Home Styles 20 05420 0692 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Carton 20 05420 0691 is also needed for assembly.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
N.
Door
1 pc.
O.
Door
1 pc.
P.
Door
1 pc.
Q.
Door
1 pc.
F.
Side Panel
1 pc.
G.
Side Panel
1 pc.
H.
Back Panel
2 pcs.
J.
Back Panel
2 pcs.
I.
Upright
1 pc.
K.
Upright
1 pc.
M4x25
Machine Screw
6 pcs.
Adjustable Pin
16 pcs. (+1 extra)
M6x32
Head Cap Bolt
4 pcs. (+1 extra)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Flat Washer
4 pcs. (+1 extra)
Spring Washer
4 pcs. (+1 extra)
L.
Rail
1 pc.
M.
Rail
3 pcs.
20 05420 0692
Pantry
Knob
6 pcs.
M3x14
Wood Screw
for Magnet
4 pcs. (+1 extra)
M3x15
Wood Screw
8 pcs. (+1 extra)
M3.5x38
Wood Screw (long)
2 pcs. (+1 extra)
Magnet
2 pcs.

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Lock
STEP 1
Attach Base (E) to Side Panel (B) with
Flat Washers, Spring Washers and
Head Cap Bolts. (See Figure 1)
Slide Back Panel (H) into position.
Attach Upright (I) to unit, then slide
Back Panel (H) into position.
Attach Rail (M) to unit, then flip Locks.
(See Figures 2 and 3)
STEP 2
Attach Magnet to Rail (L) with Wood Screws
into pre-drilled holes. (See Figure 4)
Attach Rail (J) to unit with
Wood Screw (long).
Attach Side Panel (C) to unit with
Flat Washers, Spring Washers and
Head Cap Bolts, then flip Locks.
Insert Wood Screw (long) in
pre-drilled hold in unit, then tighten.
B
Figure 2 Figure 4 Figure 1 Figure 3
C
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
Magnet
Wood Screw
Wood Screw
(long)
E
H
H
IM
L

Assembly Instructions 3/7
Lock
STEP 3
Turn unit to its’ upright position.
Attach Middle Panel (D) to unit,
then flip Locks.
D
F
G
Lock
STEP 4
Attach Rail (M)
to Side Panel (F),
then flip Locks.
Attach Upright (K) to unit.
Slide Back Panels (J) into position.
Attach Rail (M) to unit, then flip Lock.
Attach Side Panel (G) to unit, then flip Locks.
M
M
J
J
K

Assembly Instructions 4/7
Lock
Adjustable Pin
STEP 5
Attach Magnet to Top (A)
with Wood Screws into pre-drilled holes.
Attach Top (A) to unit from Step 4,
then flip Locks.
Magnet
Wood Screw
A
STEP 6
Attach unit from Step 5 to
unit from Step 3, then flip Locks.
Insert Adjustable Pins into
side panels at desired level.
(See Figure 5)
Figure 5

Part List
Assembly Instructions 5/7
S1.
Drawer Front
1 pc.
S2.
Drawer Back
1 pc.
S3.
Drawer Side
1 pc.
S4.
Drawer Side
1 pc.
S5.
Drawer Bottom
1 pc.
Drawer (S)
STEP 7
Attach Drawer Sides (S3) and (S4) to
Drawer Back (S2), then flip Locks.
(See Figures 6 and 7)
S3
STEP 9
Attach Knobs with Machine Screws.
S5
Lock
S1
STEP 8
Slide Drawer Bottom (S5) into groove.
Attach Drawer Front (S1) to unit, then flip Locks.
Machine Screw
Knob
S2
S4
Lock
Figure 6 Figure 7

Assembly Instructions 6/7
STEP 10
Place Shelves (R) into position.
Attach Doors (N), (O), (P) and (Q)
by sliding door hinges into
side panel hinges. (See Figure 8)
Attach Knobs to Doors with Machine Screws.
Slide Drawer (S) into position.
Figure 8
Figure 9
STEP 11
Level unit by adjusting the adjustable levelers
on bottom of unit. (See Figure 9)
Insert Wood Screws into pre-drilled holes
in unit, then tighten.
Note: Unit must be level before
tightening these screws.
PQ
Knob
Machine Screw
Wood Screw
N
O
R
R
R
R
S

Assembly Instructions 7/7
Hardware List
STEP 12
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 10)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Figure 10
Wood Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Drill 3/8” hole in wall
Top of unit
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319