Home Styles 88 5040 95C User manual

PART LIST
K.
Round Arms
1 pc.
HARDWARE LIST
Head Cap Bolt
16 pcs.(+1 extra)
Machine Screw
for Pull Handle
6 pcs.
Wood Screw
(for Caster)
16 pcs. (+1 extra)
B.
Side Frame L.
.1 pc
C.
Side Frame R.
1 pc.
Pull Handle
3 pcs.
A.
Top
1 pc.
F.
Base Panel
1 pc.
E.
Front Rail
1 pc.
I.
Back Panel
2 pcs.
D.
Upper
Back Stretcher
1 pc.
G.
Lower
Back Stretcher
1 pc.
H.
Middle
Back Stretcher
1 pc.
M.
Adjustable Shelf
1 pc.
J.
Handle Arms
2 pcs.
Wood Plug
6 pcs.(+1 extra)
88 5040 95C
Kitchen Cart
Adjustable Pin
4 pcs.(+1 extra)
Wood Screw 6 x 1”
Long (for Drawer)
8 pcs.(+1 extra)
Caster
2 with brake and
2 without brake
4 pcs.
O1.
Door
1 pc.
O2.
Door
1 pc.
L.
Drawer
(Please refer to the last page(s) of
instructions for step to complete
drawer assembly.)
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools Required For Assembly : Phillips screwdriver
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319

Assembly Instructions 2/4
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to tighten up
the Head Cap Bolts in the future.
STEP 1
STEP 2
Attach Side Frame L (B) to Base
Panel (F) with Head Cap Bolts.
Attach Front Rail (E) and Lower Back Stretcher (G)
to the unit with Head Cap Bolts and tighten.
Attach Middle Back Stretcher (H) to Lower
Back Stretcher (G), then slide Back Panels (I) into place.
Attach the Upper Back Stretcher (D) to the unit with
Head Cap Bolts and tighten.
STEP 3
E
II
H
G
D
F
F
B
Attach Casters to the bottom side of
Base Panel (F) with Wood Screws
(for Caster), putting the Casters with
brakes in front.
C
KJJ
Attach the Side Frame R (C) to the unit with Head Cap Bolts and tighten.
Attach the Handle Arms (J) using Head Cap Bolts from the inside of the side frames and
put the Round Arms (K) into place.
Tighten Head
Cap Bolt with
Hex Wrench.

STEP 4
STEP 5
Attach Doors (O1), (O2) to the unit.
Assemble the Door Pull Handles to the doors with Machine Screws.
Insert the Adjustable Pins into the side frames at the desired level. Slide Adjustable Shelf (M)
and Drawer (L) into place.
Assembly Instructions 3/4
Attach Top (A) to the unit and
tighten the Head Cap Bolts through
Side Frames (B) and (C).
O1
O2
B
C
A
L
M
Top
Assembly
STEP 6
Cover all holes with
Wood Plugs.
See the attached sheet for
drawer assembly instructions.
Door Assembly
using Hinge
Pull Handle
Assembly

(Fig)1
MAKE SURE ROLLER
IS ON THE BACK
L3
L4 L1
(Fig) 1
Line up Side Parts (L3) and (L4) to the
Front Part (L1). Be sure to follow the stickerArrow
on the parts. Using a screw driver,Philips
insert screws into each of the 4 pre-drilled
holes in sides (L3) and (L4), then tighten half way.
Assembly Instructions 4/4
Drawer
L5
Unit Part List
L3.
Side Part(L)
1 pc.
L4.
Side Part(R)
1 pc.
L5.
Bottom Part
1 pc.
(Fig) 2
(Fig) 3
(Fig) 4
Assemble the Pull Handle
with Machine Screw on
the Front Part (L1).
(Fig)2
(Fig)3
(Fig)4
Turn the assembled drawer over and slide the
Bottom Part (L5) into the grooves
on Side Parts (L1), (L3) and (L4). Be sure to push
the Bottom Part (L5) all the way forward so it meets
the Front Part (L1).
Attach the Back Part (L2) to the assembled drawer. Using a
screw driver, insert screws into each of the 4Philips
pre-drilled holes in sides (L3) and (L4), then tighten all
screws.
L5
L3
L1
L4
L2
L2.
Back Part
1 pc.
L1.
Front Part
1 pc.