Home Styles 88 5538 952 User manual

or other damages occuring to the wood parts.
Tools Required For Assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
88 5538 952
PART LIST (in this carton)
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
HARDWARE LIST
Casual Attire For Today's Home
Large Kitchen Cart
(Oak Finish)
I.
Shelf
2 pcs.
A.
Top
1 pc.
O.
Back Piece
2 pcs.
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
F.
Middle Panel
1 pc.
G.
Divider
1 pc.
H.
Shelf
2 pcs.
B.
Base
1 pc.
J.
Front Rail
1 pc.
K.
Front Rail
1 pc.
L.
Door
1 pc.
M.
Door
1 pc.
V.
Drawer
2 pcs.
N.
Back Panel
2 pcs.P.
Back Panel
1 pc.
Q.
Back Rail
1 pc.
R.
Back Rail
1 pc.
S.
Arm
2 pcs.
T.
Arm
2 pcs.
U.
Towel Bar
2 pcs.
(Drawers require assembly.
Please refer to the last page
of these assembly instructions.)
Machine Screw
4 pcs.
Cam Lock Screw
20 pcs. (+1 extra) Cam Lock
20 pcs. (+1 extra)
Head Cap Bolt
8 pcs. (+1 extra)
Pull Handle
4 pcs.
Wood Screw
for Drawer (Long)
16 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Caster
two lock
two non-lock
4 pcs.
Wood Screw
for Caster
16 pcs. (+1 extra)
Wood Screw
for Drawer (Short)
12 pcs. (+1 extra)

Assembly Instructions 2/6
Attach four Caster underneath Base (B) with
Wood Screws for Caster. (see Figure 1)
(See ‘Arrow’ sticker indicating front side)
Insert Cam Lock Screws into the pre-drilled holes of
Base (B) then tighten.
STEP 2
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in a safe place as you may need to tighten the Head Cap Bolts in the future.
A
C
D
B
B
Insert Cam Lock Screws into the pre-drilled
holes of Side Panel (C),(D) and Top (A)
then tighten.
STEP 1
Cam Lock Screw
Cam Lock Screw
Locking Caster
(On Front)
Locking Caster
(On Front)
Cam Lock Screw
Figure 1

BC
Assembly Instructions 3/6
O
Q
DN
O
DP
DN
Attach Middle Panel (E) , (F)
to unit.
Attach Front Rail (K) to unit
with Cam Lock.
Attach Divider (G) to unit.
Attach Front Rail (J) to unit
with Cam Lock. (see Figure 2)
STEP 4
Cam Lock
DK
DJ
DG
DE DF
DR
Attach Back Rail (G) to Side Panel (C) with Cam Lock.
Attach Back Piece (O) to Back Rail (G) and slide Back Panel (N) , (P) into place.
Attach Back Rail (Q) to the unit with Cam Lock. (see Figure 2)
STEP 3
Cam Lock
Figure 2

Assembly Instructions 4/6
Attach Base (B) to unit with Cam Locks.
STEP 6
DB
DD
Attach Side Panel (D) to unit with Cam Locks.
STEP 5
Cam Lock
Cam Lock

Attach Door (L) , (M) to the
unit by sliding the door lift
hinges into side panel hinges.
(see Figure 4)
Assembly Instructions 5/6
Assemble Pull Handles to
Door (L) , (M) with Machine
Screws. (see Figure 5)
Insert Adjustable Pins into
side panels and middle
panels at the desired level.
Slide Shelf (H) , (I) into place.
Side the Drawer (V) into position.
STEP 8
DU
DA
DS
DT
DS
DU
DT
Adjustable Pin
Cam Lock
DM
DH
DI
DV DV
DIDI
DH
DL
Head Cap Bolt
Attach Arms (S) to unit with
Head Cap Bolts.
(see Figure 3)
Attach Towel Bars (U) to
pre-drilled hole of Arm (S).
Attach Arms (T) to unit with
Head Cap Bolts.
Attach Top (A) to unit with
Cam Locks.
STEP 7
Figure 5
Figure 3
Figure 4

Assembly Instructions 6/6
Figure 1
Figure 2
MAKE SURE ROLLER
IS ON THE BACK
V2
V2
V2
V3
V3
V3
V4
V4
V4
V5
V5
V1
V1
V1
Drawer (V)
Part List
V1.
Front Part
2 pcs.
V5.
Base Part
2 pcs.
V2.
Back Part
2 pcs.
V3.
Side Part
2 pcs.
V4.
Side Part
2 pcs.
Attach V1 to V3 and V4, using
a Phillips screwdriver and
long wood screws (4X),
tighten halfway.
Attach V2 to V3 and V4 using
long wood screws (4X),
tighten halfway. (see Figure 1)
Insert short wood screws (6X)
into the pre-drilled holes in V5,
tighten screws. (see Figure 3)
Slide V5 into the grooves in V3
and V4. Be sure to push V5 all
the way forward so it meets V1.
(see Figure 2)
STEP 1
STEP 2
STEP 3
Tighten all screws used in
drawer assembly.
Figure 4
Attach hardware pulls with
machine screws.
(see Figure 4)
STEP 4
Figure 3