Home Styles 88 5008 941 User manual

Hardware List
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Hex Wrench
1 pc.
Cam Lock
8 pcs.(+1 extra)
Cam Lock Screw
8 pcs.(+1 extra)
Machine Screw
4 pcs.
Drawer
Pull Handle
4 pcs.
Small
Hex Wrench
1 pc.
Adjustable Pin
16 pcs. (+1 extra)
I.
Shelf
4 pcs.
Part List (in this carton)
O.
Drawer
2 pcs.
C.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
J.
Bottom
1 pc.
B.
Side Panel
1 pc.
G.
Back Rail
1 pc.
E.
Front Rail
1 pc.
F.
Front Rail
1 pc.
K.
Back Panel
2 pcs.
L.
Back Piece
1 pc.
M.
Door
1 pc.
(Knock-Down Construction, please refer
to the last page of these instructions for
drawer assembly steps)
N.
Door
1 pc.
Wood Screw (short)
for Back Rail
8 pcs. (+1 extra)
Wood Screw (short)
for Drawer Base Part
8 pcs. (+1 extra)
Wood Screw (long)
for Drawer Side Part
16 pcs. (+1 extra)
88 5008 941
Kitchen Island
(Black Finish)
Monarch
H.
Back Rail
1 pc.
Head Cap Bolt
(long)
6 pcs. (+1 extra)
Head Cap Bolt
12 pcs. (+1 extra)
Head Cap Bolt
(short)
4 pcs. (+1 extra)
Cross Dowel
6 pcs. (+1 extra)

C
Assembly Instructions 2/7
IMPORTANT
Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
B
STEP 1
Insert Cam Lock Screws into the pre-drilled holes of Side .
(see Figure 1)
Panels (B) and (C)
STEP 2
Attach Side Panel (B) to Base (J) with
Head Cap Bolts (long) and Cross Dowels.
Attach Back Rail (H) to Side Panel (B) using
Cam Lock.
Attach Back Piece (L) to Back Rail (H)
and slide Back Panels (K) into place.
Attach Back Rail (G) to the unit using
Cam Lock.
(see Figure 2)
(see Figure 3)
Cam Lock Screw
(Figure 1)
Cam Lock
Cross Dowel
Head Cap Bolt (long)
J
G
H
K
K
L
B
(Figure 3)
(Figure 2)

Assembly Instructions 3/7
STEP 4
C
E
F
D
Attach Side Panel (C) to unit
with Head Cap Bolts (long),
Cross Dowel and using
Cam Locks.
Insert 8x Wood Screws from
the back of unit, tighten up all
the Screws. (see Figure 4)
STEP 3
Attach Middle Panel (D) to unit with
Head Cap Bolts and Cross Dowels.
Attach Front Rail (E) and (F) to unit
using Cam Locks.
(Figure 4)
Wood Screw (short)
for Back Rail
Cam Lock
Cross Dowel
Head Cap Bolt (long)
Cam Lock
Head Cap Bolt (long)
Cross Dowel

Assembly Instructions 4/7
(Figure 5) (Figure 6)
STEP 5
Attach Frame Leg (P) and (Q)
to unit with Head Cap Bolts.
STEP 6
Slide Drawer (O) into place.
Insert Adjustable Pin into side panels
and middle panels at the
desired level.
Slide Shelf (I) into position.
Assemble Pull Handles to
Door (M) and (N) with Machine
Screws.(see Figure 6)
Attach Doors (M) and (N) to
the side panels, by sliding the
door lift hinges into the side
panel lift hinges.(see Figure 5)
N
I
I
O
M
O
Adjustable Pin
P
Q
Head Cap Bolt
II

N2
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
O2
O3
O4
O5
O5
O1
Figure 3
Figure 4
Insert wood screws (4X)
into the pre-drilled holes in N5
and tighten (see Figure 3)
short
Slide O5 into the grooves in O3
and O4. Be sure to push O5 all
the way forward so it meets O1.
(see Figure 2)
STEP 2
STEP 3
STEP 4
Tighten all screws used in drawer assembly.
Assemble Pull Handle with
machine screws. (see Figure 4)
Assembly Instructions 5/7
Part List
O1.
Front Part
2 pcs.
O5.
Base Part
2 pcs.
O2.
Back Part
2 pcs.
O3.
Side Part
2 pcs.
O4.
Side Part
2 pcs.
Drawer (O)
Attach O1 to O3 and O4, using
a and
wood screws ,
tighten halfway.
Attach O2 to O3 and O4 using
wood screws ,
tighten halfway. (see Figure 1)
Phillips screwdriver
(4X)
(4X)
long
long
O4
O3 O1
O2
Figure 1
STEP 1
N3
O4
O1
O2
O3

Assembly Instructions 6/7
STEP 7
Pull out the Drawers from unit.
Place Top (A) onto the unit, using
Head Cam Bolts (short). (see Figure 7)
Side Drawers into place.
A
Head Cap Bolt (short)
(Figure 7)

Assembly Instructions 7/7
Holding the Leaf Top up, pull
out a back leg from the unit;
then pull out the other
back leg.
Top Extension Instructions
STEP 2
Lift up the Leaf Top.
STEP 1