Home Styles The Aspen 88 5520 51 User manual

Part List
Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
A.
Top
1 pc.
B.
Top
1 pc.
Cam Lock
14 pcs.(+4 extra)
Cam Lock Screw
14 pcs.(+1 extra)
Machine Screw
16 pcs.(+1 extra)
D.
Side Panel
1 pc.
H.
Back Stretcher
1 pc.
I.
Back Panel
2 pcs.
K.
Drawer
1 pc.
L.
Drawer
1 pc.
M.
Drawer
1 pc.
E.
Base
1 pc.
F.
Front Rail
1 pc.
G.
Front Rail
2 pcs.
(Knock-Down Construction,
please refer to the last page
of these instructions for
drawer assembly steps)
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Wood Screw (short)
18 pcs.(+1 extra)
Wood Screw (long)
28 pcs.(+1 extra)
C.
Side Panel
.1 pc
J.
Metal Strip
2 pcs.
88 5520 51
The Aspen
Front Slide-out Desk
Pull Handle
8 pcs.
Wood Screw
for Back Panel
26 pcs.(+1 extra)
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Head Cap Bolt
8 pcs. (+1 extra)
Flat Washer
4 pcs. (+1 extra )
Spring Washer
4 pcs. (+1 extra )

STEP 1
STEP 2
Assembly Instructions 2/7
F
Cam Lock Screw
Insert Cam Lock Screws into
the pre-drilled holes of Top (A), (B),
Side Panel (C) and (D).
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to
tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly.
Use the included adjustable levelers to level. A
Attach Front Rails (F), (G) and Base (E)
to Side Panel (C) with Cam Locks (see Figure 1)
and Head Cap Bolts. (See Figure 2)
Attach Side Panel (D) to unit with Cam Locks
and Head Cap Bolts.
Figure 1
Figure 2
Cam Lock Screw
Cam Lock
Head Cap Bolt
E
B
C
D
C
G
G
F
D

Assembly Instructions 3/7
Flat Washer
Spring Washer
Head Cap Bolt
Insert Head Cap Bolts, Spring Washers and
Flat Washers into the-drilled holes of Base (E).
(See Figure 3)
Turn unit to its’ up-right position.
Pull out the front legs.
Attach Top (B) to unit with
Cam Locks.
Attach Top (A) to unit with
Cam Locks.
STEP 3
A
B
STEP 4
E
Figure 3
Flat Washer
Spring Washer
Head Cap Bolt

Assembly Instructions 4/7
Slide Drawers (K), (L) and (M)
into position.
STEP 7
Place Metal Strips (J) into position.
Adjust the Metal Strip for letter size or
legal size files as shown.
Legal Size
Letter Size
STEP 5 K
L
M
STEP 6
J
J
Note: Please make sure unit is level before tightening these screws.Figure 4
H
I
I
Wood Screw for Back Panel
Wood Screws.
To level the unit, adjust the adjustable levelers on the
bottom of unit. (See Figure 4)
Attach upper Back Panel (I)
to unit with
Attach lower Back Panel (I) and
Back Stretcher (H) to unit with
Wood Screws.

K5.
Base Part
1 pc.
K2.
Back Part
1 pc.
K3.
Side Part
1 pc.
K4.
Side Part
1 pc.
Assembly Instructions 5/7
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
K2
K2
K2
K3
K3
K3
K4
K4
K4
K5
K5
K1
K1
K1
Drawer (K)
Part List
Figure 3
Figure 4
Attach K1 to K3 and K4,
using a
and wood screws ,
tighten halfway.
Attach K2 to K3 and K4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screwdriver
(4X)
(4X)
long
long
Insert wood screws (6X)
into the pre-drilled holes in K5,
tighten screws. (see Figure 3)
short
Slide K5 into the grooves in K3
and K4. Be sure to push K5 all
the way forward so it meets K1.
(see Figure 2)
STEP 1
STEP 2
STEP 3 STEP 4
Tighten all screws used in drawer assembly.
Assemble Pull Handle with
machine screws. (see Figure 4)
K1.
Front Part
1 pc.

L5.
Base Part
1 pc.
L2.
Back Part
1 pc.
L3.
Side Part
1 pc.
L4.
Side Part
1 pc.
Assembly Instructions 6/7
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
L2
L2
L2
L3
L3
L3
L4
L4
L4
L5
L5
L1
L1
L1
Drawer (L)
Part List
Figure 3
Figure 4
Attach L1 to L3 and L4,
using a
and wood screws ,
tighten halfway.
Attach L2 to L3 and L4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screwdriver
(4X)
(4X)
long
long
Insert wood screws (6X)
into the pre-drilled holes in L5,
tighten screws. (see Figure 3)
short
Slide L5 into the grooves in L3
and L4. Be sure to push L5 all
the way forward so it meets L1.
(see Figure 2)
STEP 1
STEP 2
STEP 3 STEP 4
Tighten all screws used in drawer assembly.
Assemble Pull Handle with
machine screws. (see Figure 4)
L1.
Front Part
1 pc.

Assembly Instructions 7/7
Part List
M1.
Front Part
1 pc.
M5.
Base Part
1 pc.
M2.
Back Part
1 pc.
M3.
Side Part
1 pc.
M4.
Side Part
1 pc.
Figure 1
Figure 2
M2
M2
P2
M3
M4
M4
M5
M5
M1
M1
Drawer (M)
Figure 3
Attach M1 to M3 and M4
using a
and wood screws ,
tighten halfway.
Attach M2 to M3 and M4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screwdriver
(6X)
(6X)
long
long
Insert wood screws (6X)
into the pre-drilled holes in M5,
tighten screws. (see Figure 3)
short
Slide M5 into the grooves in M3
and M4. Be sure to push M5 all
the way forward so it meets M1.
(see Figure 2)
STEP 1
STEP 2
STEP 3 STEP 4
Tighten all screws used in drawer assembly.
Assemble Pull Handle with
machine screws. (see Figure 4)
Figure 4
M3