Home Styles 88 9100 002C User manual

88 9100 002C
Kitchen Cart
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
PART LIST
HARDWARE LIST
A.
Side Panel
1 pc.
B.
Side Panel
1 pc.
H.
Back Panel
3 pcs.
F.
Back Piece
2 pcs.
E2.
Front Piece
1 pc.
E1.
Front Piece
1 pc.
I.
Back Stretcher
1 pc.
J.
Front Stretcher
1 pc.
K.
Front Rail
3 pcs.
G.
Base
1 pc.
R.
Shelf
2 pcs.
L.
Side Rack
1 pc.
M.
Side Rack
1 pc.
O
Brush Chrome Pipes
3 pcs.
D.
Middle Panel
1 pc.
C.
Middle Panel
1 pc.
N.
Base Rack
1 pc.
(For Drawer U&V packed in separate carton
with hardware and assembly instructions.)
T.
Door
1 pc.
S.
Door
1 pc.
V.
KD. Drawer
1 pc.
U.
KD. Drawer
3 pcs.
P.
Handle Arm
2 pcs.
Q.
Round Arm
1 pc.
Tools Required For Assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Hex Wrench
1 pc.
Machine Screw
for Knob
2 pcs.
Wood Screw
for Caster
16 pcs. (+2 extra)
Wood Plug
10 pcs.
(+2 extra)
Caster
two lock
two non-lock
4 pcs.
Adjustable Pin
8 pcs. (+2 extra)
Head Cap Bolt
14 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Knob
2 pcs.

Assembly Instructions 2/3
STEP 1
STEP 2
STEP 3
G
G
K
K
K
C
D
A
Attach four Casters
underneath Base (G)
with Wood Screws.
(See ‘Arrow’ sticker
indicating front side)
Assemble Front Piece (E1),
(E2) and Front Rail (K).
(See figure 1)
Attach the assembled unit
to Middle Panel (C) and (D).
Attach Side Panel (A) to the
side of unit with Head Cap Bolts.
Attach the Back Piece (F), Middle Panel (C)
and Back Piece (F), Middle Panel (D) onto the
Base (G).
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to
tighten up the Head Cap Bolts in the future.
FF
CD
E1
E2
Wood Screw
Wood Screw
Head Cap Bolt
Locking Caster
(On Front)
(Figure 1)

R
R
STEP 4
STEP 7
STEP 8
J
B
I
Insert Adjustable Pins into both
side panels and middle panels
at the desired level.
Place Shelf (R).
HHH
A
M
N
O
LSTEP 5
Attach Side Rack (L) to Side Panel (A) with
Head Cap Bolts.
Attach Brush Chrome Pipes (O) and Base Rack (N)
to the Side Rack (L).
Attach Side Rack (M) to the Side Panel (A),
using Head Cap Bolts.
Head Cap Bolt
Head Cap Bolt
Adjustable Pin
Head Cap Bolt
BQ
P
P
STEP 6
Attach Handle Arm (P) to Side Panel (B)
with Head Cap Bolts.
Slide the Round Arm (Q) into place.
Cover up all holes
with Wood Plugs.
Slide Back Panel (H) into place.
Attach Back and Front
Stretcher (I), (J) to the unit
with Head Cap Bolts.
Attach Side Panel (B) to the other
side of unit with Head Cap Bolts.
Assembly Instructions 3/3

88 9100 002C
Drawer (U)
Assembly Instructions
U3.
Side Part
1 pc. for each
drawer.
U4.
Side Part
1 pc. for each
drawer.
U5.
Base Part
1 pc. for each
drawer.
U2.
Back Part
1 pc. for each
drawer.
U2
U5
U5
U4
U4
U3
U3
U1
U1
Assemble the Pull Handle
with Machine Screw on
the Front Part (U1).
(See the figure 4)
(Figure 2)
(Figure 3)
HARDWARE LIST
Pull Handle
3 pcs.
Machine Screw
for Pull Handle
6 pcs.
Wood Screw (short)
for base part
18 pcs.(+1 extra)
Wood Screw (long)
for side part
24 pcs.(+1 extra)
Insert the remaining (6) 1/2 screwsp
into the pre-drilled holes on Base Part
(U5), then tighten all screws.
(See the figure 3)
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.
U1.
Front Part
1 pc. for each
drawer.
Slide the Plywood Base Part (U5) into
the grooves on Side Parts (U3) and (U4).
Be sure to push the plywood all the way
forward so it meets the Front Part (U1).
(See the figure 2)
Unfinished Side
U2
U3
U4
U1
(Figure 1)
make sure roller
is on the back
UNIT PART LIST
Using a ,philips screwdriver
insert 1” screws into the pre-drilled
holes as shown, tighten half way.
(See the figure 1)
U1
(Figure 4)

V1
88 9100 002C
Drawer (V)
V3.
Side Part
1 pc. .
V5.
Base Part
1 pc.
V2.
Back Part
1 pc. .
V2
V2
V5
V5
V3
V4
V4
V4
V3
V3
V1
V1
V1
Assemble the Pull Handle
with Machine Screw on
the Front Part (V1).
(See the figure 4)
(Figure 1)
(Figure 2)
(Figure 3)
(Figure 4)
HARDWARE LIST
Pull Handle
1 pcs.
Machine Screw
for Pull Handle
2 pcs.
Wood Screw (short)
for base part
6 pcs.(+1 extra)
Wood Screw (long)
for side part
8 pcs.(+1 extra)
Insert the remaining (6) 1/2 screwsp
into the pre-drilled holes on Base Part
(V5), then tighten all screws
(See the figure 3)
make sure roller
is on the back
* If you are missing any of these parts,
please contact our DMI Customer
Service Department at 1-877-831-0319
or fax us at 1-800-755-2878.
V1.
Front Part
1 pc.
Slide the Plywood Base Part (V5) into
the grooves on Side Parts (V3) and (V4).
Be sure to push the plywood all the way
forward so it meets the Front Part (V1).
(See the figure 2)
Unfinished Side
V4.
Side Part
1 pc.
UNIT PART LIST
Using a ,philips screwdriver
insert 1” screws into the pre-drilled
holes as shown, tighten half way.
(See the figure 1)
Assembly Instructions