Home Styles HS-5050-102 Quick start guide

IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
88 5050 102
Modern Craftsman
6 Tier Tower
B.
Side Frame
1 Pc.
Hex Wrench
1 Pc.
Small
Hex Wrench
1 Pc.
Head Cap Bolt
16 Pcs.(+1 extra)
Flat Washer
16 Pcs.(+1 extra)
Spring Washer
16 Pcs.(+1 extra)
Tapered Head Cap Bolt
12 Pcs.(+1 extra)
Wood Screw (long)
15 Pcs.(+1 extra)
Wood Screw (short)
4 Pcs.(+1 extra)
Tools recommended for assembly : Level
C.
Side Frame
1 Pc.
D.
Back Frame
1 Pc.
E.
Back Frame
1 Pc.
F.
Back Stretcher
1 Pc.
G.
Back Stretcher
2 Pcs.
H.
Front Stretcher
1 Pc.
I.
Front Stretcher
5 Pcs.
J.
Shelf
5 Pcs.
A.
Top
1 Pc.
Tools required for assembly : Phillips screwdriver

Assembly Instructions 2
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the oor.
STEP 1
Attach Back Frame (D) and Back Frame (E) to Back Stretcher (G) with Tapered Head Cap Bolts.
Attach Back Stretcher (F) and Back Stretcher (G) to unit with Tapered Head Cap Bolts.
(See Figure 1)
STEP 2
Attach Front Stretcher (H) to Side Frame (B) with Tapered Head Cap Bolts.
Attach unit from Step 1, Front Stretchers (I) and Side Frame (C) to unit with Head Cap Bolts,
Spring Washers, Flat Washers and Tapered Head Cap Bolts.
Tighten all Bolts with Hex Wrench. (See Figure 2)
F
D
G
G
E
B
C
H
I
I
I
I
I
Figure 1
Figure 2
/3
Tapered Head Cap Bolt
Tapered Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer

Assembly Instructions 3/3
STEP 3
Turn the unit over to its’ upright position.
Place Top (A) and Shelves (J) into position.
STEP 4
Place Top (A) onto unit with Wood Screws (short).
Attach Shelves (J) to unit with Wood Screws (long).
To level the unit, adjust the adjustable levelers on the
bottom of legs.
(See Figure 3)
Note: Unit must be level to work property.
Figure 3
Wood Screw (short)
Wood Screw (long)
A
A
J
J
J
J
J
J
J
J
J
J

Anchor
1 pc.(+1 extra)
Bracket
1 pc.(+1 extra)
Plastic Belt
1 pc.(+1 extra) Wall Screw
1 pcs. (+1 extra)
HARDWARE LIST
Attention !
For safety reasons, we recommended you strictly follow these
additional instructions to prevent the unit from tipping over.
Wall Bracket
Wall Screw
Plastic Belt
Assembly Instructions
Place the cabinet at desired
location in room.
Drill a ¼ hole in wall at the appropriate”
location.
Insert the Anchor into the wall hole and
attach the Bracket using the wall screw.
Use the Plastic Belt to secure the
hole at the back of unit to the Bracket on
the wall.
Put the tie end of the belt into the loop end
of the belt and pull until tight.
The hole at
the back of cabinet