Home Styles 6800-20 User manual

Hardware List
Part List
6800-20
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
End Table
D.
Base
1 pc.
A.
Top
1 pc.
E.
Foot
4 pcs.
Small
Hex Wrench
1 pc.
Spring Washer
20 pcs. (+1 extra)
M6x35
Head Cap Bolt
20 pcs. (+1 extra)
Hex Wrench
1 pc. (+1 extra)
Flat Washer
20 pcs. (+1 extra)
C.
Panel
2 pcs.
B.
Panel
2 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach (D) to Panel (B) with Head Cap Bolts,Base
Spring Washers and Flat Washers,
tightening bolts only halfway.
(See Figure 1)
STEP 2
Attach Panel (C) to unit with
Head Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Figure 1
B
C
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
D

Assembly Instructions /35
B
STEP 3
Attach Panel (B) to unit with Head Cap Bolts,
Spring Washers and Flat Washers, tightening bolts only halfway.
Head Cap Bolt
Spring Washer
Flat Washer
STEP 4
Insert Head Cap Bolts, Spring Washers
and Flat Washers into unit, tightening bolts only halfway.
Flat Washer
Spring Washer
Head Cap Bolt

Assembly Instructions /45
C
STEP 5
Attach Panel (C) to unit with
Head Cap Bolts, Spring Washers
and Flat Washers,
tightening bolts only halfway.
Tighten all bolts used in
Steps 1, 2, 3, 4 and 5.
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E
STEP 6
Attach Feet (E) to unit with Head Cap Bolts,
Spring Washers and Flat Washers.
(See Figure 2)
Figure 2

Assembly Instructions /55
STEP 7
Turn over unit to its upright position.
Place (A) into position.Top
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 3) Figure 3
A

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460