Home Styles General Line 52195 User manual

Part List
Tool(s) required for assembly: Phillips screwdriver
521 -957
Kitchen Cart
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M6x25
Head Cap Bolt (short)
2 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
16 pcs. (+1 extra)
M3.5x16
Wood Screw (short)
12 pcs. (+1 extra)
Wood Plug
13 pcs. (+1 extra)
Adjustable Pin
4 pcs. (+1 extra)
Refer to later page(s) of these instructions for drawer assembly.
E.
Back Panel
1 pc.
A.
Top
1 pc.
B.
Side Frame
1 pc.
C.
Side Frame
1 pc.
J.
Towel Bar
1 pc.
D.
Front Rail
2 pcs. F.
Divider
1 pc.
G.
Base
1 pc.
H.
Shelf
1 pc.
I.
Drawer
2 pcs.
Caster
2 Locking
2 Non-Locking
4 pcs.
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
M6x35
Head Cap Bolt
1 pcs. (+1 extra)5
M4x25
Machine Screw
4 pcs.
Handle
2 pcs.
Hardware List
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
M4x24
Cam Lock Screw
4 pcs. (+1 extra)
Cam Lock
4 pcs. (+2 extra)

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
E
Head Cap Bolt
B
F
Head Cap Bolt
Figure 1
DSTEP 2
Attach Divider (F) to unit
with Head Cap Bolt,
tightening bolt only halfway.
Attach Front Rail (D) to unit
with Head Cap Bolts,
tightening bolts only halfway.
STEP 1
Attach Back Panel (E) to Side Panel (B)
with Head Cap Bolts tightening bolts,
only halfway. (See Figure 1)

Assembly Instructions 3/7
C
Head Cap Bolt
G
Head Cap Bolt
D
STEP 4
Attach Side Panel (C) to unit with Head Cap Bolts, tightening b ts only halfway.ol
Tighten all Head Cap Bolts used in Steps 1, 2, 3 and 4.
STEP 3
Attach Front Rail (D) to unit with Head Cap Bolts,
tightening bolts only halfway.
Attach Base (G) to unit with Head Cap Bolts, tightening bolts only halfway.

Assembly Instructions 4/7
STEP 5
Turn unit upside down.
Attach Casters to bottom of unit with Locking Casters at front. (See Figure 2)
Figure 2
Non-Locking Caster
Locking Caster

STEP 7
Turn unit over to its
upright position.
Attach Towel Bar (J) to unit with
Head Cap Bolts (short).
Orientate Top (A) so Arrow label
on bottom of Top (A) is at front
of unit, then attach Top (A) to unit
with Cam Locks. (See Figure 4)
J
A
Arrow label at front
Assembly Instructions /57
Cam Lock Screw
STEP 6
Place Top (A) upside down on
a soft cloth.
Insert Cam Lock Screws into
pre-drilled holes in Top (A),
then tighten. (See Figure 3)
A
Arrow label at front
Figure 4
Head Cap Bolt (short)
Cam Lock
Figure 3

Part List
Assembly Instructions /67
STEP 9
Slide Drawer Bottom (I5) into groove.
Attach Drawer Bottom (I5) to unit
with Wood Screws (short).
STEP 10
Attach Handle with Machine Screws.
Drawer (I)
I2.
Drawer Back
2 pcs.
I5.
Drawer Bottom
2 pcs.
I1.
Drawer Front
2 pcs.
I3.
Drawer Side
2 pcs.
I4.
Drawer Side
2 pcs.
STEP 8
Attach Drawer Front (I1) and Drawer
Back (I2) to Drawer Side (I3) with
Wood Screws (long).
Attach Drawer Side (I4) to unit with
Wood Screws (long).
Wood Screw (long)
Bottom
Wood Screw (short)
Machine Screw
Handle
Roller at back
I5
Bottom Bottom
I2
I3
I4
I1
BottomBottom

Assembly Instructions /77
STEP 11
Slide Drawers (I) into position.
Insert Adjustable Pins into
side frames at desired level,
then tighten. (See Figure 5)
Place Shelf (H) into position.
STEP 12
Cover holes with
Wood Plugs.
(See Figure 6)
Wood Plug
Figure 5
Figure 6
Adjustable Pin
I
I
H

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460