Home Styles Flexsteel 5525-69 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Carton 20 05525 0691 is also needed for assembly.
20 05525 0692
Pantry
G.
Top
1 pc.
I.
Shelf
4 pcs.
J.
Back Rail
4 pcs.
O.
Top
1 pc.
P.
Bottom
1 pc.
N.
Back Panel
2 pcs.
H.
Bottom
1 pc.
K.
Upright
1 pc.
L.
Back Panel
2 pcs.
M.
Upright
1 pc.
Cam Lock Screw
28 pcs. (+2 extra)
Cam Lock
28 pcs. (+6 extra)
M3x15
Wood Screw
28 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
Magnet
4 pcs.
Bracket
2 pcs.
M4x45
Machine Screw
4 pcs.
Knob
4 pcs.

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into pre-drilled holes
in Side Panels (C), (D), (E), (F) and Bottoms (H), (P),
then tighten. (See Figure 1)
Cam Lock Screw
Cam Lock Screw
Figure 1
Figure 2
C
D
E
F
H
P
Wood Screw
Magnet
Cam Lock Screw
STEP 2
Insert Cam Lock Screws into
pre-drilled holes in Tops (G)
and (O), then tighten.
Attach Magnets to Top (G)
and (O) with Wood Screws into
pre-drilled holes. (See Figure 2)
G
O

Assembly Instructions 3/6
Figure 3 Figure 4 Figure 5
STEP 3
Attach Upright (K) to Back Rail (J).
Slide Back Panels (L) into position.
Attach Back Rail (J) to unit.
Attach Side Panels (C) and (D)
to unit with Cam Locks.
(See Figure 3)
Attach Bottom (H) to unit
with Cam Locks.
Cam Lock
C
D
J
LL
K
J
H
STEP 4
Attach Doors (A) and (B) to unit by sliding
door hinges into side panel hinges.
(See Figure 4)
Attach Knobs to Doors (A) and (B)
with Machine Screws.
(See Figure 5)
Attach Top (G) to unit with Cam Locks.
Machine Screw
Knob
Cam Lock
A
B
G

Assembly Instructions 4/6
STEP 5
Attach Upright (M) to Back Rail (J).
Slide Back Panels (N) into position.
Attach Back Rail (J) to unit.
Attach Side Panels (E) and (F)
to unit with Cam Locks.
Attach Bottom (P) to unit with Cam Locks.
Cam Lock
E
F
J
J
N
N
M
P
STEP 6
Attach Doors (A) and (B) to unit by sliding
door hinges into side panel hinges.
Attach Knobs to Doors (A) and (B)
with Machine Screws.
Attach Top (O) to unit with Cam Locks.
Cam Lock
Machine Screw
Knob
A
B
O

Assembly Instructions 5/6
STEP 7
Place top unit onto base unit.
Insert Adjustable Pins into
side panels at desired level.
Place Shelves (I) into position.
Figure 6 Figure 7
Adjustable Pin
STEP 8
Attach Brackets to unit with Wood Screws.
(See Figure 6)
Level unit by adjusting the adjustable
levelers on bottom of unit.
(See Figure 7)
Note: Unit must be level to proceed.
Insert Wood Screws into pre-drilled holes
in unit, then tighten.
Note: Unit must be level before tightening these screws.
Wood Screw
Bracket

Assembly Instructions 6/6
Hardware List
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
STEP 9
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 8)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Figure 8
Wood Screw
Wall Screw Pre-drilled hole
at top of unit
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319