Home Styles Monarch 5020-31 User manual

Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
A.
Top
1 pc.
B.
Top
1 pc.
C.
Leaf
1 pc.
E.
Leg
4 pcs.
Wrench
1 pc.
M3.5x 03
Wood Screw
6 pcs. (+1 extra)
Spring Washer
8 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
Spring Washer (small)
12 pcs. (+1 extra)
Flat Washer (small)
12 pcs. (+1 extra)
F.
Slide
2 pcs.
M8x50
Bolt
8 pcs. (+1 extra)
M6x40
Head Cap Bolt
12 pcs. (+1 extra)
Tool(s) required for assembly: Phillips screwdriver, Level
IMPORTANT
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
5020-31
Dining Table
Part List
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hardware List
M3.5x40
Wood Screw
16 pcs. (+1 extra)
D.
Apron
2 pcs.

Assembly Instructions 2/4
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Figure 2
Figure 4
Figure 3
Wood Screw
Figure 1
Head Cap Bolt
Spring Washer (small)
Flat Washer (small)
STEP 2
Attach Tops (A) and (B) by aligning metal pins with holes and pushing
together.
Engage locks by turning lock handles clockwise 1/4 turn. (See Figure 2)
Attach Slides ( ) to unit with Flat Washers (small), Spring Washers (small),F
Head Cap Bolts and Wood Screws. (See Figures 3 and 4)
STEP 1
Place Tops (A) and (B) upside down on a soft cloth.
Remove Slides ( ) from their packing position by removing Head Cap Bolts,F
Spring Washers (small) and Flat Washers (small). (See Figure 1)
Head Cap Bolt
Spring Washer (small)
Flat Washer (small)
F
B
F
A
B
A
F
F

Assembly Instructions 3/4
Figure 5
STEP 3
Attach Legs (E) to unit with Flat Washers, Spring Washers and Bolts. (See Figure 5)
Flat Washer
Spring Washer
Bolt
E
E
E
E

Figure 6
Figure 7
STEP 5
Turn table over to its upright position.
Disengage locks by turning lock handles counter-clockwise.
(See Figure 6)
Pull out both ends of table, then place Leaf (C) in ,table
aligning metal pins with holes.
Push table together then engage locks by turning lock,
handles clockwise 1/4 turn.
Level by adjusting the adjustable levelers on bottom of legs.table
(See Figure 7)
C
Assembly Instructions /44
STEP 4
Place Leaf (C) upside down on a soft cloth.
Attach Aprons (D) to Leaf (C) with
Flat Washers (small), Spring Washers (small),
Head Cap Bolts and Wood Screws (short).
Wood Screw (short)
Head Cap Bolt
Spring Washer (small)
Flat Washer (small)
C
D
D

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460