Upright
1 pc.
K.
Side Panel
1 pc.
O.
Back Rail
1 pc.
A.
Seat
1 pc.
B.
Base
1 pc.
I.
Top
1 pc.
J.
Shelf
1 pc.
R.
Back Panel
2 pcs.
Q.
Back Panel
1 pc.
P.
Back Rail
1 pc.
L.
Side Panel
1 pc.
G.
Door
1 pc.
M.
Divider
1 pc.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Cam Lock Screw
14 pcs. (+1 extra)
Cam Lock
14 pcs. (+2 extra)
Knob
4 pcs.
M4x22
Machine Screw
4 pcs.
M3x14
Wood Screw
for Hook
8 pcs. (+1 extra)
Hook
4 pcs.
M6x45
Head Cap Bolt
4 pcs. (+1 extra)
E.
Back Panel
1 pc.
Magnet
1 pc.
M3x14
Wood Screw
for Magnet
2 pcs. (+1 extra)

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in future.
Figure 1
Figure 2
STEP 1
Attach Side Panels (C) and (D) to Back Panel (E), then flip the locks. (See Figures 1 and 2)
E
C
D
Lock
B
H
H
H
HSTEP 2
Attach Base (B) to unit, then flip the locks.
Insert Feet (H) into pre-drilled
holes of Base (B), then tighten.
Lock

Figure 3
Figure 4
STEP 3
Turn unit to its’ upright position.
Attach Doors (F) and (G) to unit by sliding door hinges into side panel hinges.
(See Figure 3)
Attach Knobs to Doors (F) and (G) with Machine Screws.
(See Figure 4)
Figure 5
STEP 4
Insert Cam Lock Screws into pre-drilled holes of Top (I) and Side Panels (K), (L).
(See Figure 5)
I
K
L
Cam Lock Screw
F
G
Machine Screw
Knob
Assembly Instructions 3/7

STEP 5
Attach Hooks to Back Rail (O) with Wood Screws for Hook.
(See Figure 6)
Wood Screw
for Hook
Hook
Figure 6
O
STEP 6
Attach Shelf (J) and Back Rails (O), (P)
to Side Panel (K) with Cam Locks.
(See Figure 7)
K
JO
P
Cam Lock
Figure 7
N
R
R
Q
STEP 7
Slide Back Panel (R) and Back Upright (N) into position.
Slide Back Panels (R) and (Q) into position.
Assembly Instructions 4/7

Figure 8 Figure 9
STEP 8
Attach Side Panel (L) to unit with Cam Locks.
L
Cam Lock
STEP 9
Attach Seat (A) to unit with Head Cap Bolts.
(See Figure 8)
Attach Magnet to unit with Wood Screws for
Magnet into pre-drilled holes. (See Figure 9)
Assembly Instructions 5/7
Wood Screw
for Magnet
Magnet
A
Head Cap Bolt

Figure 10
STEP 10
Turn unit to its’ upright position.
Attach unit to unit from Step 3, then flip the locks.
Lock
STEP 11
Attach Divider (M) to unit.
Attach Top (I) to unit with Cam Locks.
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure 10)
M
I
Assembly Instructions 6/7
Cam Lock

Assembly Instructions 7/7
Hardware List
STEP 12
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 11)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 11
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319