Home Styles 6652-53 User manual

Hardware List
Part List
6652-53
Swivel Chair
IMPORTANT
C.
Base
1 pc.
B.
Connector
1 pc.
F.
Side Frame
1 pc.
G.
Side Frame
1 pc.
Wrench
1 pc.
Flat Washer (long)
4 pcs. (+1 extra)
M8x35
Bolt
4 pcs. (+1 extra)
Spring Washer (large)
4 pcs. (+1 extra)
Spring Washer
8 pcs. (+1 extra)
Nut
4 pcs. (+1 extra)
Cap (large)
8 pcs. (+1 extra)
Cap
8 pcs. (+1 extra)
Carefully remove all the parts from the carton and place them
individually on a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
This product is made of aluminum. Do not use power tools
above 8 volts to assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
D.
Back
1 pc.
E.
Seat
1 pc.
M6x20
Head Cap Bolt
8 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
Hex Wrench
1 pc.

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Wrench as the bolts may need to be tightened in the future.
STEP 1
Place Side Frame (F) on a soft cloth.
Attach Back (D) and Seat (E) to
Side Frame (F) with Flat Washers,
Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
(See Figure 1)
STEP 2
Place Side Frame (G)
on a soft cloth.
Attach unit to Side Frame (G)
with Flat Washers, Spring Washers and
Head Cap Bolts, tightening bolts only halfway.
Tighten all Bolts used in Steps 1 and 2.
Cover all Head Cap Bolts with Caps.
Cap
Head Cap Bolt
Spring Washer
Flat Washer
Figure 1
Head Cap Bolt
Spring Washer
Flat Washer
D
E
F
G

Assembly Instructions /33
STEP 3
Attach unit to Connector (B) with Bolts,
Flat Washers (long), Spring Washers (large)
and Nuts, tightening bolts and nuts only halfway.
(See Figure 2)
Tighten all Bolts and Nuts.
Cover all Bolts and Nuts with Caps (large).
Figure 2
Cap (large)
Bolt
Flat Washer (long)
Seat (A)
Cap (large)
Connector (B)
Flat Washer (long)
Spring Washer (large)
Nut
B
STEP 4
Place unit onto Base (C).
C

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 2 years of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460