Home Styles 5055-69 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Knob
4 pcs.
M4x25
Machine Screw
8 pcs.
Cam Lock Screw
30 pcs. (+1 extra)
Cam Lock
30 pcs. (+4 extra)
M3.5x16
Wood Screw (short)
22 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
8 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
5055-69
Pantry
A.
Top
1 pc.
D.
Side Panel
1 pc.
E.
Side Panel
1 pc.
F.
Front Rail
1 pc.
G.
Front Rail
2 pcs.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
H.
Back Rail
4 pcs.
I.
Back Upright
2 pcs.
J.
Back Panel
4 pcs.
K.
Middle Panel
1 pc.
L.
Base
1 pc.
M.
Shelf
4 pcs.
N.
Door
1 pc.
O.
Door
1 pc.
P.
Door
1 pc.
Q.
Door
1 pc.
Refer to later page(s) of these
instructions for drawer assembly.
R.
Drawer
1 pc.
Handle
2 pcs.
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
The unit must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in
Top (A), Side Panels (B), (C), (D), (E), Top (K) and
Base (L), then tighten. (See Figure 1)
Figure 1
A
L
B
C
D
E
K
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw

Assembly Instructions 3/8
B
C
H
J
J
I
G
F
Figure 2
STEP 3
Attach Front Rails (F)
and (G) to unit with
Cam Locks.
Attach Side Panel (B)
to unit with Cam Locks.
H
STEP 2
Attach Back Rail (H) to
Side Panel (C) with Cam Lock.
(See Figure 2)
Attach Back Upright (I) to
Stretcher (H).
Slide Back Panels (J) into position.
Attach Back Rail (H) to unit
with Cam Lock.
Cam Lock
Cam Lock
Cam Lock

Assembly Instructions 4/8
L
Cam Lock
Figure 3
STEP 4
Attach Base (L) to unit with Cam Locks.
K
P
Q
Cam Lock
Knob
Machine Screw
Figure 4
STEP 5
Turn unit over to its upright position.
Attach Doors (P) and (Q) by sliding
door hinges into side panel hinges.
(See Figure 3)
Attach Knobs to Doors (P) and (Q)
with Machine Screws. (See Figure 4)
Attach Middle Panel (K) to unit
with Cam Locks.

Assembly Instructions 5/8
STEP 6
Attach Back Stretcher (H) to
Side Panel (D) with Cam Lock.
Attach Back Upright (I) to
Stretcher (H).
Slide Back Panels (J) into position.
Attach Back Stretcher (H) to unit
with Cam Lock.
Attach Front Stretcher (G)
to Side Panel (D) with Cam Lock.
Attach Side Panel (E)
to unit with Cam Locks.
G
D
E
H
H
I
J
J
Cam Lock
Cam Lock
STEP 7
Attach unit from Step 6 to unit from Step 5
with Cam Locks.

Assembly Instructions 6/8
R1.
Drawer Front
1 pc.
R2.
Drawer Back
1 pc.
R3.
Drawer Side
1 pc.
R4.
Drawer Side
1 pc.
R5.
Drawer Bottom
1 pc.
Handle
Bottom
Roller at back
Wood Screw (long)
Machine Screw
Part List
STEP 10
Attach Handles with Machine Screws.
STEP 9
Slide Drawer Bottom (R5) into groove.
Attach Drawer Bottom (R5) to unit
with Wood Screws (short).
Drawer (R)
STEP 8
Attach Drawer Front (R1) and
Drawer Back (R2) to Drawer Side (R3)
with Wood Screws (long).
Attach Drawer Side (R4) to unit
with Wood Screws (long).
R5
Wood Screw (short)
R2
R3
R4
R1
Bottom
Bottom

Assembly Instructions 7/8
Figure 5
STEP 12
Level unit by adjusting the adjustable levelers
on bottom of unit. (See Figure 5)
Note: Unit must be level to proceed.
Insert Wood Screws (short) into
pre-drilled holes in unit,
then tighten.
Note: Unit must be level before
tightening these screws.
M
A
N
M
R
STEP 11
Insert Adjustable Pins into side panels at
desired level.
Place Shelves (M) into position.
Slide Drawer (R) into position.
Attach Doors (N) and (O) to unit by sliding
door hinges into side panel hinges.
Attach Knobs to Doors (N) and (O) with
Machine Screws.
Attach Top (A) to unit with Cam Locks.
Machine Screw
Knob
Cam Lock
Wood Screw (short)
M
M
Adjustable Pin
O

Assembly Instructions 8/8
Figure 6
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
STEP 13
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 6)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestylesfurniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319